Advertisement
Advertisement
To replace your water filter:
ice maker.pushing on the end/face of the filter.alignment guide, slide it gently into the filter housing until it stops against the snap-in connector at the back of the housing.snaps into place (you should hear a click as the cartridge engages the snap-in connector).spurts and sputters that occur as the system purges air out of the dispenser system are normal.four minutes.Water Filter button on the Ice & Water Dispenser control panel for three seconds. When the display changes from "Red" to "Green," the status has been reset.If your refrigerator is not cooling, consider the following:
On/Off button on the temperature control panel (Electronic controls) was pressed and held for three seconds, or if the Freezer and Fresh Food controls (Mechanical controls) were turned to "0".freezer control being set to "OFF" or "0", the refrigerator being in a defrost cycle, the plug at the electrical outlet being disconnected, a house fuse being blown or circuit breaker tripped, or a power outage.If your refrigerator is not producing ice, consider the following:
ice maker.household water supply and ensure the water valve is open.supply line does not kink when the refrigerator is pushed into place.water filter, ensuring it is pushed firmly so it locks solidly into position.water dispenses slowly or not at all, or if the filter is six months old or older, it should be replaced.signal arm from being in the on or down position.Remove the ice container, thaw, and empty the contents. Clean the container and replace it. Alternatively, remove ice cubes that are jamming the dispenser.To reset or turn on the ice maker:
Ice Off button for three seconds until the indicator light is off.wire signal arm to the ON position. Alternatively, press the switch to the I position (rear mounted).To stop your refrigerator from beeping, you typically need to address the cause of the alarm and then press the set key to reset any system alarms. Common reasons for beeping and their solutions include:
power fail alert will be illuminated. Press alarm reset to acknowledge.26°F or greater, an alarm will sound. You can disable it by pressing the set key.55°F or greater, an alarm will sound. You can disable it by pressing the set key.five minutes or more, an alarm will sound. Press the set key to reset.jammed ice cube, an alarm will sound for two minutes. It will reset after two minutes or when the ice cube is removed and the set key is pressed.If your refrigerator is not dispensing water, consider the following:
control lock for three seconds.water filter, ensuring it is pushed firmly so it locks solidly into position.Replace the filter cartridge and push the filter firmly so it locks solidly into position.household water line valve.To change your PureSource Ultra™ air filter:
air filter housing straight out.It is recommended to change the air filter every six months to ensure optimal filtering of refrigerator odors.
If your refrigerator is not dispensing cold water, consider the following:
warmer tap water goes through the filter and enters the water supply system, the chilled water is pushed through to the dispenser. It will take several hours for freshly replaced water to cool down. You can add ice to the cup or container before dispensing water.control lock for three seconds.Replace the filter cartridge and push the filter firmly so it locks solidly into position.household water line valve.To make your refrigerator colder, adjust the temperature settings:
Plus (+) and Minus (-) indicators on the right side of the control panel.+ or - indicator to adjust the temperature to the desired colder setting. The refrigerator temperature can be set from +33°F / +1°C to +47°F / +8°C, and the freezer temperature from -6°F / -21°C to +6°F / -15°C.To set the temperature on your refrigerator:
Plus (+) and Minus (-) indicators on the right side of the control panel.+ or - indicator to adjust the temperature to the desired setting. The refrigerator temperature can be set from +33°F / +1°C to +47°F / +8°C, and the freezer temperature from -6°F / -21°C to +6°F / -15°C.If your interior light is not working, consider the following:
power outage, a house fuse is blown, or a circuit breaker is tripped.in series, so if one is bad or unplugged, several lights may not light up.light bulb may need replacing. Unplug the refrigerator's power cord, wear gloves, remove the light cover, unscrew and replace the old bulb with an appliance bulb of the same type and wattage (normally 40 watts), replace the cover, and plug in the refrigerator.To make the freezer colder, adjust the temperature setting:
Plus (+) and Minus (-) indicators on the right side of the control panel.+ or - indicator to adjust the temperature to the desired colder setting. The freezer temperature can be set from -6°F / -21°C to +6°F / -15°C.After adjusting the setting, allow 24 hours for the temperature to stabilize.
