Table of Contents
Advertisement
Quick Links
7.0 – 10-Up Format Gutter Cut
Figure 4 shows the 10-Up Format Gutter Cut that is to be used in the GC10. There is a Card Template CD included with
your Model GC10 BCS to help lay out your personal business cards.
For the highest quality cards, the print MUST be parallel with the sheet and consistently repeatable, meaning that the print
must be in the same exact location every time.
251 Wedcor Avenue ¦ Wabash, Indiana 46992
Phone (260) 563-0641 ¦ Fax (260) 563-4575
Toll Free Phone (800) 225-5644 ¦ Email: info@martinyale.com
Website: www.martinyale.com
M-S027928
Figure 4
Model GC10 Single Pass Business Card Slitter
Installation, Operation & Maintenance Instructions
Specifications
Feeding Method
Speed
Sheet Capacity
Sheet Size
Paper Weight (cover stock)
(*will not do translucent stock)
Digital Counter
Electrical (USA)
Dimensions (LxWxH)
(with scrap drawer open)
Shipping Weight
Serial No. _________________
Introduction
Thank you for selecting the GC10 Single Pass Business Card Slitter. Your business card slitter, or BCS, and all the
components were 100% tested at our factory. We tested all critical operations, verifying that your machine is fully
functional and ready to operate.
Please read and understand this manual completely before attempting to operate this BCS. This will prevent common
problems and eliminate operator-associated errors. Understanding these instructions will provide years of excellent
performance from a quality machine.
Rev.4 1/29/13
Table of Contents
Continuous Top Feed
Introduction
2,400 Cards/Hour
Safety Notes
50 sheets
Initiation
8 ½" x 11"
65# to 100# (150 – 275 gsm)
6.0 pt. to 12 pt.
job & life count, resettable
115VAC 60 Hz, 1 Amp
21" x 22" x 14"
36" x 22" x 14"
97 lb.
7.0 – 10-Up Format Gutter Cut
Scope of Application:
The GC10 Single Pass Business Card Slitter is a machine for cutting
in the 10-up gutter cut format.
This unit should be fed with card stock!
Cutting other types of materials can cause injuries or may
damage the BCS (e.g. destruction of the unit)
Installation:
- Unpack and set the machine upright with the controls facing you.
- See Section 2.0 Machine Setup
The socket outlet shall be installed near the equipment and
shall be easily accessible!
Only operate this machine in an enclosed office environment.
Keep enough distance to the surroundings when installing the
machine.
Page 1
Page 1
Page 1
Page 2
Page 4
Page 4
Page 4
Page 4
Page 5
Page 5
Page 5
Page 5
Page 5
Page 5
Page 6
Page 6
Page 6
Page 6
Page 7
Page 8
Advertisement
Table of Contents
Related Manuals for Martin Yale GC10
Summary of Contents for Martin Yale GC10
- Page 1 Introduction Figure 4 shows the 10-Up Format Gutter Cut that is to be used in the GC10. There is a Card Template CD included with Thank you for selecting the GC10 Single Pass Business Card Slitter. Your business card slitter, or BCS, and all the your Model GC10 BCS to help lay out your personal business cards.
- Page 2 Power cord is not plugged in; Plug in the power cord; No LED indication; GC10 main power switch is off; Turn the switch on; Unit is not running Circuit breaker is tripped. Reset the circuit breaker.
- Page 3 Once the top cover is off, use a clean cloth or soft nylon brush along with Martin Yale Roller Cleaner or water and mild detergent to clean the black rubber wheels.
- Page 4 4.0 – General Operation The overall design of the GC10 allows an operator to put a stack of 50 sheets of 10-Up Format Gutter Cut card stock into the feed table, press run, and have a limited interaction with the machine. For a more complete knowledge of the GC10’s operation, read the following:...
Need help?
Do you have a question about the GC10 and is the answer not in the manual?
Questions and answers