Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for C&K systems Sierra S5030
Summary of Contents for C&K systems Sierra S5030
- Page 1 Technical Manuals Online! - http://www.tech-man.com...
-
Page 2: Table Of Contents
Overview Your Security System ........1 How Your Security System Works ....2 Your System's Programming ......3 Getting Used to Your System ......3 Quick Guide to Your Keypad ......4 Understanding the Lights (LEDs ...... 5 Emergency Keys ..........6 User Codes and Privileges About User Codes and User Numbers .... - Page 3 Arming with Not-Ready Zones ....... 23 Bypassing ............24 Quick Bypassing ..........25 Optional Arming Features ......26 Canceling an Arming Sequence ....27 Disarming and Alarms Entry Delays ........... 28 Disarming ............28 Automatic (Timed) Disarming ......29 Canceling an Alarm ........30 After an Alarm ..........
- Page 4 Common System Messages ......47 Troubleshooting Service Conditions ....48 Partitioning What Areas Do ..........51 How Areas Affect User Codes ....... 53 Pre-Assigned User Numbers ......54 Changing Area User Codes ......54 How Areas Affect the System ......55 Notes System Configurations ........
-
Page 5: Your Security System
Your Security System Your security system includes a number of detection devices, such as magnetic contacts, glassbreak detectors, smoke detec- tors, and motion sensors. These devices identify alarm condi- tions and report them to the control panel. If programmed, the control panel sounds an alarm. -
Page 6: How Your Security System Works
How Your Security System Works When an intruder enters the building, a detection device is trig- gered. The device sends a message to the control panel. The device may have LEDs (lights) that flash. The control panel responds by sounding the alarm. (Alarm sounds vary. -
Page 7: Your System's Programming
Your System's Programming Your Sierra security system has been customized to suit your needs. Besides selecting the best equipment for your building, your installer has programmed your system to operate in a way that reflects your lifestyle. For example, your system may be programmed to recognize special user codes, to arm and disarm automatically, or to report to a monitoring station. -
Page 8: Quick Guide To Your Keypad
Quick Guide To Your Keypad The drawing below identifies and explains the important features of your LED keypad. Emergency Keys Keypad Lights (LEDs) To notify your monitoring Describes the system's status, such as: station of an emergency, —if the system is ready to arm press and hold these keys —if an alarm has occurred for two seconds until you... -
Page 9: Understanding The Lights
Understanding the Lights (LEDs) Your keypad has a number of LEDs that summarize the status of your security system. Each LED can convey several different mes- sages by being on, off, or blinking. The illustration shows what messages the lights communicate. LED Blink Rates Slow: light blinks twice every three seconds Fast: light blinks three times every two seconds... -
Page 10: Emergency Keys
Emergency Keys Your keypad is equipped with To Use Emergency Keys: three emergency keys. The keys do not function unless To report a medical emer- your installer activated them. If gency, press and hold the activated, these keys are a key for 2 seconds. -
Page 11: About User Codes And User Numbers
About User Codes and User Numbers You can assign a different user code and user number to each person who operates the system. Your security system supports up to 60 users. If you prefer, you can assign only one user code and user num- ber to a group of users. -
Page 12: How To Assign Or Change User Codes
How to Assign or Change User Codes To Assign or Change User codes can be created or a User Code: changed as often as you like. Any code you select must be Press and hold the four digits long. You cannot use 0000, or assign the same [user prg] key for 2 seconds code to more than one user... - Page 13 When you are changing a user code, the zone LEDs light to iden- tify which two-digit user number you have selected. Match your keypad's LED pattern to the charts below to identify the user num- ber. Lit LED Pattern Lit LED Pattern Technical Manuals Online! - http://www.tech-man.com...
-
Page 14: How To Correct A User Code Entry
How to Correct a User Code Entry You will know that you entered To Correct a User Code Entry: an incorrect code when the system does not complete your Re-enter code. command. As a security fea- ture, your keypad does not beep when you enter an incor- rect user code. -
Page 15: Types Of User Codes
Types of User Codes This section identifies the types of user codes your system may recognize. At the top of each user code section, you will see a checklist like this: Standard Code _X_ Optional Code ___ Active Certain Days/Times ___ Items on this checklist followed by an "X"... -
Page 16: Kidwatch Code
Kidwatch Standard Code ___ Optional Code _X_ Code Active Certain Days/Times _X_ To Change Kidwatch Days : Designed for parents whose children come home first, this option allows you to be notified Press and hold the if your child is not home by a [kidwatch] key for 2 seconds certain time. - Page 17 To Turn Kidwatch On/Off: Changing Kidwatch Days. You have the option of chang- ing which days Kidwatch is in Press and hold the effect. To do so, follow the pro- [kidwatch] key for 2 seconds cedure on the previous page. until you hear two beeps.
