Page 1
TEL: +353 (01) 8372445 FAX: +353 (01) 8571685 Thank You for purchasing Reliable Security Products Ltd. SmartWatch™. Before operating the system, please read this User’s Manual thoroughly and retain it for future reference. The manufacturer reserves the right to revise and improve its products. Therefore the technical specifications are subject...
The following accessories are supplied with the SWE Series digital video recorder. If any of these items is missing or damaged, notify your dealer immediately. Keep the packing utilities for moving or storage purposes afterwards. SWE4 Series: SWE8 and SWE16 Series:...
Rubber Mount Set Rack Mounts and Screws 3. CONNECTING YOUR SMARTWATCH™ UNIT Install the SWE Series on a flat surface. If required, attach the rubber mount for installation. If a 19-inch rack is used, it is recommend to install the system on a shelf and use 2.5~3U (1U=1.75 inch or 4.45cm) space for proper ventilation.
Page 5
4 4 4 4 SWE8 and SWE16 Series Name Functions Camera Input (BNC) Connect to Camera (supports NTSC/PAL) Camera images of each channel will be outputted as is (also used when the LOOP OUT corresponding image is required for other product) Connect to the main monitor for camera image surveillance / management / MON OUT playback...
Page 6
5 5 5 5 Name Functions Power Input Connect main power cable Select NTSC / PAL Select the signal system (NTSC/PAL) SENSOR Input Connect 1~16 external input sensors (supports N/O or N/C) USB Port Connect USB device LAN Port RJ-45 socket for 10/100 Ethernet connection S-Video Output Secondary main monitor output Serial Port...
UNIT YOUR SMART WATCH YOUR SMART WATCH UNIT UNIT 4.1 Front Panel 4.1.1. SWE4 Series Button Function CD-RW Built-in CD-RW for recorded image backup. Network LED The LED is lit while the network client(s) (RemoteAgent) is connected to the system.
Page 8
7 7 7 7 4.1.2. SWE8 and SWE16 Series Buttons Functions Power Button Use to turn the Power On/Off. Power LED Shows the Power status of the system (GREEN: Working, RED: Stand-by). Shows if the camera image is being stored into or retrieved from the HDD (Hard HDD LED Disk Drive).
ID has yet been programmed). You will be prompted to enter an administrator password. If this is the first time the unit has been powered up, just press the [ENTER] button. On the SWE4 Series, the [ENTER] button is the circular button at the centre of the 1, 2, 3, 4 keys.
Page 11
It is important at this stage to set the ID for the IR Remote Controller. Every function of the DVR can be controlled remotely by using the IR Remote Controller. Some functions on the SWE4 Series are easier to select by using it as dedicated buttons are assigned for each function.
Page 12
Networks: Set the network Connection Type Select the connection type. environment of the system. Host Address Input the IP address assigned to SWE (SWE4 Series) / Series system. IP Address (SWE8 and SWE16 Series) Subnet Mask Subnet Mask address recognizes the subnet to which the system belongs.
Page 13
Main Sub Classification Setting Category Explanation Classification usage. 720x576 Set the speed rate (frame per second) to record the image inputted through connected camera. 640x288 Set the speed rate (frame per second) to record the image inputted through connected camera. 352x288 Set the speed rate (frame per second) to record the image inputted through...
Install the RemoteAgent Software on the PC where you want to view the DVR images. You can connect to the DVR via LAN or DHCP (only for the SWE4 Series). To make the connection to a DVR, first you have to register the DVR. Click the [CONNECT] button or right click and chose Open Site/File (CTRL+O).
Page 15
Functions Functions Description Description Functions Functions Description Description Display current or registered images from selected channels (maximum 16 Channel Screen channels) on the split-screen mode. Register the User IP to the connected DVR and shows each event on the Event Panel/Intelli-Search Panel DVRs (system booting, recording system, stop recording, etc.).