OV915WVA is the solution that can provide gigabit speeds by using both copper and fiber The OV915WVA is easy to install and use. The Router connects to an Ethernet LAN or computers via standard Ethernet ports. The xDSL connection is made using ordinary telephone line with standard connectors.
System statistics and monitoring DSL router is targeted at the following platforms: DSL modems, wireless access points and bridge. 2.3 Standards Compatibility and Compliance Support application level gateway (ALG) Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Device is powered off. Internet is synchronized successfully in the route mode. Green Internet Blink Internet data is being transmitted. Ethernet interface is disconnected. Authentication has failed. Green The Ethernet interface is connected. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 10
Green Blink Data is being transmitted. No signal is detected. The Fiber interface is connected. Data is being transmitted through the Fiber Fiber Green Blink interface. The Fiber interface is disconnected. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
RJ-45 port, for connecting the router to a PC or another network LAN 1~4 device. Press the button for at least 1 second and then release it. System Reset restores the factory default settings. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Many environmental factors may affect the effective wireless function of the DSL Router. If this is the first time that you set up a wireless network device, read the following information: Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
If you use 3G WAN service, connect the 3G USB data card to the USB port of the router.The followig figure displays the connection of the DSL router, PC, Figure 4 Connecting the DSL router Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
The configuration principle is identical but should be carried out differently on each operating system. The following displays the TCP/IP Properties dialog box on Windows XP. Figure 5 IP and DNS configuration Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
DSL router for the first time. Click OK to log in to the Web page. Otherwise, please click Cancel to exit the login page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 16
OV915WVA User Manual Figure 6 Login page After logging in to the DSL router as a super user, you can query, configure, and modify all the settings, and diagnose the system. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
GUI. 5.1 Device Information Choose Device Info, and the submenus of Device Info are shown as below: Summary 5.1.1 Choose Device Info > Summary, and the following page appears. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
This page displays the device information such as the board ID, software version, and the information of your WAN connection such as the upstream rate and the LAN address. 5.1.2 Choose Device Info > WAN and the following page appears. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Ethernet and wireless interfaces. Click Reset Statistics to restore the values to zero and recount them. WAN Service 5.1.5 Choose Device Info > Statistics > WAN Service and the following page appears. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Click the Reset button to restore the values to zero and recount them. xDSL 5.1.7 Choose Device Info > Statistics > xDSL and the following page appears. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 21
OV915WVA User Manual Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 22
The Tested Time (sec) can be 1, 5, 10, 20, 60, 120, 180, 240, 300, or 360. Select a time in the drop-down list and click Start. The following pages appear. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
When the ADSL BER test completes, the following page appears. Note: If the BER reaches e-5, you cannot access the Internet. Route 5.1.8 Choose Device Info > Route and the following page appears. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
In this page, you can view the host name, the IP address assigned by the DHCP server, the MAC address this is corresponding to the IP address, and the DHCP lease time. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
OV915WVA User Manual 5.2 Advanced Setup Choose Advanced Setup and the submenus of Advanced Setup are shown as below: Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Click Add to add ATM Interface and the following page appears. In this page, you can enter this PVC (VPI and VCI) value, and select DSL link type (EoA is for PPPoE, IPoE, and Bridge.), encapsulation mode, service category. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 27
Choose Advanced Setup > Layer2 Interface > PTM Interface . In this page, you can add or remove to configure DSL PTM Interfaces. Click Add to add PTM Interface and the following page appears. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 28
In this page, you can configuration the PTM interface Click Apply/Save. Click Apply/Save to save the configuration, and return the following page: If you want to remove this Interface, please select the Remove check box and click Remove. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
In this page, you can select a ETH port. Click Apply/Save to save configuration. Note: If ETH Interface is selected, there are two WAN service types (PPPoE and IPoE). WAN Service 5.2.2 Choose Advanced Setup > WAN Service, and the following page appears. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 30
WAN service.) Step2 In this page, you can select a ATM Interface for the WAN service. After selecting the ATM interface, click Next to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 31
