Table of Contents
Related Manuals for Boser HS-7250
Summary of Contents for Boser HS-7250
- Page 1 HS-7250/HS-7250M HS-7650/HS-7650M Intel® Pentium® M/Celeron®M/ ULV Intel® Celeron® M processor PCI-ISA/ISA Bus Single Board Computer •CompactFlash•DDR• •DVI-I/CRT/LVDS•Dual LAN• •Audio•ATA/33/66/100• •RS-232/422/485•USB2.0• •WDT•H/W Monitor•...
- Page 2 Unauthorized reproduction, transmission, translation, and storage of any form and means (i.e., electronic, mechanical, photocopying, recording) of this document, in whole or partly, is prohibited, unless granted permission by BOSER Technology Co., Ltd. reserves the right to change or improve the contents of BOSER Technology Co., Ltd.
-
Page 3: Table Of Contents
Table of Contents Chapter 1 General Description ........1 1.1 Major Features ............... 2 1.2 Specifications ................ 3 1.3 Board Dimensions..............4 Chapter 2 Unpacking ..........5 2.1 Opening the Delivery Package..........5 2.2 Inspection................5 Chapter 3 Hardware Installation ......7 3.1 Before Installation ..............7 3.2 Board Layout ................. - Page 4 Chapter 4 Award BIOS Setup ......... 23 4.1 Starting Setup..............23 4.2 Using Setup ................. 24 4.3 Main Menu................25 4.4 Standard CMOS Features........... 26 4.5 Advanced BIOS Features ........... 27 4.6 Advanced Chipset Features..........28 4.7 Integrated Peripherals ............29 4.8 Power Management Setup ..........
- Page 5 Declaration of Conformity -- CE Mark BOSER Technology hereby acknowledges that compliance testing in accordance with applicable standards of the EU’s EMC Directive, 89/336/EEC, was successfully completed on a sample of the equipment identified below: Equipment Class: Information Technology Equipment...
-
Page 6: Safety Instructions
Safety Instructions Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions: Do not remove boards or integrated circuits from their anti-static packaging until you are ready to install them. Before handling a board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. -
Page 7: Chapter 1 General Description
I/O with CF, DVI-I/CRT/LVDS, dual LAN, audio, COM, and USB2.0 interfaces. Its onboard ATA/33/66/100 to IDE drive interface architecture allows the HS-7250/HS-7650 series to support data transfers of 33, 66 or 100MB/sec. to one IDE drive connection. The HS-7250/HS-7650 supports Intel® Pentium® M/Celeron® M processor 1.3~2.0GHz, and HS-7250M/HS-7650M supports ULV Intel®... -
Page 8: Major Features
1 x DIMM up to 1GB DDR SDRAM Intel® 852GME/ICH4 system chipset (HS-7250/HS-7650) Intel® 852GM/ICH4 system chipset (HS-7250M/HS-7650M) Intel® 852GME integrated VGA for CRT & LVDS (HS-7250/HS-7650) Intel® 852GM integrated VGA for CRT & LVDS (HS-7250M/HS-7650M) 2 x Intel® 10/100 Mbps Ethernet AC’97 audio codec... -
Page 9: Specifications
HS-7250M/HS-7650M provides: ULV Intel® Celeron® M processor 600MHz/512K Front Side Bus: HS-7250/HS-7650 supports 400/533MHz FSB (From HS-7250 PCB v1.3 and later version, HS-7650 PCB v1.1 and later version can supports 533MHz FSB) HS-7250M/HS-7650M supports 400MHz FSB BIOS: Award PnP Flash BIOS Chipset: Intel®... -
Page 10: Board Dimensions
Display Chipset Intel® 852GME (HS-7250/HS-7650) Intel® 852GM (HS-7250M/HS-7650M) LVDS 18-bit single/dual-channel DVI Chipset Chrontel 7301 (option) Resolution CRT Mode: 1600 x 1200 Audio Chipset RealTek ALC202A Audio Interface (w/pin header) MIC In, Line Out Ethernet Chipset Intel® 82562ET and 82551ER dual 10/100 Mbps LAN... -
Page 11: Chapter 2 Unpacking
Chapter 2 Unpacking Opening the Delivery Package The HS-7250/HS-7650 series is packed in an anti-static bag. The board has components that are easily damaged by static electricity. Do not remove the anti-static wrapping until proper precautions have been taken. Safety Instructions in front of this manual describe anti-static precautions and procedures. - Page 12 Cables Package Description QTY. DMA100 40P(2.54-pitch) flat cable FDC 34P(2.54-pitch) flat cable 1-to-2 USB cable with bracket SPK 8P(2.54-pitch) phone jack x 2 2RS-232 cable with bracket (2.0-pitch) 5P ATX Power control cable ATX Ctrl cable 20P-5P+4P 1-to-2 PS/2 Mini DIN KB/MS cable (only for PS/2 Version) If you want to use DVI-I device under WIN98 or WINNT, please purchase this cable separately.
