Sign In
Upload
Manuals
Brands
Fluke Calibration Manuals
Test Equipment
5730A
Fluke Calibration 5730A Manuals
Manuals and User Guides for Fluke Calibration 5730A. We have
2
Fluke Calibration 5730A manuals available for free PDF download: Operator's Manual, Service Manual
Fluke Calibration 5730A Operator's Manual (260 pages)
Multifunction Calibrator
Brand:
Fluke Calibration
| Category:
Test Equipment
| Size: 6.27 MB
Table of Contents
Table of Contents
5
Introduction and Specifications
15
Chapter 1
19
Introduction
19
Safety Information
21
Symbols
22
How to Contact Fluke Calibration
23
Instruction Manuals
23
Wideband AC Voltage Module (Option 5700A-03)
24
Auxiliary Amplifiers
24
5725A Amplifier
25
52120A Amplifier
25
Support Equipment and Services
25
732B Direct Voltage Reference Standard
26
200 Direct Volt Maintenance Program (USA Only)
26
742A Series Resistance Standards
26
Wideband AC Module (Option 5700A-03) Calibration Support
26
The Components of the Calibrator
27
Specifications
27
Specification Confidence Levels
27
Use of Absolute and Relative Accuracy Specifications
28
Use of Secondary Performance Specifications
28
General Specifications
29
Electrical Specifications
31
DC Voltage Specifications
31
AC Voltage Specifications
32
Resistance Specifications
38
DC Current Specifications
41
AC Current Specifications
43
Wideband AC Voltage (Option 5700-03) Specifications
46
52120A Specifications When Operated with the 5730A
47
52120A Electrical Performance Limits
47
Operated Within 5730A Control Loop (All Current Ranges)
48
Coverage Factor K=2.58 (99 % Confidence Level)
48
Coverage Factor K=2.00 (95 % Confidence Level)
48
52120A/COIL 3 KA 25-Turn Coil
49
52120A/COIL 6 KA 50-Turn Coil
49
Installation
51
Chapter 2
53
Introduction
53
Unpack and Inspect the Calibrator
53
Placement and Rack Mounting
54
Cooling Considerations
54
Mains Voltage Selection
54
Connect to Mains Power
56
Connect a 5725A Amplifier
56
Connect a 52120A Amplifier
56
Features
57
Introduction
59
Front-Panel Features
59
Rear-Panel Features
63
Front-Panel Operation
65
Chapter 4
67
Introduction
67
Turn on the Calibrator
67
Warmup
68
Product Use
68
Reset the Calibrator
68
Operate and Standby Modes
68
Connect the Calibrator to a UUT
69
Recommended Cable and Connector Types
69
When to Use External Sensing
71
When to Use the External Voltage Guard
71
Four-Wire Vs. Two-Wire Resistance Connections
71
Cable Connection Instructions
72
Set the Output
79
DC Voltage Output
81
AC Voltage Output
82
DC Current Output
84
AC Current Output
86
Resistance Output
88
Wideband AC Voltage Output (Option 5700A-03)
91
Variable Phase Output
93
Phase Locking to an External Signal
94
Auxiliary Amplifier Use
95
5725A Amplifier Output
96
52120A Transconductance Amplifier Output
97
Error Mode Operation
97
Error Mode Overview
98
Enter Error Mode
98
Exit Error Mode
98
Use Error Mode
99
Read the UUT Error: AC and DC Voltage and Current Output
99
Read the UUT Error: Resistance Output
100
Introduction to Offset, Scale, and Linearity Errors
100
Offset Error
101
Scale Error
101
Linearity Error
102
Combine the Error Types
103
Program an Offset
104
Program a Scale Factor
105
Linearity Check with Offset and Scale
106
Set up the Calibrator
110
Setup Menu
110
Setup Menu Rules
111
Menu Description
112
Touchscreen Selections
112
Instrument Setup
116
Uncertainty Information Menu
117
Set Output Limits
118
Select Boost Amplifiers
119
Error Reference
119
Instrument Settings