OV915WVA User Manual Step3 In this page, select the WAN service type to be PPP over Ethernet (PPPoE). Click Next to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 32
IP address and port are mapped to the same external IP address and port. Furthermore, any external host can send a packet to the internal host, by sending a packet to the mapped external address. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 33
Bridge PPPoE Frames Between WAN and Local Ports:Enable or disable this function. Enable IGMP Multicast Proxy:If you want PPPoE mode to support IPTV, enable it. Step5 After setting the parameters, click Next to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 34
Next to display the following page. Step7 In this page, you can obtain the DNS server addresses from the selected WAN interface. Click Next, and the following page appears. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 35
(At first, you must add a ATM interface for this WAN service.) Step2 Select an ATM Interface, and then click Next to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 36
Step3 In this page, select the WAN service type to be IP over Ethernet, enter the service description for this service. After finishing setting, click Next to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 37
If selecting Obtain an IP address automatically, DHCP will be enabled for PVC in MER mode. If selecting Use the following Static IP address, please enter the WAN IP address, subnet mask and gateway IP address. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 38
After finishing setting, click Next and the following page appears. Step6 In this page, select a preferred WAN interface as the system default gateway and then click Next to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 39
OV915WVA User Manual Step7 In this page, you can obtain the DNS server addresses from the selected WAN interface. After finishing setting, click Next to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 40
Select the DSL link type to be PPPoA, and select the encapsulation mode to be VC/MUX (according to the uplink equipment). After finishing setting, click the Apply/Save button to apply the setings. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 41
Select the proper interface for the WAN service, and then click Next to display the following page. Step5 In this page, you may modify the service description. Click Next to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 42
PPP IP extension: If you want to configure DMZ Host, you should enable it first. Use Static IPv4 Address: If this function is disabled, the modem obtains an IP address assigned by an uplink equipment such as BAS, through PPPoA Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 43
After finishing setting, click Next to display the following page. Step7 In this page, select a preferred WAN interface as the system default gateway and then click Next to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 44
OV915WVA User Manual Step8 In this page, you can obtain the DNS server addresses from the selected WAN interface. After finishing setting, click Next to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 45
DSL ATM Interface Configuration page. In this page, you need to add a PVC for IPoA mode. Click the Add button in the DSL ATM Interface Configuration page to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 46
Apply/Save button to save the settings. Step3 Choose WAN Service and click Add to display the following page. Step4 Select the proper interface for the WAN service ,and then click Next to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 47
DNS server provided by your ISP and then click Next to display the following page. In this page, Network Address Translation (NAT) allows you to share one Wide Area Network (WAN) IP address for multiple computers on your Local Area Network (LAN). Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 48
After finishing setting, click Next to display the following page. Step8 In this page, select a preferred WAN interface as the system default gateway and then click Next to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 49
In the Wide Area Network (WAN) Service Setup page, click the Add button to display the following page. (At first, you must add a proper ATM interface for this WAN service.) Click the Add button to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 50
OV915WVA User Manual Step2 Select the proper ATM Interface and then click Next to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 51
OV915WVA User Manual Step3 In this page, you can select the WAN service type, and modify the service description for this service. After finishing setting, click Next to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Pin Manage: Click it to configure the 3G PIN. Upload Driver: For a un-support USB dongle, click it to upload the new driver for supporting the USB. The driver is a text file. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 53
User Name: Username provided by your 3G/4G ISP. Password: Password provided by your 3G/4G ISP. Authentication Method: Select a proper authentication method in the drop- down list. You can select Auto, PAP, CHAP, or MSCHAP. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 54
After clicking the Apply/Save button, the following page appears. If the 3G/4G network card is installed, you may click the button on the Action column to establish or disconnect the 3G/4G connection. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
3G/4G connection will be disconnected. If the DSL WAN connection has established, you may manually to perform 3G/4G dial-up, and then the DSL WAN connection will be disconnected. LAN Configuration 5.2.4 Choose Advanced Setup > LAN, and the following page appears. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 56