-
Page 13: Chapter 3 Hardware Installation
Keep the manual and diskette in good condition for future reference and use. NOTE: Since AD22 has been assigned for ISA bridge at HS-7250/ HS-7250M, please make sure do not use this address for other PCI cards to avoid confliction. In order to get detailed information,... -
Page 14: Board Layout
Board Layout Jumper List Jumper Default Setting Setting Page Onboard LAN 2 Enabled/Disabled Select: Short 1-2 Enabled Clear CMOS: Normal Operation Short 1-2 Short 3-4 System Frequency Select: 400MHz Short 1-2 COM 2 Use RS-232 or RS-422/485 Select: Open RS-232 AT/ATX Power Mode Select: AT Short 1-2... -
Page 15: Connector List
2.0GHz, Pentium® M processor 745 1.8GHz, Celeron® M processor 370 1.5GHz, and Celeron® M processor 1.3GHz. The HS-7250M/ HS-7650M embedded with ULV Intel® Celeron® M processor 600MHz/512K. HS-7250/HS-7650 provides 533MHz, if you want to use 533MHz FSB processor, please set JP3/JP6, and JP3 is only for HS-7250/ HS-7650. -
Page 16: System Memory
400MHz FSB (default) Short 3-4 Short 1-2 NOTE: HS-7250 supports 533MHz FSB from PCB v1.3 and later version. HS-7650 supports 533MHz FSB from PCB v1.1 and later version. Heat Sink Installation (more detail please see Appendix A) Please smear the heat sink paste over CPU and 852GM uniformly. -
Page 17: Vga Controller
7301 for DVI-I display, supporting up to 1600 x 1200. (DVI-I connector is optional) HS-7250/HS-7650 series also provides 18-bit single/dual-channel LVDS panel display interface. The HS-7250/HS-7650 series provides three methods of connecting VGA device. CN12 offers a single standard CRT connector (DB15), or CN9 offers DVI-I connector, or... - Page 18 CN9: DVI-I Connector PIN Description PIN Description TDC2J TDC2 DDCCLK DDCDATA VSYNC TDC1J TDC1 VCC5 HPDET TEC0- TDC0 TLC1 GREEN BLUE HSYNC PANEL2/PANEL1: LVDS Interface Connector PIN Description PIN Description B0(-)/A0(-) B0(+)/A0(+) B1(-)/A1(-) B1(+)/A1(+) B2(-)/A2(-) B2(+)/A2(+) CLK(-) CLK(+) Reserved Reserved NOTE: LVDS cable should be produced very carefully.
-
Page 19: Pci E-Ide Drive Connector
BK_EN LCD_EN PCI E-IDE Drive Connector IDE2 and IDE1 are standard 2.54-pitch 40-pin connector which support up to 4 ATA/33/66/100 IDE drives can be connected to the HS-7250/HS-7650 series via IDE2 and IDE1. IDE2/IDE1: Primary/Secondary IDE Connector Description Description Reset... -
Page 20: Floppy Disk Drive Connector
Floppy Disk Drive Connector The HS-7250/HS-7650 uses a standard 34-pin connector, FD1, for floppy disk drive connection. A total of two FDD drives may be connected to FD1 at any given time. FD1: FDD Connector PIN Description PIN Description DRVDEN0... -
Page 21: Ethernet Connector
*2: 4-wires point-to-point full duplex function 4-wires point-to-point full duplex RS-422/485 Typical RS-485 2-wires Mutildrop Network 3.11 Ethernet Connector The HS-7250/HS-7650 series provides two external RJ-45 interface connectors. Please refer to the following for its pin information. JP1: Onboard LAN 2 Enabled/Disabled Select Options... -
Page 22: Usb Connector
R/C GND R/C GND R/C GND 3.12 USB Connector The HS-7250/HS-7650 series provides one 8-pin internal connector at location US1, and one external USB2.0 ports at US2, for three USB2.0 ports to the HS-7250/HS-7650 series. NOTE: US2 and KB1 can not use at the same time. -
Page 23: Cmos Data Clear
3.13 CMOS Data Clear The HS-7250/HS-7650 series has a Clear CMOS jumper on JP2. JP2: Clear CMOS Options Settings Normal Operation (default) Short 1-2 Clear CMOS Short 2-3 IMPORTANT: Before turn on system, please set JP2 to Short 1-2 for normal operation. -
Page 24: Keyboard/Mouse Connectors
Options Settings AT (default) Short 1-2 Open NOTE: JP7 only for HS-7250/M PCB v1.3 and HS-7650/M PCB v1.1 and later version. FN2: Fan Power Connector Description +12V Fan In 2 Connector FN2 onboard HS-7250/HS-7650 series is a 3-pin fan power output connector. -
Page 25: System Front Panel Control
