Do you have a question about the 2101000 and is the answer not in the manual?
Questions and answers
Paul
May 19, 2025
How do I replace the line
1 comments:
Mr. Anderson
May 23, 2025
To replace the line on a GreenWorks 2101000:
1. Remove the spool from the spool cover. 2. Cut one 8-foot (3 meters) length of line and bend it in the middle. 3. Hook the center of the line into location 'd' on the spool. 4. Hold the spool by hub 'a' and wind both halves of the line in the direction of the arrow on the spool. 5. Place one side of the line into slot 'c' and the other side into slot 'b'. 6. Use notch 'e' to temporarily hold the line. 7. Align the line with the metal eyelets and insert it securely into the eyelets. 8. Press the spool cap onto the retainer until it clicks securely into place. Repeat for both sides.
Page 1
Top mount Curved Shaft Trimmer 2101000 Owner’s Manual TOLL-FREE HELPLINE: 1-888-90WORKS (888.909.6757) Read all safety rules and instructions carefully before operating this tool.
GENERAL SAFETY INSTRUCTIONS W A R N I N G Read and understand all instructions before using this product. Failure to follow all use without guard and handle in place. READ ALL INSTRUCTIONS • For safe operation, read and understand all instructions before using this product. Follow all safety instructions.
GENERAL SAFETY INSTRUCTIONS • Warning – To reduce the risk of electric shock - Use outdoor extension cords marked W-A, W, SW-A, SOW-A, STW-A, STOW-A, SJW-A, SJTW-A, or SJTOW-A. These cords are rated for outdoor use and reduce the risk of electric shock. •...
Page 5
GENERAL SAFETY INSTRUCTIONS of personal injury. • cut with the string head located over 30 in. (76 cm) or more above the ground. • Store idle appliances - When not in use, power head should be stored indoors in a dry, locked place out of the reach of children.
GENERAL SAFETY RULES W A R N I N G Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury. SAVE THESE INSTRUCTIONS • Read these instructions and the instructions for the power head thoroughly before using the straight shaft trimmer attachment.
SPECIFIC SAFETY RULES • • • Keep string head below waist level. Never cut with the string head located over 30 in. (76 cm) or more above the ground. • Clear the work area before each use. Remove all objects such as rocks, broken glass, nails, wire, or string which can be thrown or become entangled in the cutting line.
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING Indicates an imminently hazardous situation, which, if not avoided, DANGER will result in death or serious injury. Indicates a potentially hazardous situation, which, if not avoided, WARNING could result in death or serious injury.
Page 9
If you do not understand the warnings and instructions in the operator’s manual, do not use this product. Call GREENWORKS customer service for assistance. W A R N I N G The operation of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage.
ELECTRICAL EXTENSION CORDS When using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to handle the current the product will draw. An undersized cord will cause a drop in line voltage, resulting in overheating and loss of power. Use the chart to determine the minimum wire size required in an extension cord.
FEATURES KNOW YOUR PRODUCT(See Figure 1.) The safe use of this product requires an understanding of the information on the tool and in this operator’s manual as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operating features and safety rules, in both this manual and the operator’s manuals for all attachments that your are using with this power head.
ASSEMBLY UNPACKING This product requires assembly. • Carefully remove the product and any accessories from the box. Make sure that all items listed in the packing list are included. • Inspect the product carefully to make sure no breakage or damage occurred during shipping. •...
Page 13
ASSEMBLY INSTALLING CURVE SHAFT TO THE POWER HEAD(See Figure 2.) W A R N I N G Read and understand entire Operator’s Manual for each optional attachment used on this power head and follow all warnings and instructions. Failure to follow all instructions may result in W A R N I N G This electric power head is designed to be only used with the attachment models that are specified in this Operator’s Manual.
Page 14
ASSEMBLY ATTACHING THE FRONT HANDLE(See Figure 3.) FRONT HANDLE WING NUT BOLT WASHER Fig.3 Unplug the power head. Press the front handle onto the power head shaft so that the handle is angled toward the rear handle. Place the front handle along the power head shaft to a position that allows for comfortable operation.