In this page, you can configure an IP address for the DSL router, enable IGMP snooping, enable or disable the DHCP server, edit the DHCP option, configure the DHCP advanced setup and set the binding between a MAC address and an IP address. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 57
Enabling the LAN Side Firewall Firewall can prevent unexpected traffic on the Internet from your host in the LAN. In this page, you can enable or disable the LAN side firewall. Configuring the DHCP Server Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 58
Configuring the Second IP Address and Subnet Mask for a LAN Interface In the Local Area Network (LAN) Setup page, you are allowed to set the second IP address and the subnet mask for a LAN interface. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 59
DHCPv6 server, enable RADVD and enable the MLD snooping function. Enable DHCPv6 Server: WIDE-DHCPv6 is an open-source implementation of dynamic host configuration protocol for IPv6 (DHCPv6) originally developed by the KAME project. The implementation mainly complies with Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
In this page, you are allowed to add or remove a virtual server entry. To add a virtual server, do as follows: Step 1 Click the Add button to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 61
External Port End: When selecting a service, the port number will automatically be displayed. You can modify it if necessary. Protocol: You may select TCP/UDP, TCP, or UDP in the drop-down list. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 62
Choose Advanced Settings > NAT > Port Triggering, and the following page appears. In this page, you may add or remove an entry of port triggering. Click the Add button to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 63
Open Port End: The end port number that is opened to WAN. Open Protocol: Select the proper protocol that is opened to WAN. You may select TCP/UDP, TCP, or UDP. After finishing setting, click Save/Apply to apply the settings. Note: Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
If you want to clear the DMZ function of the host, please delete the IP address of the host in the field of DMZ Host IP Address, and then click the Apply/Save button. Security 5.2.6 Firewall Choose Security > Firewall and the following page appears. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 65
In some cases, you may want to manage Layer2 MAC address to block or permit a computer within the home network. When you enable MAC filter rules, the DSL router serves as a firewall that works at layer 2. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 66
In this page, you can add or remove the MAC filtering rule. You may change the MAC filtering policy from FORWARDED to BLOCKED by clicking the Change Policy button. Click the Add button to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
After finishing setting, click Apply/Save to save and apply the filtering rule. Parental Control 5.2.7 Time Restriction Choose Advanced Setup > Parental Control > Time Restriction, and the following page appears. Click the Add button to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 68
If you select the select the Include URL list type, you are allowed to access the the URLs in the list. Click the Add button to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
URL address http://www.google.com and the port number 80, and then click the Apply/Save button. See the following figure: Quality of Service 5.2.8 Enabling QoS Choose Advance Setup > Quality of Service and the following page appears. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 70
If the Enable Qos checkbox is not selected, all QoS will be disabled for all interfaces. The default DSCP mark is used to mark all egress packets that do not match any classification rules. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 71
In this page, you can enable, add or remove a QoS rule. Note: The lower integer value for precedence indicates the higher priority. Click the Add button to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 72
Choose Advanced Setup > Quality of Service > Qos Classification and the following page appears. In this page, you can enable, add or remove a QoS classification rule. Click the Add button to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
OV915WVA User Manual Routing 5.2.9 Default Gateway Choose Advanced Setup > Routing > Default Gateway, and the following page appears. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 74
Choose Advanced Setup > Routing > Static Route and the following page appears. In this page, you can add or remove a static routing rule. Click the Add button to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 75
Choose Advanced Setup > Routing > Policy Routing and the following page appears. In this page, you can add or remove a static policy rule. Click the Add button to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 76
In this page, if you want to configure an individual interface, select the desired RIP version and operation, and then select the Enabled checkbox for the interface. After finishing setting, click Apply/Save to save and apply the settings. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
DNS server addresses, or obtain the DNS address from a WAN interface. After finishing setting, click Apply/Save to save and apply the settings. Dynamic DNS Choose Advanced Setup > DNS > Dynamic DNS and the following page appears. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 78
Username: Enter the username for accessing the DDNS management interface. Password: Enter the password for accessing the DDNS management interface. After finishing setting, click Apply/Save to save and apply the settings. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
