Blizzard Lighting™ assumes no responsibility or liability for any errors or omissions that may appear in this user manual. Blizzard Lighting™ reserves the right to update the existing document or to create a new document to correct any errors or omissions at any time.
In the unlikely event your unit may require service, please open a support ticket at www. blizzardlighting.com/tickets. Page 4 Stiletto™ Z19 Beam Moving Head - Rev. B (c) 2014 Blizzard Lighting, LLC...
Figure 2: The Rear Connections DMX 3-pin In DMX 5-pin In Power Switch Power In Power Out DMX 5-pin Out Fuse Cover DMX 3-pin Out Page 6 Stiletto™ Z19 Beam Moving Head - Rev. B (c) 2014 Blizzard Lighting, LLC...
Maximum capacitance between conductors – 30 pF/ft. Maximum capacitance between conductor & shield – 55 pF/ft. Maximum resistance of 20 ohms / 1000 ft. Nominal impedance 100 – 140 ohms Page 7 Stiletto™ Z19 Beam Moving Head - Rev. B (c) 2014 Blizzard Lighting, LLC...
Step 3: Connect other fi xtures in the chain from output to input as above. Place a DMX terminator on the output of the fi nal fi xture to ensure best communication. Page 8 Stiletto™ Z19 Beam Moving Head - Rev. B (c) 2014 Blizzard Lighting, LLC...
• Safety cables MUST ALWAYS be used. • Never mount in places where the fi xture will be exposed to rain, high humidity, extreme temperature changes or restricted ventilation. Page 9 Stiletto™ Z19 Beam Moving Head - Rev. B (c) 2014 Blizzard Lighting, LLC...
Better safe than sorry! Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet. Page 10 Stiletto™ Z19 Beam Moving Head - Rev. B (c) 2014 Blizzard Lighting, LLC...
fi xture with a safety cable. Be sure to only use the designated rigging point found on the underside of the base assembly for the safety cable. Never secure a safety cable to a carrying handle. Page 11 Stiletto™ Z19 Beam Moving Head - Rev. B (c) 2014 Blizzard Lighting, LLC...
To return to the previous option or menu without changing the value, press the <MENU> button. Page 12 Stiletto™ Z19 Beam Moving Head - Rev. B (c) 2014 Blizzard Lighting, LLC...
Sets fi xture in single auto operation mode Auto Alone Auto Sets fi xture as master auto operation to be used Master with slave units Page 13 Stiletto™ Z19 Beam Moving Head - Rev. B (c) 2014 Blizzard Lighting, LLC...
Verify proper mode of operation. Is the fi xture in “Auto” On Its Own mode? If your problem isn’t listed, or if problems persist, please open a support ticket at www.blizzardlighting.com/tickets. Page 17 Stiletto™ Z19 Beam Moving Head - Rev. B (c) 2014 Blizzard Lighting, LLC...
It is fl exible, robust, and scalable, and its ability to control everything from dimmer packs to moving lights to foggers to lasers makes it an indispensable tool for any lighting designer or lighting performer. Page 18 Stiletto™ Z19 Beam Moving Head - Rev. B (c) 2014 Blizzard Lighting, LLC...
Damage incurred in shipping is the responsibility of the shipper, and must be reported to the carrier immediately upon receipt of the items. Claims must be made within seven (7) days of receipt. Page 19 Stiletto™ Z19 Beam Moving Head - Rev. B (c) 2014 Blizzard Lighting, LLC...
Neutrik AG, Neutrik USA, or any related entity. Neutrik® and powerCON® are registered trademarks of Neutrik AG. Page 20 Stiletto™ Z19 Beam Moving Head - Rev. B (c) 2014 Blizzard Lighting, LLC...
Page 21
This page left intentionally blank Page 21 Stiletto™ Z19 Beam Moving Head - Rev. B (c) 2014 Blizzard Lighting, LLC...
Page 22
This page left intentionally blank Page 22 Stiletto™ Z19 Beam Moving Head - Rev. B (c) 2014 Blizzard Lighting, LLC...
Page 23
This page left intentionally blank Page 23 Stiletto™ Z19 Beam Moving Head - Rev. B (c) 2014 Blizzard Lighting, LLC...
Page 24
Enjoy your product! Our sincerest thanks for your purchase! --The team @ Blizzard Lighting...