121
Set the Internal Clock/Calendar
121
Language
122
Display Brightness
122
About this Instrument
122
Remote Interface Setup
123
Chapter 5
125
Introduction
125
GPIB (IEEE-488) Interface
125
Use the IEEE-488 Port for Remote Control
125
IEEE-488 Bus Restrictions
125
Bus Setup Procedure
126
IEEE-488 Interface Configuration
126
Bus Communication Overview
127
RS-232 Serial Interface
127
Use the RS-232 Port for Remote Control
127
RS-232 Interface Specifications
128
Set up and Connect the Serial Interface
128
Serial Remote Control Setup Procedure
129
Exceptions for Serial Remote Control
129
Ethernet Interface
130
Set up and Connect the Ethernet Interface
130
Set the IP Address
130
Select the Dynamic Host Configuration Protocol (DHCP)
130
Set a Static Internet Address
131
Configure the General Network Socket Port
131
Configure the LAN Default Gateway
132
Set the LAN Subnet Mask
132
Read the MAC Address
132
Establish an Ethernet Connection
133
Terminate an Ethernet Connection
133
Use of Ethernet Remote Control
133
Use of USB 2.0 Remote Control
134
Remote Commands and Syntax
135
Introduction
137
Chapter 6
137
Parameter Syntax Rules
137
Extra Space Characters
138
Terminators
138
Incoming Character Processing
138
Response Message Syntax
139
Input Buffer Operation
139
Commands
140
Multiple Commands
140
Coupled Commands
140
Sequential and Overlapped Commands
141
Commands Ignored When Not in Remote
141
Commands that Require the Calibration Security Passcode
141
Long Term Commands
141
Definition: Queries and Commands
142
Functional Elements of Commands
142
Interface Messages (IEEE-488 Only)
144
Use of *OPC?, *OPC, and *WAI
146
Fault Queue
151
Local-To-Remote State Transitions
184
Check the Calibrator Status
186
Serial Poll Status Byte
188
Service Request Line (SRQ)
188
Service Request Enable Register
188
Load the SRE
188
Event Status Register
189
Bit Assignments for the ESR and ESE
189
Read the ESR and ESE
190
Load the ESE
190
Instrument Status Register
190
Instrument Status Change Register
190
Instrument Status Change Enable Register
190
Bit Assignments for the ISR, ISCR, and ISCE
190
Read the ISR, ISCR, or ISCE
191
Load the ISCE
191
Fault Queue
191
Operator Maintenance and Calibration
193
Chapter 7
194
Introduction
194
Fuse Replacement
194
Clean the Air Filter
196
Clean the Exterior
197
User-Replaceable Parts
197
5730A Calibration
199
The Artifact Calibration Process
199
Establish Traceability
200
Calibration Reports
200
Range Adjustment
200
DC Zeros
200
Run DC Zeros
200
DC Zeros Reminder
201
Calibration
201
Calibration Security Passcode
202
Artifact Calibration
202
When to Adjust Calibrator Accuracy
203
Calibration Procedure
203
Range Adjustment
206
Range Adjustment
207
Calibrate the Wideband AC Module (Option 5700A-03)
210
Wideband Flatness Calibration Procedure
211
Calibration Check
213
Develop a Performance History
213
Save Calibration Reports
214
Calibration Shift Results
214
Calibration Check Shift Results
215
Raw Data Results
215
Options and Accessories
217
Chapter 8
219
Introduction
219
Wideband AC Voltage Module (Option 5700A-03)
219
Accessories
219
Low Thermal EMF Test Leads
220
Rack Mount Kits
220
Shielded IEEE-488 Interface Cables (Y8021 and Y8022)
220
DC Voltage Reference Standard (732B)
220
Ω and 10 Kω Resistance Standards (742A-1 and 742A-10K)
221
5725A Amplifier
221
52120A Amplifier
221
A Fault Codes
223
B ASCII and IEEE-488 Bus Codes
249
C Glossary
251
Advertisement
