Configuring ISDN ..........13 Connectivity Options ..............4 Configuring Basic Rate ISDN ........... 13 What can the AR720 Do For You? ..........4 Configuring Primary Rate ISDN ..........14 The AR720 Feature Set ..............5 Configuring ISDN Dial on Demand ........16 About this Guide ................
ISDN channels just a few minutes. If you have any questions about the AR720 when extra capacity is required, and closes them when traffic router, contact your local distributor or reseller.
AT-VPNet ABOUT THIS GUIDE uses a separate daughter card that fits inside the AR720 to offload the processor-intensive task of data encryption, so Before you use your AR720 router in a live network, please routing performance is not affected.
This section describes how to connect the AR720 router to different physical devices and networks. Before you start, you should be aware that the AR720 router refers to its physical interfaces as ports and these are numbered, starting at 0. Ports on the base unit are numbered first, followed by ports on PICs (Port Interface Cards) in Bay 0 and Bay 1.
Page 7
Double-click the Hypertrm.exe icon. 2 In the Connection Description dialog box, enter a name for the connection (e.g. AR720) and select an icon from the scrolling list. Click “OK”. 3 In the Phone Number dialog box, from the “Connect using:”...
PORTS 100 COL LNK RX Connect the LAN to the Ethernet port on the rear panel of the AR720 using the supplied CAT 5 cable. 7 Select “Save” from the File menu to save the current session. This creates a connection icon with the name you Connect the LAN to the TP port on the rear panel of the AT-AR022 Ethernet PIC assigned in the HyperTerminal group.
National ISDN-1, 5ESS or DMS-100 formats, all of which Configuring an IP Network and Configuring a Novell IPX Network are supported by the AR720 router. If National ISDN-1 is later in this guide for more information about configuring ISDN available, you can select from a list of “Capability Packages”,...
CONNECTING TO A PRIMARY RATE ISDN SERVICE Configuring a Novell IPX Network later in this guide for more To connect an AR720 router with an AT-AR020 PRI E1/T1 PIC information about configuring ISDN calls and routing protocols. installed to a Primary Rate ISDN service, follow these steps:...
Page 11
2 Check that the terminal or modem’s communication settings match the settings of the asynchronous port. By default, asynchronous ports on the AR720 router are set to 9600 baud, 8 data bits, 1 stop bit, no parity and hardware flow control.
A R 7 2 0 R O U T E R Q U I C K S T A R T G U I D E Documentation and Tools CD-ROM The AR Series Router Documentation and Tools CD-ROM is For more information about using the Adobe Acrobat Reader, bundled with every AR router and includes: select “Acrobat Reader Help”...
A R 7 2 0 R O U T E R Q U I C K S T A R T G U I D E Configuring ISDN This section describes how to configure ISDN on the AR720 3 In countries other than the USA, the router’s ISDN router using the command line interface.
On the Remote Office router, create a call to the Head these steps: Office router: 1 The AR720 can operate in either TE or NT mode, using 75Ω ADD ISDN CALL=ROHO OUTSUB=LOCAL or 120Ω termination. The router is shipped with jumpers set to SEARCHSUB=LOCAL NUMBER=9876543 TE mode, 75Ω...
Page 15
A R 7 2 0 R O U T E R Q U I C K S T A R T G U I D E 2 Select the country in which the router is being operated, Each call has the same name (ROHO), and this name is passed using the command: via the called subaddress IE to provide identification to the remote end of the link.
A R 7 2 0 R O U T E R Q U I C K S T A R T G U I D E CONFIGURING ISDN DIAL ON DEMAND CONFIGURING ISDN BANDWIDTH ON DEMAND A PPP interface that uses an ISDN call as its physical interface A PPP interface can be configured to use up to two B channels can be configured for dial on demand operation.
World-Wide Web. BEFORE YOU START The AR720 router routes TCP/IP across the wide area network 1 Ensure that the routers to be configured are connected to using services like ISDN, Frame Relay and leased lines, enabling...
A R 7 2 0 R O U T E R Q U I C K S T A R T G U I D E and use a terminal emulation program like Windows™ on a dial-on-demand ISDN connection this may result in Terminal.
A R 7 2 0 R O U T E R Q U I C K S T A R T G U I D E Example output from the SHOW IP IP Routes ROUTE command for a basic TCP/IP ------------------------------------------------------------------------------- network.
This example illustrates the steps required to configure a pair 2 Connect a terminal to the console port (port 0) on each ® of AR720 routers to create a Novell IPX internetwork, using router, as described in the AR700 Series Router Quick Install the router’s command line interface.
A R 7 2 0 R O U T E R Q U I C K S T A R T G U I D E • Each network in a Novell internet, including all LANs and PPP interface is configured for dial on demand operation (see WAN links, must be assigned a network number.
A R 7 2 0 R O U T E R Q U I C K S T A R T G U I D E Save the Configuration Check that there are two circuits, and for each circuit check that the circuit is enabled, uses the correct interface and Save the new dynamic configuration as a script, by entering encapsulation (for Ethernet interfaces), the network number is...
A R 7 2 0 R O U T E R Q U I C K S T A R T G U I D E 3 Does the file server appear in the IPX service table of the 3 Repeat this procedure on the Remote Office router, Remote Office router? If the server does not appear in the defining one IPX circuit for the Ethernet interface and one for table, its presence can not be advertised to the local LAN.