-
Page 18: Maid Code
Maid Standard Code ___ Optional Code _X_ Code Active Certain Days/Times _X_ To Change Maid Days: Unlike other user codes, which work any day of the week, the Press and hold the Maid Code works only on certain [maid] key for 2 seconds un- days of the week. -
Page 19: Temporary Maid Code
Temporary Standard Code ___ Optional Code _X_ Maid Code Active Certain Days/Times _X_ To Start the As the preceding section Maid Code Timer: shows, the Maid Code can be programmed to work on certain Press and hold the days of the week only. If you [maid] key for 2 seconds un- prefer, however, you can set the Maid Code to work for the... -
Page 20: Duress Code
Duress Standard Code ___ Optional Code _X_ Code Active Certain Days/Times _X_ Technical Manuals Online! - http://www.tech-man.com... -
Page 21: Selecting The Right User Number
Selecting the Right User Number At installation, each user number is assigned rights and privi- leges. For example, user number 18 may have the right to arm, disarm, and bypass zones. This is true even if, in this example, there is no user 18 using the system. Thus, when you assign a user code to a new user, be sure that you select a user number with the privileges you want that user to have. -
Page 22: How The Arming Modes Differ
How the Arming Modes Differ Your security system can be armed in a number of ways, to suit different situations. These modes are summarized below. Full Arming. You cannot be inside the building when it is armed with full-arming. If sensors detect movement within a building, or at the building's perimeter, an alarm sounds. -
Page 23: Exit Delay
Exit Delay An exit delay is the amount of time you have to exit and secure the building, once your security system begins to arm. These delays last from 20 to 255 seconds, depending upon how your system was programmed. During the exit delay, the Arm LED blinks. -
Page 24: Home Arming
Interior armed ___ Home Perimeter armed _X_ Exit allowed _X_ Arming Requires user code _X_ Automatically arms ___ No entry allowed ___ To Home Arm the System: With home arming, you can re- main inside a building while its Make sure the Ready LED is perimeter sensors (such as doors and windows) are armed. -
Page 25: Instant Home-Arming
Interior armed ___ Instant Perimeter armed _X_ Exit allowed ___ Home-Arming Requires user code _X_ Automatically arms ___ No entry allowed _X_ To Arm the System with With instant home-arming, an Instant Home-Arming: alarm sounds the instant a sen- sor on the building's perimeter Make sure the Ready LED is detects a problem. -
Page 26: Automatic (Timed) Arming
Interior armed _X_ Automatic (Timed) Perimeter armed _X_ Exit allowed _X_ Arming Requires user code ___ Automatically arms _X_ No entry allowed ___ To Change Automatic Your system can automatically Arming Days: arm itself at preset times of the day. Press and hold the [walk test] key for 2 seconds At two minutes and again at... -
Page 27: Arming With Not-Ready Zones
Arming With Not-Ready Zones The zones in your system are not always ready to arm. For ex- ample, a zone would not be ready to arm if one of its sensors has been vandalized, needs service, or detects a potential alarm condi- tion. -
Page 28: Bypassing
Bypassing To Bypass a Zone: When you manually bypass a zone, the security system func- tions as if that zone does not When a zone is faulted, exist. Bypassed zones are the zone's LED is lit. To not protected. bypass the zone, press the key. -
Page 29: Quick Bypassing
Quick Bypassing To Bypass a Zone with Quick bypassing allows you to Quick Bypassing: bypass zones without entering a user code. This option must When a zone is faulted, the be programmed into your sys- zone's LED is lit. To bypass tem by the installer. -
Page 30: Optional Arming Features
Optional Arming Features Your system offers several optional arming features, described below. Refer to Section 8 to see which features are installed on your system. Extended Exit Delay. This feature automatically resets the exit delay if you re-enter the building while the system is being armed. You may re-enter up to four times;... -
Page 31: Canceling An Arming Sequence
Optional Arming Features (continued) Automatic Home-Arming. Automatic Home-Arming allows you to remain inside a building while its perimeter sensors (such as doors and windows) are armed. Arming begins by entering your user code. If you exit the building during the exit delay, the sys- tem arms both the interior and perimeter zones (full arming). -
Page 32: Entry Delays
Entry Delays Similar to an exit delay, an entry delay is the time you are allowed to enter the building, walk to the keypad, and enter a user code before an alarm sounds. This delay lasts from 10 to 255 sec- onds, depending upon your system's programming. -
Page 33: Automatic (Timed) Disarming
Interior armed _X_ Automatic (Timed) Perimeter armed _X_ Exit allowed _X_ Disarming Requires user code _X_ Automatically arms _X_ No entry allowed ___ Your system can automatically To Change Automatic- Disarming Days: disarm itself at preset times of the day. This option must be Press and hold the programmed into your system [walk test] key for 2 seconds... -
Page 34: Canceling An Alarm
Canceling an Alarm If programmed, your system To Cancel an Alarm: pauses briefly before sounding The Arm LED blinks and an alarm. This gives you the opportunity to cancel a false your system's sirens may alarm. You can cancel the sound. -
Page 35: How To Prevent False Alarms
How to Prevent False Alarms False alarms are more than a nuisance—they reduce the reli- ability of your security system. Here are a few steps you can take to prevent the annoyance and expense of false alarms. 1. Know your system. Make sure all system users under- stand how to arm and disarm, and what special functions they can and cannot do. -
Page 36: Optional Alarm Features
How to Prevent False Alarms (continued) 8. Bypass trouble zones. If you have one or more trouble zones (zones with sensors that may need service), bypass them before arming your system. Have the sensor(s) in- spected if the problem continues. Remember that bypassed zones are not protected. -
Page 37: How To Set The Calendar And Clock
How to Set the Calendar and Clock To Set the Calendar If your system's calendar or clock and Clock: is incorrect, it could result in false alarms. Since many system Press and hold the functions are time-dependent, [clock] key for 2 seconds un- it is important to regularly ad- til you hear two beeps. - Page 38 Calendar and Clock (continued) To convert from 24-hour time The Zone 4 LED lights. En- to 12-hour time, subtract 12 ter the hour of the day, using hours from all times greater two numbers. Be sure to use than 12:00; these are p.m. a 24-hour format (see the times.
