WAGO 761-210 Manuals

Manuals and User Guides for WAGO 761-210. We have 1 WAGO 761-210 manual available for free PDF download: Manual

WAGO 761-210 Manual (84 pages)

Telecontrol module for fault detection/indication, monitoring and remote control

Brand: WAGO | Category: Control Unit | Size: 2.42 MB

Table of Contents
3
Notes about this Documentation
6
Validity of this Documentation
6
Copyright
6
Symbols
7
Number Notation
9
Font Conventions
9
Table 1: Number Notation
9
Table 2: Font Conventions
9
Important Notes
10
Legal Bases
10
Subject to Changes
10
Personnel Qualification
10
Use of the TO-PASS Telecontrol Modules in Compliance with Underlying Provisions
10
Technical Condition of Specified Devices
10
Disclaimer
11
Firmware Licensing Terms
11
Firmware with Open Source GPL
11
Block Rounding for GPRS Connections
11
Safety Advice (Precautions)
12
Device Description
15
Scope of Delivery
15
Use
15
Table 3: Overview of Functions
16
View
17
Figure 1: Front View
17
Connectors
18
Antenna
18
Figure 2: Antenna Connection
18
Operating Voltage
19
Figure 3: Terminal Assignment for Operating Voltage
19
Table 4: Terminal Assignment for Operating Voltage
19
Grounding
20
Framework Assembly
20
Insulated Assembly
20
Grounding of the TO-PASS
20
Telecontrol Module
20
Table 5: WAGO Ground Wire Terminals
20
Shielding
21
General
21
Bus Lines
21
Signal Lines
21
WAGO Shield Connecting System
22
Figure 4: Example of the WAGO Shield Connecting System
22
Digital Inputs
23
Figure 5: Terminal Assignment for Digital Inputs
23
Table 6: Terminal Assignment for Digital Inputs
23
Counter Inputs
24
Figure 6: Counter Input Pin Assignments
24
Table 7: Counter Input Pin Assignments
24
Digital Outputs
25
Figure 7: Terminal Assignment for Digital Outputs
25
Table 8: Terminal Assignment for Digital Outputs
25
Serial Interface to PC
26
Figure 8: Serial Interface to the PC and MODBUS Interface
26
Table 9: Serial Interface to the PC
26
Table 10: PC Interface Cable Assignment
26
Display Elements
27
Figure 9: Display Elements
27
Table 11: Display Elements
27
Technical Data
28
Housing
28
Supply
28
GSM Antenna Connection
28
Table 12: Technical Data Housing
28
Table 13: Technical Data Supply
28
Table 14: Technical Data GSM Antenna Connection
28
GSM Communication
29
Digital Inputs
29
Counter Inputs
29
Digital Outputs
29
Table 15: Technical Data GSM Communication
29
Table 16: Technical Data Digital Inputs
29
Table 17: Technical Data Counter Inputs
29
Table 18: Technical Data Digital Outputs
29
Approvals
30
Standards and Guidelines
30
Mounting
31
Mounting the TO-PASS ® Telecontrol Module to the DIN Rail
31
Figure 10: Mounting the TO-PASS ® Telecontrol Module to the DIN Rail
31
Removing the TO-PASS ® Telecontrol Module from the DIN Rail
32
Figure 11: Removing the TO-PASS ® Telecontrol Module from the DIN Rail
32
Connect Devices
33
Connecting the Push-Wire Connections to the Conductor
33
Connection Examples
34
Digital Inputs
34
Figure 12: Connection Example for Switch at Input DI1
34
Counter Inputs
35
Figure 13: Connecting Example, Switching Contact at Counter Input DI1
35
Digital Outputs
36
Figure 14: Connection Example for a Relay at DO1 Output
36
Commissioning
37
Installing the Operating Software
37
Starting the TO-PASS Telecontrol Module
38
Parameterizing
40
General Settings
40
Figure 15: General Settings
40
Table 19: General Settings
40
Reading Parameters from the Module
42
Identity
43
Figure 16: Configuring the Identity
43
Table 20: Configuring the Identity
44
Addresses
45
Figure 17: Configuring the Addresses
45
Table 21: Configuring the Addresses
46
Configuring Inputs and Outputs
48
Digital Inputs
48
Figure 18: Configuring Digital Inputs 1
48
Figure 19: Configuring Digital Inputs 5
49
Table 22: Configuring of Digital Inputs
49
Multiplex Input
52
Multiplex Settings
53
Figure 20: Configuring Multiplex Operation Settings
53
Table 23: Configuring Multiplex Operation Settings
53
Multiplex Alarm Text
54
Figure 21: Configuring Multiplex Operation Alarm Texts
54
Table 24: Configuring Multiplex Operation Alarm Texts
54
Digital Outputs
55
Figure 22: Configuring the Digital Outputs
55
Table 25: Configuring the Digital Outputs
55
Configuring Error Detectors
56
Alarm Messages for Digital Inputs
56
Limit Messages for Counter Inputs
56
Acknowledgement
57
Figure 23: : Configuring the Acknowledgment Response
57
Table 26: Configuring the Acknowledgement Response
57
Transmission Repeat Times
58
Figure 24: Configuring the Transmission Repeat Times
58
Table 27: Configuring the Transmission Repeat Times
59
Time Adjustment
61
Figure 25: Setting the Time Adjustment
61
Table 28: Setting the Time Adjustment
61
Writing Parameters to the Module
62
Operation
63
Remote Query of Process Values
63
Remote Polling Via SMS
64
Table 29: SMS Format
64
Table 30: Items Added to SMS for Counter Inputs
64
Table 31: Counter Status
65
Remote Polling Using the TO-PASS Operating Program
66
Inputs/Outputs
67
Figure 26: Visualization of the Process Values
67
Counters
68
Figure 27: Counter Process Values
68
Telecontrol
69
Telecontrol Via SMS
70
Setting or Resetting a Digital Output
70
Table 32: Example of Parameters for Set DO
70
Changing the Counter Value or Status
71
Table 33: Control Commands for Counters
71
Telecontrol with the TO-PASS
72
Operator Program
72
Inputs/Outputs
73
Figure 28: Visualization of the Process Values
73
Counters
74
Figure 29: Counter Process Values
74
Acknowledging Error Messages
75
Switching to Standby
76
Diagnostics
77
Test Inputs and Outputs
77
Figure 30: Test Inputs and Outputs
77
Testing the Counter Inputs
78
Figure 31: Testing Counters
78
Testing the Connection
79
Figure 32: Testing the Connection
79
Testing the Modem
80
Figure 33: Testing the Modem
80
List of Figures
81
List of Tables
82

WAGO Categories

I/O Systems Control Unit

Power Supply

Switch Controller

More WAGO Manuals

WAGO 761-210 Manuals

WAGO 761-210 Manual (84 pages)

Table of Contents

Related Products

WAGO Categories