Blower Speed Selection - Rheem 801S Series Installation Instructions Manual

TABLE 12
AIR FLOW PERFORMANCE – (-)801S/(-)801P & (-)(-)80MSS/(-)(-)80MSP SERIES MODELS
Motor HP
Model Blower Size,
IN.
(-)801SA050314MSA
1/3
(-)801PA050314MSA
(-)(-)80MSS050A30SA
11 x 6
(-)(-)80MSP050A30SA
(-)801SA075417MSA
1/2
(-)801PA075417MSA
(-)(-)80MSS075B30SA
11 x 7
(-)(-)80MSP075B30SA
(-)801SA100521MSA
1/2
(-)801PA100521MSA
(-)(-)80MSS100C40SA
11 x 10
(-)(-)80MSP100C40SA
(-)801SA125524MSA
3/4
(-)801PA125524MSA
(-)(-)80MSS125D50SA
11 x 10
(-)(-)80MSP125D50SA
(-)801SA150524MSA
3/4
(-)801SA150524MSA
(-)(-)80MSS150D50SA
11 x 10
(-)(-)80MSP150D50SA
NOTE: Shaded data is factory heating tap.
BLOWER SPEED SELECTIONS
The UT Electronic Controls control boards have four quick con-
nect terminals for connecting the motor speed leads. These are:
1. FAN SPEED* — motor runs on this speed when the thermo-
stat is in the "FAN" position.
2. COOL — connect desired cooling speed.
3. HEAT — connect desired heating speed.
4. HEAT/COOL* — connect desired speed when heating and
cooling speed are the same.
CAUTION
DO NOT CONNECT ANY MOTOR SPEEDS TO "HEAT" OR
"COOL" IF YOU USE THE "HEAT/COOL" TERMINAL. DOING
SO WILL DAMAGE THE BLOWER MOTOR. UNUSED
MOTOR WIRE TAPS MUST BE CONNECTED TO PARKING
TERMINALS M1 AND M2 OF THE IFC, OR PROPERLY IN-
SULATED.
5. If heating and continuous speed are the same, jump across
"FAN" and "HEAT" terminals.
See Table 10 for instructions for setting the blower "OFF" timings.
46
Speed Tap 0.1 0.2
Low 823 803
Med. Lo 1030 1018
Med. Hi 1129 1132
High 1361 1353
Low 1229 1200
Med. Lo 1308 1267
Med. Hi 1553 1542
High 1969 1924
Low 1209 1182
Med. Lo 1438 1420
Med. Hi 1902 1883
High 2071 2037
Low 1358 1354
Med. Lo 1541 1517
Med. Hi 1799 1774
High 2015 1989
Low 1411 1395
Med. Lo 1606 1579
Med. Hi 1889 1891
High 2178 2160
CFM Air Delivery
External Static Pressure, " W.C.
0.3 0.4 0.5
787 732 718
1006 976 929
1112 1087 1054
1331 1297 1264
1181 1155 1120
1266 1233 1204
1516 1491 1451
1893 1840 1803
1131 1112 1051
1386 1350 1320
1844 1817 1753
2001 1962 1905
1331 13091 1250
1476 1453 1416
1746 1712 1691
1929 1902 1862
1370 1334 1310
1569 1537 1499
1849 1828 1764
2105 2067 2024
GAS FURNACE (DIRECT DRIVE)
INSTRUCTIONS FOR CHANGING
BLOWER SPEED
DISCONNECT THE ELECTRICAL SUPPLY TO THE FUR-
NACE BEFORE ATTEMPTING TO CHANGE THE BLOWER
SPEED. FAILURE TO DO SO CAN CAUSE ELECTRICAL
SHOCK RESULTING IN SEVERE PERSONAL INJURY OR
DEATH.
The blower motor is wired for blower speeds required for normal
operation as shown.
If additional blower speed taps are available (leads connected to
"M1" and "M2" on the electronic control), speeds may be changed
if necessary to fit requirements of the particular installation. Re-
connect the unused motor leads to "M1" or "M2." Check motor
lead color for speed designation.
Heating speeds should not be reduced where it could cause the
furnace air temperature to rise to exceed the maximum outlet air
temperature specified for the unit.
0.6 0.7 0.8
691 651 593
897 850 808
1028 971 919
1232 1164 1117
1078 1013 970
1176 1113 1062
1417 1358 1306
1728 1657 1570
976 929 867
1293 1248 1186
1700 1636 1547
1856 1807 1709
1224 1154 1089
1371 1339 1277
1629 1554 1495
1815 1742 1665
1252 1220 1150
1468 1407 1346
1717 1659 1609
1976 1916 1832