OPERATION W A R N I N G Read and understand entire Operator’s Manual for each optional attachment used on this power head and follow all warnings and instructions. Failure to follow all instructions may result in W A R N I N G Do not allow familiarity with product to make you careless.
Page 16
OPERATION CONNECTING TO POWER SUPPLY(See Figure 5 -6.) The power head is designed with a cord retainer that prevents the extension cord from being pulled loose while using. • Form a loop with the end of the extension cord. • Insert loop portion of extension cord through opening in the bottom of the rear handle and place over cord retainer.
Page 17
OPERATION OPERATING THE POWER HEAD W A R N I N G Motor housing may become hot during operation. Do not rest or place your arm, hand, or any 14 (depending on attachment used) during trimmer operation with all body parts clear of motor housing (or as shown in the applicable attachment Operator’s Manual).
Page 18
OPERATION LINE TRIMMING CUT-OFF BLADE CUT-OFF BLADE Fig.9 CUTTING TIPS e 10. DANGEROUS CUTTING AREA DIRECTION OF ROTATION BEST CUTTING AREA • Avoid hot surfaces by always keeping the tool away from your body. (Proper operating position • Keep the trimmer tilted toward the area being cut; this is the best cutting area. •...
Page 19
OPERATION REMOVING AND INSTALLING THE SPOOL HEAD Fig.11.1 Fig. 11.2 1. To remove the spool head. Insert the end 2. While holding the screw driver with one of a suitably sized screwdriver into the spindle hand, turn the spool head counterclockwise locking hole to prevent the spindle from turning.
Page 20
OPERATION HOW TO REPLACE THE SPOOL REMOVE THE SPOOL COVER Stop the motor and disconnect the power source from the unit Press the spool retainer tabs 'A' on both sides of the spool retainer to release the spool cover. (This may take some presssure to release the tabs") Spool Retainer A:Tabs Spool Cover...
Page 21
OPERATION Fig.12.4 Fig.12.5 3. Pull the line off the notch(see fig.12.3) 4. Once the line is placed in the metal and place it securely into the metal eyelet. eyelets. Press the spool cap onto the Do for both sides of the spool head. retainer until it clicks securely into place.
Page 22
OPERATION HOW TO REPLACE THE LINE ) . . INSTALLING NEW LINE IN THE SPOOL · Remove the spool from the spool cover · Bend one 8’ length (3m) of line in the middle and hook the string in location ‘d’ ·...
MAINTENANCE W A R N I N G When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. W A R N I N G Always wear eye protection with side shields marked to comply with ANSI Z87.1, along with hearing protection.
MAINTENANCE W A R N I N G Before inspecting, cleaning, or servicing the machine remove power cord. Failure to follow these instructions can result in serious personal injury or property damage. GENERAL MAINTENANCE Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use.
MAINTENANCE NOTE: Do not use any strong detergents on the plastic housing or the handle. They can be damaged by certain aromatic oils such as pine and lemon, and by solvents such as kerosene. STORING THE POWER HEAD • Clean all foreign material from the product. •...
(4) years against defects in materials, parts or workmanship. GREENWORKS™, at its own discretion will repair or replace any and all parts found to be defective, through normal use, free of charge to the customer. This warranty is valid only for...
Need help?
Do you have a question about the 2101000 and is the answer not in the manual?
Questions and answers
How do I replace the line
To replace the line on a GreenWorks 2101000:
1. Remove the spool from the spool cover.
2. Cut one 8-foot (3 meters) length of line and bend it in the middle.
3. Hook the center of the line into location 'd' on the spool.
4. Hold the spool by hub 'a' and wind both halves of the line in the direction of the arrow on the spool.
5. Place one side of the line into slot 'c' and the other side into slot 'b'.
6. Use notch 'e' to temporarily hold the line.
7. Align the line with the metal eyelets and insert it securely into the eyelets.
8. Press the spool cap onto the retainer until it clicks securely into place. Repeat for both sides.
This answer is automatically generated