Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Serpent Spyder SR X2 MID
Summary of Contents for Serpent Spyder SR X2 MID
- Page 1 INSTRUCTION MANUAL & REFERENCE GUIDE...
-
Page 2: Specifications And Leads The Way In
Serpent drivers, which gives you superior technical support and access to many The exploded views and parts lists for the Serpent Spyder are included in the back of benefits that only Serpent drivers can enjoy. this manual. The exploded views show all... - Page 3 Read this first! this car on public roads, crowded places or near infants. - Before operating this car, always check the mechanical status of the car. Also check that the transmitter and - This is a highly technical hobby product, intended to be used receiver frequencies correspond and are not used by in a safe racing environment.
- Page 4 FRONT ASSEMBLY STEP 4x8x3 4x8x3 3x6x0.5 3x6x0.5 Nylock nut M3 Nylock nut M3 M3x12 15.25 mm STEP M3x12 15.25 mm NOTE: Make sure to assemble the ballstud through the conical shim 4x8x3 in the direcction 4.7- 5.2 mm indicated by the red arrow.
- Page 5 STEP M3x12 M3x10 STEP INCLUDED 1.25mm 1.5mm 1.75mm Servo Spacer Manufacturer M3x10 Airtronics 1+3+4 3.2x7x0.5 Futaba Hitec KO Propo Spektrum 1+2+3 Use the following servo horns with this brand of servos: M3x8 23 Sanwa / KO / JR 24 Hitec 25 Futaba / Hitec / Savox NOTE: Make sure to put servo in...
- Page 6 M3x18 STEP M3x10 NOTE STEP Place the caster shims and the bushings in the steering block first. Then slide the assembly onto the casterblock M3x4 M3x12 5x10x4 0.75 5x10x4 0.75 NOTE There are three types of steering arms. Please, assemble number as default M3x12 MORE...
- Page 7 STEP 3x33 STEP M3x14 M3x3 11.1 27.3 mm STEP 11.2 17.25 mm 17.25 mm 12.8 mm 3x6x1 NOTE: 12.8 mm Make sure to assemble the ballstud through the conical shim in the direcction indicated by the red arrow. Page...
- Page 8 12.1 STEP 31.4mm 12.2 NOTE: Make sure to assemble the ballstud through the conical shim in the direcction indicated by the red arrow. 12.8 mm 12.8 mm 3x6x1 15.25 mm 15.25 mm M3x20 STEP M3x20 M3x10 M3x10 Front Shocks position detail view Page...
- Page 9 REAR ASSEMBLY STEP 2x10 LEFT 10x15x4 Rear upright and insert 5x13x4 assembly detail view 5x8x0.3 2x10 M2x6 STEP 3x33 M2.3x4 Front Inserts detail view (use ASSEMBLY CORRECT ORDER: STEP number also in the front block) 1) Introduce the pin in the wishbone 2) Place the rear insert in the rear part of the toe block...
-
Page 10: Step
STEP M3x14 M3x14 M3x12 M3x12 BALL DIFF ASSEMBLY STEP 5x8x2.5 5x8x2.5 STEP STEP NOTE: 8 balls Page... - Page 11 HOW TO ADJUST THE DIFF STEP As default setting screw all the way in, and back out ¼ turn. Make small adjustments depending on the track condition. NOTE: Lubricate o-ring with grease TRANSMISSION ASSEMBLY STEP 22.1 22.2 M3x12 NOTE: The diff screw has to be oriented to the right side of the car.
-
Page 12: Step
STEP Pinion is NOT INCLUDED in the kit. See Serpent pinion list in the ref- guide. INCLUDED M3x8 M2.5x6 3.2x7x0.5 STEP M3x14 M3x14 STEP 27.9 mm Page... - Page 13 17.25 mm STEP 15.25 mm 3x6x1 17.25 mm 15.25 mm NOTE: Make sure to assemble the ballstud through the conical shim in the direcction indicated by the red arrow. STEP M3x25 M3x25 M3x10 M3x14 STEP M3x22 M3x10 M3x14 STEP Page...
