Blower Speed Selection - Rheem R95P Installation Instructions Manual

TABLE 17
IR FLOW PERFORM NCE – (-)95P SERIES MODELS
Motor HP [W]
Model Blower Size
IN [MM]
(-)95PA 1/4 [187]
0401 11 x 7
317MSA [279 x 178]
(-)95PA 1/2 [373]
0601 11 x 8
317MSA [279 x 203]
(-)95PA 1/2 [373]
0701 11 x 8
317MSA [279 x 203]
(-)95PA 3/4 [559]
0851 11 x 10
521MSA [279 x 254]
(-)95PA 3/4 [559]
1001 11 x 10
521MSA [279 x 254]
(-)95PA 3/4 [559]
1151 11 x 11
524MSA [279 x 279]
*Factory Setting For Heat
All shaded cells are valid heating settings. Do not use speed taps and/or static pressures which do not fall into the shaded cells on this table.
The furnace controls have four active quick connect termi-
nals for connecting the motor speed leads. These are:
1. FAN — motor runs on this speed when the thermostat
is in the "FAN ON" position.
2. COOL — connect desired cooling speed.
3. HEAT — connect desired heating speed.
4. H/C (for heat/cool) — connect desired speed when
heating and cooling speed are the same.
In addition to the active motor terminals, there are two
motor parking terminals (labeled M1 and M2) available for
placing any unused motor taps. All unused motor taps
should be connected to either M1 or M2. These terminals
(M1 and M2) will not be energized under any condition.
IMPORTANT: Do not connect any motor speeds to "HEAT"
and/or "COOL" if you use the "HEAT/COOL" terminal.
Speed Tap 0.1 [0.02] 0.2 [0.05]
Low 732 695
Med. Lo 875 845
Med. Hi* 1073 1049
High 1279 1239
Low 830 793
Med. Lo 940 908
Med. Hi* 1168 1139
High 1421 1385
Low 852 827
Med. Lo 986 955
Med. Hi* 1238 1211
High 1493 1452
Low 1313 1275
Med. Lo 1488 1452
Med. Hi* 1732 1704
High 1983 1929
Low 1329 1313
Med. Lo 1535 1498
Med. Hi* 1796 1748
High 2019 1961
Low 1249 1234
Med. Lo 1440 1429
Med. Hi* 1770 1750
High 2123 2077
CFM ir Delivery
External Static Pressure, "W.C. [kPa]
0.3 [0.07] 0.4 [0.10] 0.5 [0.12]
669 639 605
820 792 766
1004 975 943
1213 1174 1121
755 705 654
875 821 766
1109 1060 1010
1349 1291 1232
802 752 701
923 883 843
1183 1139 1094
1410 1364 1318
1236 1221 1184
1415 1384 1328
1676 1630 1579
1874 1810 1742
1296 1260 1224
1461 1422 1382
1700 1656 1612
1903 1843 1782
1219 1183 1146
1417 1381 1344
1730 1696 1662
2031 1983 1934
5. If heating and continuous fan speed are the same,
"piggyback" jumper across "FAN" and "HEAT" termi-
nals.
If cooling speed and fan speed are desired to be the same,
this may be accomplished by not connecting "Y" to the in-
tegrated furnace control.
IMPORTANT: If desired for cool, fan and heat to all be
the same speed, then "piggyback" jumper "H/C" to
"FAN" and do not connect "Y" to the integrated fur-
nace control. Do not connect anything to "Heat" or
"Cool."
See selection titled "Field Selections – Dipswitches" for
setting the heating and cooling blower off delay times.
0.6 [0.15] 0.7 [0.17] 0.8 [0.19]
547 512 487
726 659 605
900 864 798
1069 1033 980
599 544 496
710 653 584
942 874 802
1147 1062 976
662 623 580
790 737 686
1036 978 897
1257 1195 1084
1141 1098 1053
1279 1229 1170
1498 1417 1343
1663 1583 1477
1171 1117 1049
1325 1268 1203
1536 1460 1370
1687 1592 1489
1112 1078 1017
1313 1281 1221
1611 1559 1463
1856 1777 1665
93