Advertisement
Available languages
Available languages
|
Range
Installation
Important
Note: Door removal is not a requirement
for
installation
of the range, but is an added convenience.
Refer to the Use
and Care Guide for
oven door removal
instructions.
Figure 6
Standard
installation
|
The range cooktop overlaps the countertop at
the sides and the range rests on the floor. The
cooktop is 31 1/2" (80 cm) wide.
|
Install base cabinets 30" (76,2 cm) apart. Make
sure they are plumb and level before attaching
cooktop. Shave raised countertop edge to clear
31 1/2" (80 cm) wide range top rim.
[_
Install cabinet doors 31" (78,7 cm) min. apart so it
will not interfere with range door opening.
Cutout countertop
exactly as shown on page 4.
For models
equipped
with
Levelinq
Device:
Make sure the front leveling legs and the rear
leveling device are setup higher than the height
of the cabinet.
_
Install the anti-tip
bracket
at
this point before placing
the range at its final
position.
Follow the installation
instructions on
page 12 or 13 or on the anti-tip bracket template
supplied with the range.
To provide an optimum installation, the top
surface of the countertop
must be level and
flat (lie on the same plane) around the 3 sides
that are adjacent to range cooktop. Proper
adjustments
to make the top flat should be made
or gaps between the countertop
and the range
reduce the risk of damaging
your appliance, do not handle or manipulate
it by
the cooktop or control console. Manipulate with
care.
Position range in front of the cabinet opening.
Make sure that the cooktop which overhangs the
countertop
clears the countertop.
If necessary,
raise the unit by lowering the leveling legs.
Slide the range into the cutout opening and
center it before leveling it.
Level the range (see section 9). The floor where
the range is to be installed must be level. Follow
the instructions
under "Leveling the Range-
Models Equipped with Leveling Device".
Adjust leveling legs so that the underside of the
cooktop is sitting on the countertop.
Carefully
screw in (refer to Leveling the range: Models
equipped with Leveling Device") the back leveling
leg until the cooktop overhang touches slightly
the countertop. Then carefully screw in the front
two leveling legs until the cooktop overhang
touches slightly the countertop.
For models
equipped
with
Levelinq
Leq
only (no leveling
device):
[_
Make sure the four leveling legs (front and rear)
are setup higher than the height of the cabinet
|
_
- "
" ' Install the anti-tip
bracket
at
this point before placing
the range at its final
position.
Follow the installation
instructions
on
page 12 or 13 or on the anti-tip bracket template
supplied with the range.
[_
To provide an optimum installation, the top
surface of the countertop
must be level and
flat (lie on the same plane) around the 3 sides
that are adjacent to range cooktop. Proper
adjustments
to make the top flat should be made
or gaps between the countertop
and the range
cur.
_
To reduce the risk of damaging
your appliance, do not handle or manipulate
it by
the cooktop. Manipulate with care.
Position range in front of the cabinet opening.
Make sure that the cooktop which overhangs the
countertop
clears the countertop.
If necessary,
raise the unit by lowering the leveling legs.
|
Level the range (see section 9). The floor where
the range is to be installed must be level. Follow
the instructions
under "Leveling the Range-
Models Equipped with Leveling Legs".
|
Slide the range into the cutout opening.
If Accessories
Needed
Installation
With Backguard
A backguard
kit can be ordered through a Service
Center. The cutout depth (21¾" (55,2 cm) Min., 22%"
(56,2 cm) Max.) needs to be increased to 24" (61
cm) when installing a backguard
Installation
With End Panel
An end panel kit can be ordered through a Service
Center.
Installation
With Side Panel
A side panels kit can be ordered through a Service
Center. Install cabinet doors 31" (78,7 cm) min. apart
so as not to interfere with range door opening.
9
Advertisement