To remove the doors from your refrigerator:
To prepare for removing the doors:
electrical power cord from the wall outlet.toe grille.door shelves.To remove the refrigerator top hinge cover:
three screws from each cover over the top door hinges.hinge cover straight up and off.To remove the refrigerator door:
door's top hinge with a pencil to aid reinstallation.two screws from the top hinge. Lift the door off the bottom hinge and set it aside.To remove the freezer top hinge cover:
two screws from each cover over the top door hinges.hinge cover straight up and off.To remove the freezer door:
multi-wire cable connector located above the top hinge by grasping both sides and pulling apart.hinge with a pencil.water tube from the connector below the freezer door by pressing its outer sleeve inward.screws from the top hinge and pull the multi-wire cable through it. Lift the door off the bottom hinge.two bottom hinge screws and hinge if necessary.water tube extending from the bottom hinge.To remove the light bulb cover:
For LED Lights (select models):
power cord.lens cover.For traditional light bulbs (select models):
power cord.gloves as protection.light cover, if necessary.To level your refrigerator:
To level the cabinet using the front rollers:
toe grille.flat-blade screwdriver or 3/8 inch socket wrench to raise or lower the front rollers.bind-free with their seals touching the cabinet on all four sides.To level the doors using the adjustable lower hinge (some models):
set screw that locks door height into position.adjustment screw clockwise using a 7/16 inch wrench.adjustment screw clockwise using a 7/16 inch wrench.door stop contacts the lower hinge and the top of the door does not contact the upper hinge through full movement.set screw, locking the door height.toe grille.To improve the energy efficiency of your refrigerator:
out of direct sunlight and away from heat sources like the range or dishwasher.too frequently or for too long, as warm air entering the refrigerator causes it to run more.Clean the condenser regularly. The toe grille should be removed, and both sides of the condenser should be vacuumed.To remove a cantilever shelf:
front edge of the shelf up.shelf out.To replace the shelf, insert the hooks at the rear of the shelf into the wall bracket, then lower the shelf into the desired slots and lock it into position.
Need help?
Do you have a question about the FGHS2355PF5A and is the answer not in the manual?
Questions and answers
When dispensing water a loud noise is coming from the bottom of the refrigerator
A loud noise from the bottom of the Frigidaire FGHS2355PF5A refrigerator when dispensing water could be due to the condenser fan or the compressor. The condenser fan, located at the bottom, may produce noise if it is dirty or obstructed. The compressor, which cycles on and off, can also create clicking or humming sounds during operation. Cleaning the condenser fan or checking for obstructions may help reduce the noise.
This answer is automatically generated
@Mr. Anderson the water in not dispensing just noise
@Mr. Anderson sounds like the pump wants to go but not getting water
Water accumulates and freezes on floor of freezer under drawer! Eventually out door and onto floor.
Water can accumulate and freeze on the floor of the freezer in a Frigidaire FGHS2355PF5A if the ice dispenser is not used frequently. This causes ice cubes to freeze together in the bin, jamming the dispenser mechanism. If the freezer door does not close properly—such as when the ice bin is not aligned correctly—warm air can leak into the freezer, leading to melting and refreezing of ice, which causes water to accumulate and freeze on the floor.
This answer is automatically generated
The Interface Panel LED lights are not working well. Some of the numbers still have bright parts, but the rest are dimming. Can I replace a fuse or something to light them back up?
Yes, the LED lights on the Frigidaire FGHS2355PF5A can be replaced. The process involves removing the lens cover, replacing the LED light board (Part #242196201), and ensuring the light faces inward toward the LED light unit.
This answer is automatically generated
where is the thermistor located in a frigidaire gallery fghs2631pf4a
Where do I go to purchase a fixed door bin