In this page, you can set the DSL settings. Usually, you do not need to modify the factory default settings. After finishing setting, click Apply/Save to save and apply the settings. UPnP 5.2.12 Choose Advanced Setup > UPnP and the following page appears. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
LAN network, and then click Apply/Save to save and apply the settings. Print Server 5.2.14 Choose Advanced Setup > Printer Server and the following page appears. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
This page is used to display the information of the storage device that connects to the DSL router. Interface Grouping 5.2.16 Choose Advanced Setup > Interface Grouping and the following page appears. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 82
The Remove button will remove the grouping and add the ungrouped interfaces to the default group. Only the default group has IP interface. Click the Add button to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
After finishing setting, click Apply/Save to save and apply the settings. IP Tunnel 5.2.17 5.2.17.1 IPv6 in IPv4 Choose Advanced Setup > IP Tunnel > IPv6inIPv4 and the following page appears. The default value is IPv6 in IPv4 information. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 84
Choose Advanced Setup > IP Tunnel > IPv4inIPv6 and the following page appears. Click Add and the following page appears. In this page, you can add a new tunnel of IPv4 in IPv6. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Choose Advanced Setup > IPSec and the following page appears. In this page, you can add or remove the IPSec tunnel connections. Click the Add button to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 86
If you need to configure the advanced settings of this IPSec tunnel connection, please click the Show Advanced Settings button to display the other parameters. After finishing setting, click Apply/Save to save and apply the settings. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
(or FQDN) used for DNS lookups of your server (for example, www.mydomain.com). Browsers use this information to identify your Web site. Some browsers will refuse to establish a secure connection with your Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 88
The certificate request needs to be submitted to a certificate authority, which will sign the request. Then the signed certificate needs to be loaded to the DSL router. Click Load Signed Certificate in this page, and the following page appears. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 89
In this page, paste the signed certificate, and then click the Apply button. A new certificate is created. Importing an Existing Local Certificate To import an existing certificate, click the Import Certificate button to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 90
In this page, paste the certificate and the private key. Finally, click the Apply button to import the certificate. Trusted CA Choose Advanced Setup > Certificate > Trusted CA and the following page appears. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 91
Click the Import Certificate button to display the following page. In this page, enter the certificate name and paste the certificate content. Finally, click the Apply button to import the certificate. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Use the control buttons to select the desired option. After proper configurations, click Apply to take the configurations effect. Multicast 5.2.21 Choose Advanced Setup > Multicast and the following page appears. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
In this page, you can configure the multicast parameters. After finishing setting, click Apply/Save to save and apply the settings. 5.3 Wireless Choose Wireless and the submenus of Wireless are shown as below: Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Choose Wireless > Basic to display the following page. In this page, the figure in the right area is 2-dimensional code. It includes the wireless SSID and password. You can obtain the wireless SSID and password through scanning this figure. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 95
Enable Wireless Multicast Forwarding (WMF): After enabling this option, the transmission quality of video service such as IPTV can be improved. SSID: For the security reason, you should change the default SSID to a unique name. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
In the current software version, three virtual access points can be configured. After finishing setting, click Apply/Save to save the basic wireless settings and make the settings take effect. Security 5.3.2 Choose Wireless > Security to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 97
This page allows you to configure the security features of the wireless LAN interface. In this page, you can configure the network security settings by the Wi-Fi Protected Setup (WPS) method or setting the network authentication mode. WPS Setup Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 98
You can press the WPS button directly to enable the WPS function. Manual Setup AP This page provides 9 types of network authentication modes, including Open, Shared, 802.1X, WPA, WPA-PSK, WPA2, WPA2-PSK, Mixed WPA2/WPA, and Mixed WPA2/WPA-PSK. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 99
Encryption Strength: You can set 64-bit or 128-bit key. Current Network Key: The current key that you use. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 100
13 ASCII characters or 26 hexadecimal digits. For the 64-bit key, you need to enter 5 ASCII characters or 10 hexadecimal digits. - Shared Mode The parameters’ description of shared mode, please refer to the Open Mode. - 802.1x Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 101
