MAR, 2000
FACTORY RESET
1. Press [UTILITY].
2. Press the [
] cursor key to show the "UTIL2" screen.
fig_fact1.eps
3. Select "4:FACTORY RESET" with the cursor keys, then press [ENTER],
and the display will show the following screen.
fig_fact2.eps
4. Press [ENTER].
•
If Internal Write Protect is ON, a warning will be issued and then the
display will show the following screen.
fig_fact3.eps
Press [DEC/-] to turn Internal Write Protect OFF, then press [ENTER],
and the display will return to showing the screen in step 3.
•
If Internal Write Protect is OFF, the display will show the following
screen.
fig_fact4.eps
Factory reset is performed when [ENTER] is pressed.
VERSION UP
The XV-88 uses a flash memory for the program ROM. The version of the
program ROM can be upgraded by loading MIDI data into the XV-88.
After upgrading the version, factory reset must be performed. If important
data is written in the user memory, save the data on a card before
upgrading the version.
Required Items
•
XV-88 Ver. Up Disk (2DD: Two disks) (#17048530)
•
Sequencer capable of regenerating SMF (Also possible using a syn-
thesizer with a sequencer)
•
MIDI cable
ファクトリーリセットの方法
ファクトリーリセットの方法
ファクトリーリセットの方法
ファクトリーリセットの方法
1. [UTILITY] を押します。
2. カーソルキー [ ↓ ] を押して、 「UTIL2」の画面にします。
3. カーソルキーで「4:FACTORY RESET」を選び、[ENTER] を押すと、以下の
ような画面になります。
4. [ENTER] を押します。
・ Internal Write Protect が ON の場合、警告の後、以下の画面が表
示されます。
[DEC/-] を押して Internal Write Protect を OFF にしてから [ENTER] を
押すと、3 の画面に戻ります。
Å@
・ Internal Write Protect が OFF の場合は、以下の画面になります。
[ENTER] を押すとファクトリーリセットが実行されます。
フラッシュ ROM のバージョンアップの方法
フラッシュ ROM のバージョンアップの方法
フラッシュ ROM のバージョンアップの方法
フラッシュ ROM のバージョンアップの方法
XV-88 は、プログラム ROM にフラッシュメモリを使用しています。
これらは外部から MIDI データを送り込むことによりバージョンアップ
できます。なお、バージョンアップ後は必ずファクトリーリセットを行
う必要があります。ユーザーメモリに大切なデータが書込まれている場
合は、データを保存( 「ユーザーデータのセーブとロード」参照)して
からバージョンアップ作業を行なって下さい。
◎ ◎ ◎ ◎
用意するもの
用意するもの
用意するもの
用意するもの
・ XV-88 Ver.Up Disk (2DD:2 枚組)(#17048530)
・ SMF の再生できるシーケンサー (XP-80 等のシーケンサー付きシンセ
サイザーでも可)
・ MIDI ケーブル
Version Up Procedure
1. Connect the MIDI cable from MIDI OUT of the external sequencer to
MIDI IN of the XV-88.
2. Turn on the XV-88 power while holding down [DEC/-] and [A] at the
same time, and the display will show the following MIDI update screen.
fig_update1.eps
3. Press [INC/+], and the display will show the following screen, waiting
for the reception of MIDI data.
fig_update2.eps
4. After confirming the display in step 3, regenerate all the "..mid" files in
the XV-88 Ver. Up Disks 1 and 2 from the external sequencer (the
order does not matter). During the reception of MIDI data, the "MIDI
message" LED blinks and the message "Waiting" changes to the mes-
sage "Receiv-ing."
When the data transfer of one file ends, the message "Waiting" will
appear on the display. Then regenerate the next file.
The use of a sequencer with a chain play function, such as the XP-80,
allows the version to be upgraded even more easily. Load and play the
".svc" file (chain file), and all the ".mid" files found on Disk 1 will be
auto-matically regenerated. When regenerating Disk 1 all ends,
replace with Disk 2 and play it again.
