Sanyo DVD-SL33 Instruction Manual page 15

Setting digital out
If the operation DIGITAL OUT socket is connected to the amplifier, you
must set as follows.
1. Press the SETUP button in the stop mode. The setup screen
appears.
Language Display
2. Press the a button to select "Digital Out", then press the ENT button.
"Digital Out" screen appears.
Language Display
96kHz LPCM 48 kHz LPCM
Dolby Digital
DTS
MPEG
3. Press the 5 or 4 button to select the item (highlighted), then press
the ENT button. The submenu appears.
Example: To set "Dolby Digital"
96kHz LPCM 48 kHz LPCM
Dolby Digital LPCM
DTS
MPEG LPCM
4. Press the 5 or 4 button to select the submenu (highlighted), then
press the ENT button. The submenu appears.
Example: To select "Dolby Digital BitStream".
96kHz LPCM 48 kHz LPCM
Dolby Digital LPCM
DTS
MPEG LPCM
5. Press the ENT button. (In this example, "Dolby Digital BitStream"
remains.)
6. Repeat steps 3 ~ 5 for other items.
7. Press 4 to skip back to the setup screen (or press the SETUP
button).
96kHz LPCM (96kHz Liner Pulse Code Modulation):
If your amplifier is available for 96kHz sampling, select "96kHz LPCM".
If not, select "48kHz LPCM".
Notes:
- When "48kHz LPCM" is set, there are 48kHz LPCM audio signals
from the AUDIO OUT jacks, not 96kHz LPCM audio signals.
- When playing back the DVD disc which recorded with 96kHz LPCM,
there is no digital output.
- However playing back the DVD disc with no copyright protection,
the sound is original recorded sound.
Dolby Digital:
If your amplifier has Dolby Digital Decoder, select "BitStream". If not,
select "LPCM".
DTS:
If your amplifier has DTS Decoder, select "On". If not, select "Off".
MPEG (Moving Picture Expert Group):
If your amplifier has MPEG2 Decoder, select "BitStream". If not, select
"LPCM".
Digital Out Parental
Digital Out Parental
LPCM
Off
LPCM
LPCM
BitStream
Off
LPCM
Off BitStream
Setting Parental
1. Press the SETUP button in the stop mode. The setup screen
appears.
Language Display
2. Press the a button to select "Parental". then press the ENT button.
"Parental" screen appears.
Language Display
Password
Level
3. Press the 5 button to skip "Password: ----" and select "Level".
Password
Level
4. Press the ENT button repeatedly to select the parental lock level
("Level Off" ~ "Level 8").
Example: To select "Level 1"
Password
Level
5. Press the 4 button to return to "Password ----".
6. Enter a number in 4 digits.
Password
Level
Note:
If you make a mistake, press the CLEAR button.
7. Press the ENT button. The password is now set.
Password
Level
Note:
If you do not set it, Parental Control does not work, and it returns
to the initial settings.
8. Press the SETUP button.The setup screen disappears.
Parental Control
MPAA (Motion Picture Association of America) Guideline is a rating
system that provides advanced cautionary information to parent about
the content of movie programs.
The parental lock level is equivalent to the following MPAA Rating
System.
Level 7: NC-17 (No one 17 and under admitted)
Level 6: R (Restricted)
Level 4: PG-13 (Parents strongly cautioned)
Level 3: PG (Parental guidance suggested)
Level 1: G (General audiences)
Some DVD discs contain a restriction level which enables parents to
prevent playback of discs by children. This unit is equipped with a pass-
word designed to prevent children changing the level.
You cannot play DVD video discs rated higher than the level you se-
lected unless you cancel the parental lock function.
For example, when you select level "5", the unit will not play discs with
ratings of "6", "7" or "8". The information will appear on the TV screen.
If you forget the password...
Enter "788444" even if 4 digits "----" appears, then press the ENT
button to clear the current password. Enter a new password and set
the parental lock level again.
Note:
DVD discs may or may not respond to the parental lock settings. Make
sure this function works with your DVD discs.
Digital Out Parental
Digital Out Parental
----
Off
----
Off
----
1
1
----
1
14