1. Manuals
  2. Brands
  3. MaxTech Manuals
  4. Monitor
  5. XT-5871
  6. User manual

MaxTech XT-5871 User Manual

15-inch high resolution color monitor
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
XT-5871
USER'S MANUAL
Features
• 0.28 mm Dot Pitch
• 1280 x 1024, Non-Interlaced
• 120 Hz Refresh Rate
• Power Saving Operation (VESA DPMS)
• Anti-Glare Screen
• Full Screen Display
• Digital Controls
• Low Radiation
• Plug and Play
• Three-Year Warranty
Part #MAN119 Rev. 1.0
CX1566

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the XT-5871 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for MaxTech XT-5871

Summary of Contents for MaxTech XT-5871

  • Page 1 XT-5871 USER'S MANUAL Features • 0.28 mm Dot Pitch • 1280 x 1024, Non-Interlaced • 120 Hz Refresh Rate • Power Saving Operation (VESA DPMS) • Anti-Glare Screen • Full Screen Display • Digital Controls • Low Radiation • Plug and Play •...

  • Page 2: Table Of Contents

    Table of Contents Section 1 General Information ... 2 Section 2 Installation ... 3 Section 3 Monitor Controls and LEDs ... 4 Section 4 Troubleshooting ... 5 Appendix A Specifications ... 6 Appendix B Video Cable Pinout ... 7 Appendix C Power Saving Modes (DPMS) ... 7 Appendix D Three Year Warranty ...

  • Page 3: Section 1 - General Information

    Section 1 - General Information Congratulations on purchasing a MaxTech 15-inch high resolution color monitor. The monitor uses one of the finest CRTs available in the industry. The 0.28 mm dot pitch non-glare tube provides a crisp and vivid color display for all popular applications.
  • Page 4 Figure 2-1 Connecting the Base 2.2 Connecting the Cable • Plug the 15-pin male connector on the video cable into the output connector on the rear of your computer system. The video output connector on your computer may be either in a location similar to Figure 2-2 or on an expansion board.

  • Page 5: Section 3 - Monitor Controls And Leds

    Section 3 - Monitor Controls and LEDs Figure 3-1 Controls and LEDs...

  • Page 6: Section 4 - Troubleshooting

    Master Power (On rear): Push to provide power to the monitor. This switch should be left ON for daily operation. Use the front panel On/Off control (5) to turn the monitor display on and off. Adjust: Press plus (+) to increase the setting for the selected control (9 through 14).

  • Page 7: Appendix A - Specifications

    Image is not centered • Adjust Vertical Position and Horizontal Position controls. Appendix A - Specifications Picture Tube Size Dot pitch Horizontal Freq 30-66KHz Vertical Freq. 50-120 Hz Resolution (Max.) 1280 x 1024 Video Dot Rate 100 MHz Data Area 10.2 in.

  • Page 8: Appendix B - Video Cable Pinout

    Horizontal and Vertical Synchronization signals. This mode reduces the monitor’s power consumption to 1W. When the synchronization signals are re-enabled the monitor returns to normal operation. Appendix D - Three Year Warranty MAXTECH warrants to the original buyer of this product against defects in SIGNAL Green Blue...
  • Page 9 Except as specified below, this warranty covers all defects in material or workmanship in this product. The following are not covered by the warranty: 1. Any product which is not distributed in North America by MAXTECH or which is not purchased in North America from an authorized MAXTECH Dealer.

  • Page 10: Appendix E - Notices

    EXCLUSION OF DAMAGES MAXTECH'S liability for any defective product is limited to the repair or replace- ment of the product, at our option. MAXTECH shall not be liable for: 1.
  • Page 11 All registered trademarks are the property of their respective owners. Copyright © 1997 MAXTECH. All rights reserved. No reproduction of this document in any form is allowed without written permission from MAXTECH. First Edition...

Table of Contents