Fluke Calibration 5730A Service Manual (104 pages)
Multifunction Calibrator
Brand:
Fluke Calibration
| Category:
Test Equipment
| Size: 2.2 MB
Table of Contents
Table of Contents
5
Introduction
7
How to Contact Fluke Calibration
9
Safety Information
9
Specifications
9
Specification Confidence Levels
9
Use of Absolute and Relative Specifications
9
Use of Secondary Performance Specifications
10
Theory of Operation
10
Calibrator Overview
10
Digital Section Overview
10
Analog Section Overview
11
Functional Description Presented by Output Function
12
DC Voltage Functional Description
12
AC Voltage Functional Description
15
30 Mhz Wideband AC-V Functional Description (Option 5730A/03 Shipped before October 2015)
16
30/50 Mhz Wideband ACV Functional Description (Option 5730A/03 Shipped after October 2015 and Option 5730A/05)
16
DC Current Functional Description
16
AC Current Functional Description
17
Ohms Functional Description
17
Product Calibration
18
The Artifact Calibration Process
18
Establish Traceability
18
Calibration Reports
19
Range Adjustment
19
DC Zeros
19
Calibration Procedures
20
Calibration Security Passcode
22
Artifact Calibration
22
When to Adjust Product Specifications
23
Main Output Calibration Procedure
23
Range Adjustment
26
Calibrate the Wideband AC Module Options 5730A/03 and 5730A/05
29
Wideband Flatness Calibration Adjustment Procedure
31
Calibration Check
32
Develop a Performance History
32
Save Calibration Reports
33
Calibration Shift Results
33
Calibration Check Shift Results
34
Raw Data Results
34
Full Verification
35
Required Equipment for All Tests
35
Warmup Procedure for All Verification Tests
35
Determine Specification Limits for Other Calibration Intervals
36
Applying Guardbands to Specification Limits
37
Resistance Verification Test
40
Verify 0 Ω, 1 Ω, and 1.9 Ω
40
Verify 10 Ω through 19 MΩ
41
Verify 100 MΩ
44
DC Voltage Verification Test
44
DC Zero Test
45
Self-Calibrate a Fluke 752A Divider with a Fluke 8508A as the Null Detector
46
DC Voltage Test at Decade Values
50
DC Voltage Test at 19 Volts
54
Direct Current Verification Test
56
AC Voltage Frequency Accuracy Test
59
AC Voltage Verification Test
60
Alternating Current Verification Test
64
Ma to 2 a Ranges
65
Μa Range
66
Wideband Frequency Accuracy Test
70
Wideband AC Voltage Module Output Verification
70
Wideband Output Accuracy at 1 Khz Test
71
Wideband Output Flatness Test
72
Maintenance
84
Clean the Exterior
84
Fuse Replacement
84
Clean the Air Filter
86
Access Procedures
87
Top and Bottom Covers
87
Digital Section Cover
87
Analog Section Covers
87
Rear Panel Removal and Installation
87
Rear Panel Assembly Access
88
Front Panel Removal and Installation
88
Display Assembly Removal and Installation
89
Keyboard Assembly Removal and Installation
89
Analog Assembly Removal and Installation
90
Digital Assembly Removal and Installation
92
Power Transformer Removal and Installation
92
Replacement Parts
93
Advertisement
Related Products
Fluke Calibration 5322A
Fluke Calibration 55 Series
Fluke Calibration 5520A-PQ
Fluke Calibration 5520A-PQ/3
Fluke Calibration 5522A/6
Fluke Calibration 5522A-PQ
Fluke Calibration 5080A
Fluke Calibration 5560A
Fluke Calibration 525B
Fluke Calibration 5522A
Fluke Calibration Categories
Test Equipment
Measuring Instruments
Water Pump
Monitor
Power Supply
More Fluke Calibration Manuals
Login
Sign In
OR
Sign in with Facebook
Sign in with Google
Upload manual
Upload from disk
Upload from URL