Mouse Clock 3.16 System Front Panel Control The HS-7250/HS-7650 series has one LED at location CN3 that indicates the system front panel status. This visual feature of the HDD LED may also be connected to and external HDD LED via connector CN8. -
Page 26: Audio Connectors
User can also use AL, 00H’s defined time for reset purposes, e.g.00H for Disable, 01H = 1sec, 02H=2sec….FFH=255sec. 3.18 Audio Connectors The HS-7250/HS-7650 series has an onboard AC97 3D audio controller. The following tables list the pin assignments of the Line In/Line Out connector. -
Page 27: Compactflash Connector
AOUTR MIC IN 3.19 CompactFlash Connector The HS-7250/HS-7650 series also offers a Type I/II CompactFlash connector which is IDE interface located at the solder side of the board. The designated CN13 connector, once soldered with an adapter, can hold CompactFlash cards of various sizes. Please turn off the power... -
Page 28: Pin Description
CN13: CompactFlash Connector Description Description IDE_PDD3 IDE_PDD4 IDE_PDD5 IDE_PDD6 IDE_PDD7 IDE_PDCS1# +3.3V IDE_PDA2 IDE_PDA1 IDE_PDA0 IDE_PDD0 IDE_PDD1 IDE_PDD2 IDE_PDD11 IDE_PDD12 IDE_PDD13 IDE_PDD14 IDE_PDD15 IDE_PDCS3# IDE_PDIOR# IDE_PDIOW# +3.3V INT_IRQ15 +3.3V +3.3V RESET# IDE_PDIORDY CF_PDERQ CF_REGB IDE_ACTP# DETECT IDE_PDD8 IDE_PDD9 IDE_PDD10 Inserting a CompactFlash card into the adapter is not a difficult task. The socket and card are both keyed and there is only one direction for the card to be completely inserted. -
Page 29: Chapter 4 Award Bios Setup
Chapter 4 Award BIOS Setup The HS-7250/HS-7650 series uses Award BIOS for the system configuration. The Award BIOS setup program is designed to provide the maximum flexibility in configuring the system by offering various options that could be selected for end-user requirements. This chapter is written to assist you in the proper usage of these features. -
Page 30: Using Setup
Using Setup In general, you use the arrow keys to highlight items, press <Enter> to select, use the <PageUp> and <PageDown> keys to change entries, and press <Esc> to quit. The following table provides more detail about how to navigate in the Setup program using the keyboard. Move to previous item ↑... -
Page 31: Main Menu
Main Menu Once you enter the Award BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press <Enter> to enter the sub-menu. Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Frequency/Voltage Control... -
Page 32: Standard Cmos Features
Standard CMOS Features The standard CMOS is used for the basic hardware system configuration. The main function is for Data/Time and Floppy/Hard Disk Drive settings. Please refer to the following screen for the setup. When the IDE hard disk drive you are using is larger than 528MB, you must set the HDD mode to LBA mode. -
Page 33: Advanced Bios Features
Advanced BIOS Features This section allows you to configure your system for the basic operation. You have the opportunity to select the system’s default speed, boot-up sequence, keyboard operation, shadowing and security. Phoenix - AwardBIOS CMOS Setup Utility Advanced CMOS Features CPU Feature [Press Enter] Item Help... -
Page 34: Advanced Chipset Features
Advanced Chipset Features This section allows you to configure the system based on the specific features of the installed chipset. This chipset manages bus speeds and the access to the system memory resources, such as DRAM and the external cache. It also coordinates the communications between the conventional ISA and PCI buses. -
Page 35: Integrated Peripherals
Flat Panel Type Type 1 640 x 480 18-bit Single Channel Type 2 800 x 600 18-bit Single Channel Type 3 1024 x 768 18-bit Single Channel Type 4 1280 x 1024 18-bit Dual Channel Type 5 1440 x 1050 18-bit Dual Channel Type 6 1440 x 1050... - Page 36 Phoenix - AwardBIOS CMOS Setup Utility OnChip IDE Device On-Chip Primary PCI IDE [Enabled] Item Help IDE Primary Master PIO [Auto] IDE Primary Slave PIO [Auto] IDE Primary Master UDMA [Auto] IDE Primary Slave UDMA [Auto] On-Chip Secondary PCI IDE [Enabled] IDE Secondary Master PIO [Auto]...
