Table of Contents
Advertisement
Lighting Burners (ESIRS)
Surface Burners- Electronic Safety
Ignition/Re-ignition System (ESIRS)
To light the knob surface burners, turn the
appropriate control knob counter-clockwise
to any position. This control is both a gas
valve and an electric switch. When you turn
the control knob to any on position, you will
hear a clicking sound. This is the sound of
the electronic safety re-ignition system
(ESIRS) that will ignite the corresponding
burner with a 3 seconds safety delay. Once
ignited, the clicking sound will stop. If the
flame goes out for any reason, the burner
will automatically attempt to re-ignite one
time. If it fails to re-ignite, the ESIRS will
automatically shut down the gas feed to the
burner. Five seconds later, the ESIRS will
automatically attempt to re-ignite the burner
one time by re-opening the gas feed. You
will hear a clicking sound again. If the burner
fails to re-ignite once more, the above cycle
will be repeated.
After 5 attempts to re-ignite the burner, the
ESIRS will automatically shut down the gas
feed to the burner completely. To restart the
ignition process you must turn the knob to
the off position and to any on position
again. After a 2 seconds safety delay the
ignition process will begin again. When the
burner lights, you can turn the burner
control to any position to adjust the flame
size. Setting the proper height for the
desired cooking process and selected utensil
will result in superior cooking performance,
while also saving time and energy. Within a
few moments, enough gas will have traveled
to the burner to light. When the burner
lights, turn the burner control to any position
to adjust the flame size. Setting the proper
flame height for the desired cooking process
and selecting the correct cooking vessel will
result in superior cooking performance, while
also saving time and energy.
14
General Information
Electrical Requirement
CAUTION
Check your national and local codes
regarding this unit. This cooktop requires
BURN HAZARD
The use of cabinets for storage above the
220-240V, 50/60 Hz; 122 cm, 3-wire cord
appliance may result in a potential burn
with grounded 3-prong plug attached to
hazard. Combustible items may ignite,
unit. See "Electrical Connection" section for
metallic items may become hot and
grounding instructions. Must be fused
cause burns. If a cabinet storage is to be
separately from any other circuit.M
provided the risk can be reduced by
installing a range hood that projects
Air Supply and Ventilation
horizontally a minimum of 12.7 cm
Means must be provided for any heavy-duty
beyond the bottom of the cabinets.
cooking appliance to exhaust combustion
waste product to the outside of the building.
It is recommended that the cooktop be set
under a powered, vented exhaust hood, or
WARNING
non-vented recirculating hood. Nothing
This appliance shall not be used for
should obstruct the flow of combustion and
space heating. This information is based
ventilation air.
on safety considerations.
• All openings in the wall behind the
appliance and in the floor under the
appliance shall be sealed.
• Keep appliance area clear and free from
combustible materials, gasoline, and other
flammable vapors.
• DO NOT obstruct the flow of combustion
IMPORTANT:
and ventilation air.
must replaced by a Viking qualified
technician or a Viking Range Corporation
• Disconnect the electrical supply to the
appliance before servicing.
representative in order to avoid a hazard.
When removing cooktop for cleaning and/or
service:
• Shut off gas at main supply
• Disconnect AC power supply
• Disconnect gas line to the inlet pipe.
• Lift appliance out of cabinet cutout.
15
WARNING
Electrical shock hazard.
To avoid the risk of electrical
shock, personal injury or death;
verify electrical power is turned
off at the breaker box and gas supply is
turned off until the oven is installed and
ready to operate, installation by an
authorized installer only.
If power cord is damaged, it
Advertisement
Table of Contents
