Frigidaire FFGS3025PWA Installation Instructions Manual page 11

_To prevent f lare-ups andavoid
creation of harmful b y-products, donot usethecooktop
withoutallburnercapsproperlyinstalled to insure
properignition andgasflamesize.
Alwayskeepthe burner capsandburnerheadsin
placewhenever t hesurfaceburners arein use.DO
not allowspills, food, cleaningagentsor anyother
materialto enterthe gasorifice holderopenings.
Checkandbesurethesizeof eachburner cap
matches thesizeofthe burnerhead.Checkandbe
surethatall roundstyleburnercapsarecorrectly in
placeon roundburnerheads.
Checkandbesurethatallovalstyleburner capsare
correctly in placeon ovalburner heads(if equipped).
Checkandbesurethatall dualor twinstyleburner
capsarecorrectly in placeondualor twinheads(if
equipped).
Onroundstyleburners, t he burnercaplip (Figure10)
shouldfit snugintothecenterofburnerheadandbe
level.Refertofigures11& 12forcorrectandincorrect
burnercapplacement.
Oncein place, y oumaycheckthefit bygentlysliding
theburner capfromsidetoside(Figure 13)tobesure
it is centered andfirmlyseated. W henthe burner c aplip
makes contact i nsidethecenter o f theburner headyou
willbeabletoheartheburner capclick.Please note
thatthe burner c apshouldNOTmoveoffthecenterof
theburner head whensliding fromsideto side.
BurnerCap
Burner _ _x, Burner
Head
Cap
Lip
Fig. 10
Correct Burner Cap Incorrect Burner Cap
Placement - Fig. 11 _ Placement- Fig. 12
| Check the Igniters
Operation of electric igniters should be checked after
range and supply line connectors have been carefully
checked for leaks and range has been connected to
electric power.
a. To check for proper lighting, push in and turn a surface
burner knob to the LITE position. You will hear the
igniter sparking.
b. The surface burner should ignite when gas is available
to the burner. Purge air from supply lines by leaving
knob in the LITE position until burner ignites. Each
burner should light within four (4) seconds in normal
operation after air has been purged from supply lines.
c. Visually check that burner has a flame, Once the
burner ignites, the control knob should be turned out
of the LITE position.
d. Try each surface control knob separately until all
burner valves have been checked. Each burner
location is equipped with a separate electrode.
Adjust the "LOW" Setting of Surface
Burner Valves
(linear flow)
Test to verify if LOW setting should be adjusted:
a. Push in and turn control to LITE until burner ignites.
b. Push in and quickly, turn knob to lowest position.
c. If burner goes out, reset control to OFF.
d. Remove the surface burner control knob.
For all burner styles (except Dual and Bridge burner)
e. Insert a thin-bladed screwdriver into the hollow valve
stem and engage the slotted screw inside. Flame size
can be increased or decreased with the turn of screw.
Turn counterclockwise to increase flame size. Turn
clockwise to decrease flame size (Figure 14).
Adjust flame until you can quickly turn knob from LITE to
lowest position without extinguishing the flame. Flame
should be as small as possible without extinguishing.
For Dual and Bridge burner style adjustment only:
e. The inner portion (Simmer) of the dual burner flame
size or the rear portion of the bridge burner flame size
can be increase or decrease with the turn of screw A.
Use screw B to adjust flame size of the outer portion
of the Dual Burner or the center portion of the Bridge
Burner (Figure 15). Turn the screw counterclockwise
to increase flame size. Turn clockwise to decrease
flame size. Adjust flame size until you can quickly
turn the knob from LITE to lowest position without
extinguishing the flame. Flame should be as small as
possible without going out.
Note: Air mixture adjustments are not required on
surface burners.
Fig. 13
Turn on Electrical Power and Open
Main Shutoff Gas Valve
11
Hollow
Valve
Stem
Figure 14
Figure 15