-
Page 37: Power Management Setup
Power Management Setup The power management setup allows user to configure the system for saving energy in a most effective way while operating in a manner consistent with his owns style of computer use. Phoenix - AwardBIOS CMOS Setup Utility Power Management Setup Power-Supply Type [ATX]... -
Page 38: Pnp/Pci Configurations
PnP/PCI Configurations This section describes the configuration of the PCI bus system. Peripheral Components Interconnect (PCI), is a system that allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings. -
Page 39: Pc Health Status
4.10 PC Health Status Phoenix - AwardBIOS CMOS Setup Utility PC Health Status CPU Warning Temperature [Disabled] Item Help Current CPU Temperature Current SYSTEM Temperature Current CPUFAN Speed VCORE +3.3V +12V VBAT(V) Shutdown Temperature [Disabled] ↑↓← →: Select Item +/-/PU/PD: Value F10: Save Esc: Quit F1: General Help... - Page 40 This page is the blank page.
-
Page 41: Chapter 5 Software Utilities
Chapter 5 Software Utilities This chapter contains the detailed information about installation procedures of chipset, VGA, LAN, audio and other drivers. The utility CD disk that comes with the package contains an auto-run program that invokes the installation programs for the chipset, VGA, LAN and audio drivers. - Page 42 Immediately after clicking the Chipset button in Step 1, the program launches the Setup that will assist you in the installation process. Click on the Next > button to proceed. The License Agreement dialog box then appears on the screen. Choose Yes to proceed.
- Page 43 When the Readme Information dialog box pops up , just click on the Next > button to proceed. Once the Install Shield Wizard finishes updating your system, it will prompt you to restart the computer. Tick on the Yes, I want to restart my computer now followed by a click on the Finish button to reboot.
-
Page 44: Vga Driver Installation
VGA Driver Installation Insert Utility CD Disk into your CD-ROM drive. The main menu will pop up as shown below. Select on the VGA button to launch the installation program. When the dialog box below appears, make sure you close all other Windows applications then click on the Next >... - Page 45 The Intel® OEM Software License Agreement dialog box appears on the screen. Choose Yes to proceed. Once the setup program finishes copying files into your system, it will prompt you to restart the computer. Tick on the Yes, I want to restart my computer now followed by a click on the Finish button to reboot.
-
Page 46: Lan Driver Installation
LAN Driver Installation 5.3.1 Install 82562ET Driver Insert Utility CD Disk into your CD-ROM drive. Click 82562 to install 82562 LAN driver. Select on the LAN button to launch the installation program. The Intel® OEM Software License Agreement dialog box then appears on the screen, choose Yes to proceed. - Page 47 Choose driver install location. (ex: c:\IntelPRO) When the dialog box below appears, make sure you close all other Windows applications the click on the Install Base Driver button to proceed. When setup is finished, press Exit and reboot your computer to take the effect.
- Page 48 5.3.2 Install 82551ER Driver With the Utility CD Disk still in your CD-ROM drive, right click on “My Computer” icon from the Windows menu. Select on System Properties and then proceed to the Device Manager from the main menu. Select on Other Devices that has exclamation mark with Ethernet controller from the list of devices then double-click on...
- Page 49 The Ethernet Controller Properties screen will appears, allow you to update the driver. Select Driver tab. When the dialog box below appears, make sure you close all other Windows applications, and choose “Yes, this time only” then click on the Next > button to proceed.
- Page 50 Select the “Install the software automatically (Recommended)” button once the following screen appears, Click on the Next > to proceed. Click on the Continue Anyway.
-
Page 51: Audio Driver Installation
Once the Hardware Update Wizard completes the operation and update of your 82551ER driver. Click on the Finish button to complete the installation process. Audio Driver Installation Insert Utility CD Disk into your CD-ROM drive. The main menu will pop up as shown below. Select on the Audio button to launch the installation program. - Page 52 When the dialog box below appears, make sure you close all other Windows applications then click on the Next > button to proceed. Once the Install Shield Wizard completes the operation and update of your AC97 driver, it will ask you to remove disks form their drives, and prompt you to restart your system.
-
Page 53: Appendix A Assembly Sop Of The Thermal Sink
Appendix A Assembly SOP of Thermal Sink A heat sink with a fan, a bag of heat sink paste and a bag of screws & washers A bag of heat sink paste Spread the heat sink paste on the CPU in the red circle... - Page 54 Unscrew four screws in the red circles Remove the fan from the heat sink Screw nuts...
- Page 55 Put the two screw nuts in the red circles Put the heat sink shown in the red circle on the mainboard Screws and washers...
- Page 56 Screw the mainboard and the heat sink from the rear side of the mainboard in the red circles The front side of the mainboard screwed with the heat sink A fan...
- Page 57 Screw the fan with four screws in the red circles on the heat sink Two clips Fasten the heat sink and the mainboard with a clip on the left side of the heat sink...
- Page 58 Fasten the heat sink and the mainbaord with a clip on the right side of the heat sink Picture 1 of the finished product Picture 2 of the finished product...
- Page 59 Picture 3 of the finished product...
- Page 60 This page is the blank page.
Need help?
Do you have a question about the HS-7250 and is the answer not in the manual?
Questions and answers