- Page 14 SHOCK ABSORBERS ASSEMBLY 31.1 31.2 31.3 STEP Nut M2 Use some silicone oil during assembly Insert the Note orientation o-ring of the shock inside the cartridge REAR SHOCKS FRONT 31.4 31.4 FRONT SHOCKS REAR SHOCKS SHOCKS Use some Use some silicone silicone oil during...
-
Page 15: Ball
31.7 31.8 FRONT SHOCKS Assemble the spring With shockrod fully M2.3x4 and spring-cup (align in, mount the o-ring correctly) to complete and screw. the shock. HIGH REAR SHOCKS STEP NOTE: Do not overtighten and smash bushing with the nut and note orientation of the lower shock pivot ball M3 Plastic Nut Flanged... - Page 16 ELECTRONICS ASSEMBLY Tip: Use double sided NOT INCLUDED STEP tape to mount the ESC and RX to the chassis. M3x16 34.2 34.1 STEP M3x10 NOTE: Only assemble this parts if you are going to use shorty lipos. Default Battery Configuration: SADDLE LIPOS STEP INCLUDED...
- Page 17 Same for the body mounting holes. 3) Remove the body protection film Nut M4 flanged on the outside of the body. 4) Apply the provided Serpent and Spyder decals, and mount the body Page on the bodyposts, with the provided bodyclips.
-
Page 18: Table Of Contents
REF GUIDE: EXPLODED VIEWS and PARTS-LIST Contents FRONT ASSEMBLY I FRONT ASSEMBLY II BALL DIFF ASSEMBLY TRANSMISSION ASSEMBLY REAR ASSEMBLY SHOCKS ASSEMBLY FINAL ASSEMBLY PARTS-LIST Page... -
Page 19: Front Assembly I
FRONT ASSEMBLY I Page... -
Page 20: Front Assembly Ii
FRONT ASSEMBLY II Page... -
Page 21: Ball Diff Assembly
BALL DIFF ASSEMBLY Page... -
Page 22: Transmission Assembly
TRANSMISSION ASSEMBLY Page... -
Page 23: Rear Assembly
REAR ASSEMBLY Page... -
Page 24: Shocks Assembly
SHOCKS ASSEMBLY Page... -
Page 25: Final Assembly
FINAL ASSEMBLY Page... -
Page 26: Parts-List
PARTS-LIST Part no Description 500229 Shock spring green 3.7lbs fr (2) SRX2 500003 Serpent Spyder Buggy SXR-2 MM 2wd 500230 Shock spring orange 2.0lbs rr (2) SRX2 1/10 500231 Shock spring red 2.1lbs rr (2) SRX2 500232 Shock spring pink 2.2lbs rr (2) SRX3... - Page 27 REAR SECTION 500277 Motor plate SRX2 MM 401381 CVD insert (2) 600116 O-ring tank (4) 401387 Wheelhexagon (2) OPTIONALS 500105 1/10 buggy rim rr white (2) 500114 Upright L+R SRX2 411107 Diff balls. 1/8 ceramic (12) 500134 Rear suspension insert (24) SRX2 500192 Geardiff set SRX2 500135...
- Page 28 190515 Ball driver hex wrench 3.0 x 120mm 110145 Screw allen roundhead flanged M3x12 190516 Tool tip allen wrench 1.5 x 120mm (10) 190517 Tool tip allen wrench 2.0 x 120mm 110146 Screw allen roundhead flanged M3x16 190518 Tool tip allen wrench 2.5 x 120mm (10) 190519 Tool tip allen wrench 3.0 x 120mm 110147 Screw ph roundhead M2.5x5 (10) 190520 Tool tip ball driver hex wrench 2.0 x 120mm...
- Page 29 190208 Winter jacket Serpent black- 110303 E-clip 5.0 (10) orange hooded (4XL) 110304 E-clip 7.0 (10) 190156 Polo shirt Serpent black (S) 110305 Seger clip 12x1.0 (10) 190157 Polo shirt Serpent black (M) 110306 E-clip 6.0 (10) 190158 Polo shirt Serpent black (L) 110307 E-clip 9.0 (10)
- Page 30 NEWS / NOTES Page...
- Page 31 NEWS / NOTES Page...
- Page 32 - info@serpent.com...
Need help?
Do you have a question about the Spyder SR X2 MID and is the answer not in the manual?
Questions and answers