Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ovislink OV303R2M
Summary of Contents for Ovislink OV303R2M
- Page 1 ADSL2+ MODEM User manual...
-
Page 2: Table Of Contents
Contents Chapter 1 Introduction ..................1 Features....................... 1 ADSL standard supports ..................1 Encapsulation supports ..................1 System requirements................... 2 LED status description..................3 Rear panel layout ....................3 Hardware Installation ..............5 Chapter 2 Modem Parameters Setting ............6 Chapter 3 Configuring computer network card IP address .......... -
Page 3: Chapter 1 Introduction
Chapter 1 Introduction The device is a well-designed high-speed ADSL2+ modem/router Features • Full speed, Auto-sense a ADSL routing, bridging • Up to 24Mbps downstream and up to 1Mbps upstream data rate • Friendly GUI for web configuration • Support TR-069 •... -
Page 4: System Requirements
• Classical IP over ATM (RFC 1577) • PPP over ATM (RFC 2364) • PPP over Ethernet (RFC 2516) System requirements Recommended system requirements are: • Pentium 300MHZ or above • Memory: 128MB or above • 10M Base-T Ethernet or above •... -
Page 5: Led Status Description
LED status description Indicator Status Description No power Power Power supplied Quick Blink DSL line is training ADSL DSL line is connected Data Blink DSL data transferring Ethernet connection is OK Blink Ethernet data transferring Rear panel layout Interface Description Switch Power on/off switch Power... - Page 6 Press and hold around 5~10s to reset the hardware. The modem will auto restart. This action will recover the modem’s default configuration. LAN interface for connecting to computer or Switch ADSL connector for connecting to ADSL LINE telephone line...
-
Page 7: Chapter 2 Hardware Installation
Chapter 2 Hardware Installation Please connect the device to you computer as follow: • If connecting to the splitter, connect the “Line” splitter to wall jack using one telephone cable • Use the other telephone cable to connect “MODEM” port of the splitter and “LINE”... -
Page 8: Chapter 3 Modem Parameters Setting
Chapter 3 Modem Parameters Setting Configuring computer network card IP address Configure your network card’s TCP/IP properties to Obtain an IP address automatically from modem, or set the computer’s IP with the same network mask of the modem.(For example: modem’s IP is 192.168.1.1/255.255.255.0, Then you can set computer’s IP to: 192.168.1.x/255.255.255.0. -
Page 9: Ethernet Over Atm (Rfc1483 Bridge) Setting
Here provide the most common RFC1483 Bridge and PPP over Ethernet (RFC2516) setting for reference. If you want to know more about other protocol, please contact your ADSL service provider for details. Ethernet over ATM (RFC1483 Bridge) setting From the Home page, click “Advanced Setup”, see the following:... - Page 10 Click Edit. Set VPI/VCI, see the following: Click the “Next” button, and you can set the encapsulation which get from your ADSL service provider. Select Bridging, see the following:...
- Page 11 Click the “Next” button , select the check box below to enable this WAN service, see the following: Click the “Next” button, make sure that the settings below match the settings provided by your ISP., see the following: Click the “Save/Reboot” button, save your configurations. NOTICE: If you select Dial-UP link, after configuring your ADSL modem, please install the third-party dial up program to access Internet (For example: Ethernet...
-
Page 12: Ppp Over Ethernet (Rfc2516) Setting
PPP over Ethernet (RFC2516) setting PPPoE is also named as RFC 2516. It is a method of encapsulating PPP packets over Ethernet. PPP or Point-to-Point protocol is a method of establishing a network connection/session between network hosts. It usually provides a mechanism of authenticating users. - Page 13 Click the “Next” button. Select PPP over Ethernet (PPPoE) and the type of network protocol and encapsulation mode over the ATM PVC that your ISP has instructed you to use, see the following: Click the “Next” button, fill out PPP Username and PPP Password, see the following:...
- Page 14 Click the “Next” button, uncheck IGMP Multicast, and enable WAN Service, see the following: 6. Click the “Next” button; make sure that the settings below match the settings provided by your ISP. See the following: Click the “Save/Reboot” button, save your configurations, then finish the Setting for PPPoE.
-
Page 15: Tr-069 Configuration
TR-069 Configuration Click the “Management” and then click the “TR-069 Client” to configure the MODEM for TR069: Disable: modem cannot automatically send out the request to the TR069 server Enable: modem can automatically send out the request to the TR069 server Select “Enable”, all items below are effective Inform Interval: Each modem how many seconds sends out the connection request to the TR069 server... -
Page 16: Chapter 4 Questions & Answers
Chapter 4 Questions & Answers Question: Why all LED indicators are off? Answer: • Check the connection between the power adaptor and the power socket • Check the power switch is on or not Question: Why Ethernet LED is not lighting? Answer: •... - Page 17 Question: Why cannot open the Modem configure web page? Answer: Follow below steps to check the communication between the computer and Modem: Click start -> run (input ping demands)-> Ping 192.168.1.1 (Modem IP address). If cannot reach the modem, please check following configuration: •...