Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ovislink OV504R
Summary of Contents for Ovislink OV504R
-
Page 1: User Manual
OV504R（TR069） User manual Ver: 2.00... -
Page 2: Important Safety Instructions
OV504R User Manual Important Safety Instructions Please read these instructions carefully: Unplug the ADSL2+ Router Ethernet Adaptor from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Do not use the ADSL2+ Router Ethernet Adaptor near water. -
Page 3: Table Of Contents
Contents Chapter 1 Introduction ................1 Features ......................1 ADSL standard supports ................. 1 Encapsulation supports ................... 2 System requirements ..................2 LED status description..................3 Rear panel layout.................... 4 Chapter 2 Hardware Installation ............... 5 Chapter 3 Modem Parameters Setting ............6 Configuring computer network card IP address.......... -
Page 4: Chapter 1 Introduction
Chapter 1 Introduction The device is a well-designed high-speed ADSL modem/router Features • Full rate ADSL router, support Bridge/Router • Provides 24Mbps downstream and 1Mbps upstream • Maximum transmission range: 5.4 Kilometers • Four Ethernet ports, 10/100 Mbps Auto-MDI/MDIX • Friendly GUI for web configuration. -
Page 5: Encapsulation Supports
• ANSI T1.413 Issue 2 • ITU G.992.3(ADSL2) • ITU G.992.5(ADSL2+) Encapsulation supports • RFC 1483 bridge • RFC 1483 Router • Classical IP over ATM (RFC 1577) • PPP over ATM (RFC 2364) • PPP over Ethernet (RFC 2516) System requirements Recommended system requirements are: •... -
Page 6: Led Status Description
Encapsulation: VCMUX or LLC Protocol Standard User name Password Password protocol LED status description INDICATOR STATUS Description No power Power Power supplied Quick Blink DSL line is training ADSL DSL line is connected Data Blink DSL data transferring Ethernet connection is OK (4-1) Blink Ethernet data transferring... -
Page 7: Rear Panel Layout
Rear panel layout Interface Description SWITCH Power on/off switch POWER Plug in for power adaptor Modem Reset button Press and hold around 5~10s to reset the RESET hardware. The modem will auto restart. This action will recover the modem’s default configuration. Ethernet interface for connecting to Ethernet(1-4) computer or Switch... -
Page 8: Chapter 2 Hardware Installation
Chapter 2 Hardware Installation Please connect the device to you computer as follow: • If connecting to the splitter, connect the “Line” splitter to wall jack using one telephone cable • Use the other telephone cable to connect “MODEM” port of the splitter and “LINE”... -
Page 9: Chapter 3 Modem Parameters Setting
Chapter 3 Modem Parameters Setting Configuring computer network card IP address Configure your network card’s TCP/IP properties to Obtain an IP address automatically from modem, or set the computer’s IP with the same network mask of the modem.(For example: modem’s IP is 192.168.1.1/255.255.255.0, Then you can set computer’s IP to: 192.168.1.x/255.255.255.0. -
Page 10: Ethernet Over Atm (Rfc1483 Bridge) Setting
Here provide the most common RFC1483 Bridge and PPP over Ethernet (RFC2516) setting for reference. If you want to know more about other protocol, please contact your ADSL service provider for details Ethernet over ATM (RFC1483 Bridge) setting From the Home page, click on “Quick Setup ”, See the following:... - Page 11 2. Unselect the check box to enable DSL Auto-connect process. Set any PVC channel, Click on VPI/VCI, see the following: 3. Click the “Next” button, and you can set the encapsulation which get from your ADSL service provider, see the following: 4.
- Page 12 5. Click the “Next” button, configure the DSL Router IP Address and Subnet Mask for your Local Area Network (LAN) , please use the default configurations, see the following: 6. Click the “Next” button, make sure that the settings below match the settings provided by your ISP., see the following:...
-
Page 13: Ppp Over Ethernet (Rfc2516) Setting
7. Click the “Save/Reboot” button, save your configurations. NOTICE: If you select Dial-UP link, after configuring your ADSL modem, please install the third-party dial up program to access Internet (For example: Ethernet 300/Ethernet 500/WinPoet). If your system is WinXP, you can use its own Internet access program without any other additional programs. - Page 14 2. Unselect the check box to enable DSL Auto-connect process. This Quick Setup will guide you through the steps necessary to configure your DSL Router., and you can set the PVC which get from your ADSL service provider, see the following: 3.
- Page 15 4. Click the “Next” button, unenable IGMP Multicast, and enable WAN Service, see the following. 5. Click the “Next” button, Configure the DSL Router IP Address and Subnet Mask for LAN interface, please use the default configurations, see the following.
- Page 16 6. Click the “Next” button, make sure that the settings below match the settings provided by your ISP. see the following: 7. Click the “Save/Reboot” button, save your configurations, then finish the Setting for PPPoE.
-
Page 17: Tr069 Setting
TR069 setting Inform: Disable: modem cannot automatically send out the request to the TR069 server Enable :modem can automatically send out the request to the TR069 server， Select “Enable”, all items below are effective... - Page 18 Inform Interval: Each modem how many seconds sends out the connection request to the TR069 server ACS URL: the path of modem sending out the request the TR069 server ACS User Name:the username of modem logging in TR069 server ACS Password: the password of modem logging in TR069 server Connection Request User Name: the username of the TR069 server visits modem TR069 process.
-
Page 19: Chapter 4 Questions & Answers
Chapter 4 Questions & Answers Question: Why all LED indicators are off? Answer: Check the connection between the power adaptor and the power socket • Check the power switch is on or not Question: Why Ethernet LED is not lighting? Answer: •... - Page 20 Click start -> run (input ping demands)-> Ping 192.168.1.1 (MODEM IP address). If cannot reach the modem, please check following configuration: • The type of the network cable • The connection between the modem and computer • You computer’s TCP/IP configuration Question: How to load the default setting after incorrect configuration? Answer: Press “reset”...