Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ovislink OV303R2M
Summary of Contents for Ovislink OV303R2M
- Page 1 OV303R2M Bridge Modem （TR069） User Manual Ver: 1.10...
-
Page 2: Table Of Contents
Contents Chapter 1 Introduction .............1 1.1 Features.................1 1.2 Encapsulation support...........1 1.3 System requirements.............1 1.4 LED status description..........2 1.5 Rear panel layout ............2 Chapter 2 Hardware Installation ........4 Chapter 3 Parameters Setting...........5 3.1 Network adaptor TCP/IP configuration ......5 3.2 RFC 1483 Bridge dial-up..........9 Chapter 4 Questions &... -
Page 3: Chapter 1 Introduction
User manual Chapter 1 Introduction The device is the ADSL CPE (Customer Premise Equipment) with ATU-R module, which complies with various ADSL standards, and excellent interoperation. 1.1 Features Full rate ADSL modem Provide up to 24Mbps downstream and up to 1.2Mbps upstream. -
Page 4: Led Status Description
User manual 1.4 LED status description Indicator Status Description No power Power Power on Ethernet data transferring Blink Connected to the network card or DSL line is training Blink ADSL DSL line is connected DSL data transferring DATA Blink 1.5 Rear panel layout... - Page 5 User manual Interface Description Switch Power on/off switch Power Plug in for power adaptor Modem Reset button, switch off then press “reset” button and switch on 4s to reset the Reset hardware. The modem will auto restart. This action will recover modem’s default...
-
Page 6: Chapter 2 Hardware Installation
User manual Chapter 2 Hardware Installation Please connect your device to computer as following description: If connecting to the splitter, connect the “Line” splitter to wall jack using one telephone cable Use the other telephone cable to connect “MODEM” port of the splitter and “LINE”... -
Page 7: Chapter 3 Parameters Setting
User manual Chapter 3 Parameters Setting This section will be the guideline for connecting the device to the Internet. There are two ways to visit Internet via the device. 3.1 Network adaptor TCP/IP configuration Note: Please collect the necessary information including IP address /Gateway/DNS server from your ADSL service provider before you start to configure TCP/IP properties You can connect the device to Internet without dial-up (It depends on... - Page 8 User manual 3.1.2 Static IP configuration Take Windows 2000 as an example, the setting procedures in other operating systems are similar with the following description. In static IP address mode, if you have the information of the IP and DNS address, please follow below steps to configure the TCP/IP properties Step 1:...
- Page 9 User manual Step 2: Select Local Area Connections and open “Local Area connections Properties” window. Then double click Internet Protocol (TCP/IP).
-
Page 10: User Manual
User manual Step 3: The “Internet Protocol TCP/IP Properties” window will pop up. Select Use the following IP address and type the IP address, Subnet mask and default gateway. Then select Use the following DNS service address and type the DNS server address. -
Page 11: Rfc 1483 Bridge Dial-Up
User manual 3.2 RFC 1483 Bridge dial-up For Windows 95/98/Me, you need to install third party dial up software that can be obtained from ISP. You can dial up with RFC1483 Bridge protocol support as follow: Step 1: Check your hardware connection followed Chapter 2 Then power on the modem and wait for the ADSL connection established by the LINK LED is solid on Step 2:... - Page 12 User manual Select Connect to the Internet, and then click Next. In “New Connection Wizard” window, please select Set up my connection manually, and then click Next.
- Page 13 User manual Select Connect using a broadband connection that requires a user name and password, then click Next. Enter the name of your ISP, and then click Next.
- Page 14 User manual Enter user name and password, and then click Next. The following window will be shown. Select Add a shortcut to this...
- Page 15 User manual connection to my desktop, then click Finish. A shortcut of dial-up connection will be created on the desktop. Double click the icon of dial-up connection, and a message window will pop up. You can click Connect, just wait for a few seconds; you are ready to visit the Internet.
-
Page 16: Chapter 4 Questions & Answers
User manual Chapter 4 Questions & Answers Question: Why are all led indicators off? Answer: Check the connection between the power adaptor and the power socket, and then check the power switch is on or not. Question: Why doesn’t the LAN led light? Answer: Check the connection between the ADSL modem and your computer, Hub or Switch.