WPA Group Rekey Interval: Setting the interval for renewing key. RADIUS Server IP Address: Enter the IP address of the RADIUS server. RADIUS server is used to authenticate the hosts on the wireless network. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 102
The default key is 87654321. WPA Group Rekey Interval: Setting the interval for renewing key. WPA/WAPI Encryption: You may select AES, or TKIP+AES. - WPA2 Mode Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 103
1812. You may change it according to the server setting. RADIUS Key: Set the RADIUS key for accessing the RADIUS server. WPA/WAPI Encryption: You may select AES, or TKIP+AES. - WPA2-PSK Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 104
The parameters’ description of WPA2-PSK mode, please refer to the WPA-PSK mode. - Mixed WPA2/WPA The parameters’ description of Mixed WPA2/WPA mode, please refer to the WPA2 mode. - Mixed WPA2/WPA-PSK Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
This page is used to allow or reject the wireless clients to access the wireless network of the wireless router. In this page, you can add or remove the MAC filters. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Apply/Save button to add the MAC address to the MAC address list. Wireless Bridge 5.3.4 Choose Wireless > Wireless Bridge to display the following page. This page allows you to configure the wireless bridge features of the wireless LAN interface. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Choose Wireless > Advanced to display the following page. This page allows you to configure the advanced features of the wireless LAN interface. Usually, you do not need to change the settings in this page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 108
Auto-Fallback feature. Auto-Fallback will negotiate the best possible connection speed between the Router and a wireless client. The default value is Auto. Basic Rate: Select the basic transmission rate ability for the AP. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 109
WMM APSD: APSD is short for automatic power save delivery, Selecting enable will make it has very low power consumption. WMM Power Save is an improvement to the 802.11e amendment adding advanced power management functionality to WMM. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
You may diagnose the connection by clicking the Test button or click the Test With OAM F4 button. If the test continues to fail, click Help and follow the troubleshooting procedures. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
OV915WVA User Manual 5.5 Management Choose Management and the submenus of Management are shown as below: Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Choose Management > Settings > Backup to display the following page. In this page, click the Backup Settings button to save your router’s settings to your local PC. Update Choose Management > Settings > Update, and the following page appears. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
In this page, you are allowed to configure the system log and view the security log. Configuring the System Log Click the Configure System Log button to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 114
If you want to log all the events, you need to select the Debugging log level. View System Log Click the View System Log button to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Choose Management > Security Log to display the following page. In this page, you are allowed to configure the system log and view the security log. View Click the view button to view the Security Log. Reset Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
After finishing setting, click the Apply/Save button to save and apply the settings. Internet Time 5.5.5 Choose Management > Internet Time to display the following page. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 117
OV915WVA User Manual In this page, you may configure the router to synchronize its time with the Internet time servers. After enabling Automatically synchronize with Internet time servers, the following page appears. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
In this page, set the proper time servers, and then click the Apply/Save button to save and apply the settings. Access Control 5.5.6 Passwords Choose Management > Access Control > Passwords, and the following page appears. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 119
In the page, you can modify the username and password of different users. After finishing setting, click the Apply/Save button to save and apply the settings. Services Choose Management > Access Control > Services Control and the following page appears. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
In this page, you can enable or disable the different types of services. After finishing setting, click the Apply/Save button to save and apply the settings. Update Software 5.5.7 Choose Management > Update Software, and the following page appears. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 121
Please make sure that the new software for updating is correct, and do not use other software to update the router. Reboot 5.5.8 Choose Management > Reboot and the following page appears. In this page, click the Reboot button, and then the router reboots. Copyright @ 2016 OvisLink (Canada) INC All rights reserved...
Page 122
1 second, and then release it. The default IP address and the subnet mask of the DSL router are 192.168.1.1 and 255.255.255.0, respectively. User/password of super user: admin/admin User/password of common user: user/user Copyright @ 2016 OvisLink (Canada) INC All rights reserved...