Allied Telesis AR700 SERIES Quick Install Manual
Ar700 series router
Hide thumbs
Also See for AR700 SERIES:
- Hardware reference manual (62 pages) ,
- Release note (232 pages) ,
- How to configure (110 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Allied Telesis AR700 SERIES
Summary of Contents for Allied Telesis AR700 SERIES
- Page 1 AR700 SERIES ROUTER QUICK INSTALL GUIDE...
- Page 2 AR700 Series Router Quick Install Guide Document Number C613-04027-01 REV E. Copyright © 1999-2003 Allied Telesyn International, Corp. 19800 North Creek Parkway, Suite 200, Bothell, WA 98011, USA. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn.
-
Page 3: Documentation Roadmap
■ AR745 Quick Install Guide updates can be found at www.alliedtelesyn.co.nz/documentation/documentation.html. Package Contents The following items are included with each AR700 Series router. Contact your sales representative if any items are damaged or missing. ■ One AR700 Series router. ■... -
Page 4: Selecting A Site
AR700 Series Router Selecting a Site The router can be installed in a standard 19-inch rack or on a level surface such as a desktop or bench. When installing the router, choose a site that: ■ Allows adequate airflow around the router and its vents. - Page 5 AC versions of AR700 Series routers are fitted with a universal power supply that will function over the range 100-240 VAC and 50–60Hz. DC versions of AR700 Series routers require a supply voltage in the range 38-59V DC. The specific power supply requirements for a particular model are clearly displayed on the rear or underside of the router.
-
Page 6: Circuit Protection
AR700 Series Router Apply DC power to the router (for DC models) Before connecting the DC supply: Read the Safety and Statutory Information booklet. A copy of this booklet is included with each router. It is also included on the Documentation and Tools CD-ROM or can be downloaded from www.alliedtelesyn.co.nz/documentation/documentation.html. -
Page 7: Parity: None
Quick Install Guide Figure 2: DC Power inlet terminals on an AR740. DC Power FOR CENTRALIZED DC POWER CONNECTION, INSTALL ONLY IN A RESTRICTED AREA 38-75VDC , 2A Power inlet The System LED should flash for approximately 10 seconds as the router runs internal tests. - Page 8 This section describes how to establish a connection to the router through the GUI, so you can configure the router before installing it in your LAN. For more information about the GUI, see the AR700 Series User Guide. router Select a PC to browse to the...
- Page 9 100 COL PW RUN SY BAY 1 BAY 0 POWE ETH port AR700 Series Router router Access the ’s command line interface Access the CLI from the PC, as described in the previous “Using the CLI to configure a router” section.
- Page 10 Lit when there is an error in data transmission to or from a MAC or PAC. A full description of all AR700 Series router LEDs can be found in the AR Router Hardware Reference. Descriptions of NSM and PIC LEDs can be found in their respective Hardware References.
-
Page 11: Troubleshooting Installation
Quick Install Guide Troubleshooting Installation If you have problems installing the router, try one or more of the following: No LEDs Light The most likely reason is that the router is not receiving power. Check the following: Check the supply outlet’s switch is in the ON position. Test the main power outlet to verify it is working. -
Page 12: Documentation And Tools Cd-Rom
This AR700 Series Router Quick Install Guide, which outlines the procedure for installing an AR700 Series router. ■ The AR700 Series Router User Guide, which provides an introduction to the router and its software. ■ The Quick Start Guide for your router, which provides introductory information on network connections.
Need help?
Do you have a question about the AR700 SERIES and is the answer not in the manual?
Questions and answers