5. When the update ends normally, the display will show the following
screen and the [A] to [H] LED's will blink.
fig_update3.eps
6. After playing all the ".mid" files on the two Ver. Up Disks, turn off the
XV-88 power to exit VERSION UP.
7. Lastly, perform test mode. (See page 10.)
Be sure to test the following test items
•
Top page (Identifying the version number)
•
D Beam Adjustment
•
Bender/D Beam Test
•
Factory Reset
This completes the version up.
NOTES:
Number of SMF's
•
One SMF is created for one block of flash memory.
•
Thirty-two SMF's, p00001.mid to p00032.mid, are created.
•
Some files may be omitted depending on the size of the program.
•
SMF is always created in p00032.mid because checksum data is
placed in it.
Ending the update
•
When p00032.mid has been received, it is judged that all the update
data has been received.
•
Any block, which has not been updated at this point of time, will be
erased.
•
This is performed to properly control the checksum data in the exter-
nal ROM.
•
Therefore, some blocks only cannot be updated.
XV-88
◎ ◎ ◎ ◎
バージョンアップの方法
バージョンアップの方法
バージョンアップの方法
バージョンアップの方法
1. MIDI ケーブルを外部シーケンサーの MIDI OUT から XV-88 の MIDI
IN に接続します。
シーケンサーで SMF をチェインプレイできるように設定します。
2. [DEC/-] と [A] を同時に押しながら電源を入れると、以下のような
MIDI アップデート画面に入ります。
3. [INC/+] を押すと次の表示になり、MIDI データの受信待ち状態になります。
4. 3. の表示を確認した後、XV-88 Ver.Up Disk 1,2 の中にある全ての
".mid" ファイルを外部シーケンサから再生します。 (順序は問いませ
ん)MIDI データ受信中は [MIDI message] の LED が点滅し、
「Waiting」の表示が「Recieving」に変わります。1 つのファイルの
データ転送が終了すると、表示が「Waiting」になりますので、続け
て次のファイルを再生して下さい。
なお、XP-80 等のチェインプレイ機能を持つシーケンサーを用いる
と、より簡単にバージョンアップができます。Disk 1 の中にある
".svc" ファイル(チェインファイル)をロードし、PLAY すると、
Disk 1 の中の全ての ".mid" ファイルを自動的に再生します。Disk 1
の再生が全て終了したら、Disk 2 に入れ替えて再び PLAY します。
5. アップデートが正常に終了すると次の表示になり、[A] -- [H] の
LED が点滅します。
6. 2 枚の Ver.Up Disk の全ての ".mid" ファイルをプレイし終わったら、
電源を切りアップデートを終了します。
7. 最後にテストモードを行います。 (P10 参照)以下の項目は必ず行っ
て下さい。
・ TOP Page(ROM のバージョンの確認を行います。 )
・ D Beam Adjustment
・ Bender/D BEAM Test
・ Factry Reset
以上でバージョンアップは終了です。
◎ ◎ ◎ ◎
注意点
注意点
注意点
注意点
SMF の数について
SMF の数について
SMF の数について
SMF の数について
・ SMF は Flash Memory の 1 ブロックに対して、一つ作られます。
・ p00001.mid -- p00032.mid の 32 個の SMF が作られます。
・ プログラムのサイズによっては、途中のファイルが抜ける事があります。
・ p00032.mid にはチェックサムデータが置かれますので必ず作られます。
アップデートの終了について
アップデートの終了について
アップデートの終了について
アップデートの終了について
・ p00032.mid を受信し終えると、全アップデートデータを受信した
と判断しています。
・ この時点でアップデートされなかったブロックは消去します。
・ これは外 ROM のチェックサムデータを正しく管理するためです。
・ 従って一部のブロックのみをアップデートすることはできません。
9