Download Print this page
Olsberg 14/691-3 Instruction Manual

Olsberg 14/691-3 Instruction Manual

Static storage heater

Advertisement

Quick Links

OLSBERG
Instruction Manual
Static Storage Heater manual 14/69_-3 and automatic 14/69_-4
Static Storage Heater intelligent 14/70_-3

Advertisement

loading
Need help?

Need help?

Do you have a question about the 14/691-3 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Olsberg 14/691-3

  • Page 1 OLSBERG • Instruction Manual Static Storage Heater manual 14/69_-3 and automatic 14/69_-4 Static Storage Heater intelligent 14/70_-3...
  • Page 2 This instruction leaflet must be: • handed to the heater user after installation. The user is also to be instructed on the way this electric storage heater works. • read carefully, retained for further use, and handed over to a new owner/user. •...
  • Page 3: Installation Instructions

    (with built-in heating elements) and the bricks (SP36, SP38) are packaged separately. The packaging has be limited to the minimum nec- essary for safe transport and is made entirely of recyclable materials. 14/692-3 14/693-3 14/694-3 14/691-3 14/695-3 14/692-4 14/696-4 14/693-4 14/694-4 14/702-3 14/703-3...
  • Page 4: Installation

    Nominal Storage Dimensions Heating Weight Core brick Model charge capacity Voltage Width x Depth x Height elements ca. kg packs manual 14/691-3 0,85 345x170x700 1x0,85kW 2x SP36 14/695-3 10,4 455x170x700 1x1,3kW 2x SP38 14/692-3 13,6 565x170x700 1x1,7kW 4x SP36 1x0,85kW...
  • Page 5 Pull the front panel at the bottom 10cm outwards • Remove the heater from the packaging using the from the heater and push upwards to remove. feet and lay it onto a soft surface (the Styrofoam Take out the Styrofoam strip between the inside sheet can be used if necessary).
  • Page 6 Skirting boards of more than 120mm height must be cut out in the area around the heater. The heater is then fixed using the clearance spacer as shown (fig.14, Detail B). 14/692-3 14/693-3 14/694-3 14/691-3 14/695-3 14/692-4 14/696-4 14/693-4 14/694-4 14/702-3...
  • Page 7 Lean the heater against the wall so that it cannot • Static Storage Heater intelligent 14/70_-3 tilt forward. On Peak Supply (A1/Z1 und A2/Z2): The final fixing is made when the core bricks have Feed the electrical cable 3x1,5mm² through the left been installed and the heater has ‘settled’...
  • Page 8 • • Remove the Styrofoam strip between the heating Build up the complete rear brick columns. elements and the top insulation. Reinstall the heater elements (fig.20). Make sure that the element connection tabs are not damaged and also, that they fit neatly into the openings in the lower insulation.
  • Page 9 • Push the inside front panel firmly against the heater core and fix to the inner housing using the screws above and on the side. fig.22 • Now fix the heater to the wall using the screws through the heater rear panel left and right. fig.24 fig.23 •...
  • Page 10 • As the surfaces of the heater cabinet get hot in use, flammable or other objects presenting a dan- ger of fire must not be placed on, or near the heater. Do not, therefore, place any wooden objects, clothes or washing, newspapers, blankets or the like on or over the heater and do not put any pieces of furniture made of inflammable materials, nor spray tubes or similar objects closer than 25cm...
  • Page 11: Operation

    Operation - Cabinet stove-enamelled steel plate. • General - Feet We thank you for purchasing one of our heaters. It pressed steel plate, powder coated or painted. was manufactured in a modern production facility. An elegant form, simple operation, excellent heat- ing performance and reliability are the main fea- tures of this appliance.
  • Page 12 - Charging of automatic heaters, Model 14/69_-4 The adjustment of the charge takes place using the operating knobs on the top right of the heater (e, fig.29). The automatic Model 14/69_-4 appliances are fit- ted with a thermo-mechanical regulator, which monitors the heater charge up to 90% in relation to the room temperature.
  • Page 13 - Static Storage Heater intelligent, - Automatic Discharge Model 14/70_-3 With the control element ’f’ at setting “max.“ (see The charge control registers the outside tempera- fig.29), the air flap opens according to the resid- ture and converts this value into a control current. ual heat left in the storage core.
  • Page 14 Removing the control unit for servicing • The control unit can be easily removed in one piece for servicing work. This is done as follows: Remove front panel of heater. Remove right side panel if necessary. Open the plastic adjustment element cover (fig.30).
  • Page 15: Circuit Diagram

    Circuit diagram • manual: 14/691-3, 14/692-3, 14/693-3, 14/694-3, 14/695-3 2) 78/4514.4923...
  • Page 16 • automatic: 14/692-4, 14/693-4, 14/694-4, 14/696-4 2) 78/4514.4924...
  • Page 17 • intelligent: 14/702-3, 14/703-3, 14/704-3 1) 78/4514.7023...
  • Page 18 Olsberg GmbH Hüttenstraße 38 59939 Olsberg T +49 2962 805-0 F +49 2962 805-180 info@olsberg.com olsberg.com...