-
Page 39: How To Turn The Warning Tone On/Off
How to Turn the Warning Tone On/Off To Turn Tone On/Off: You hear a beeping sound when the system is about to arm, disarm, or sound an Press and hold the alarm. The warning tone re- [pre-warn] key for 2 seconds minds you that time remains to until you hear two beeps. -
Page 40: How To Turn The Backlight On/Off
How to Turn the Backlight On/Off Whenever you use your key- To Turn Backlight On/Off: pad, a light automatically illu- minates the keys. This back- Press and hold the light shuts off 60 seconds after [walk test] key for 2 seconds you have finished using the until you hear two beeps. -
Page 41: How To Change The Relay 1 Days
How to Change the Relay 1 Days Your system can be pro- To Change the Relay 1 Days: grammed with up to four relays Press and hold the that work on the days of the week you specify. The relays [walk test] key for 2 seconds are numbered 1, 2, 3, and 4. -
Page 42: How To Change The Relay 2 Days
Changing Relay 1 Days (continued) To Change the Relay 1 Days (continued): appropriate LED should turn on or off, to reflect the change. To exit, press the key. How to Change the Relay 2 Days To change the Relay 2 days, To Change the Relay 2 Days: follow the procedure to the Press and hold the... -
Page 43: How To Change The Relay 3 Days
How to Change the Relay 3 Days To change the Relay 3 days, To Change the Relay 3 Days: follow the procedure to the Press and hold the right. [walk test] key for 2 seconds until you hear a beep. Enter the master user code. -
Page 44: How To Walk-Test The System
How to Walk-Test the System To Conduct a Walk-Test: A walk-test allows you to test your system's functions without Press and hold the causing an alarm. You should conduct a walk-test once a [walk test] key for 2 seconds week. until you hear two beeps. -
Page 45: How To Use Event Memory
How to Use Event Memory Your system records important To Review Event Memory: events, such as alarms, in Event Memory. You can review Press and hold the Event Memory to monitor the [walk test] key for 2 seconds status of your system. As until you hear two beeps. - Page 46 Meaning Zone LEDs 1 2 3 4 5 6 7 An alarm occurred. 1 2 3 4 5 6 A system device was deliberately damaged. 1 2 3 4 5 6 A sensor was in need of service. 1 2 3 4 5 An alarm condition was corrected.
- Page 47 Meaning Zone LEDs 5 6 7 Not used. 5 6 7 8 A damaged sensor was corrected. 5 6 7 8 An electrical circuit is shorted. (Ground fault.) 5 6 7 A ground fault condition was corrected. A partial power loss occurred (brown out). A partial power loss was corrected.
-
Page 48: How To Test The Bells And Sirens
How to Test the Bells and Sirens To Test the Bells and Sirens: You can test your system's bells and sirens by following Press and hold the the procedure to the right. (See [walk test] key for 2 seconds Note 2 on page 62.) until you hear two beeps. -
Page 49: To Start A Remote Programming Session
To Start a Remote Programming Session To Start A Remote If you have a monitoring sta- Programming Session: tion hookup, your installer may be able to program your secu- Press and hold the rity system through the tele- [walk test] key for 2 seconds phone line. -
Page 50: How To Test The Battery
How to Test the Battery Your system may include a To Test the Battery: backup battery. If it does, the system will continue to function Press and hold the during a power failure, because [walk test] key for 2 seconds it will draw power from the bat- until you hear two beeps. -
Page 51: Common System Messages
Common System Messages Below is an explanation of the common messages your keypad might display. Beside each message is a discussion of what re- sponses are appropriate. If you find the response is ineffective, call your local C&K service representative. You can get more than one error message at a time. -
Page 52: Troubleshooting Service Conditions
Troubleshooting Service Conditions Your system notifies you if a keypad, sensor, or other system component, needs service by lighting the Service LED and by beeping twice every 30 seconds for one minute. To get more information about the service message, press and hold the [service] key for two seconds until you hear two beeps. - Page 53 LEDs Message What to do 1 2 3 5 6 7 8 A wireless keyfob or The second row of zone LEDs remote arming device light in a binary pattern to identify has a low battery. which device has the low battery. To replace the battery, call for service.
- Page 54 LEDs Message What to do 1 2 3 4 5 6 The control panel's If there has been a recent power battery is low. outage, allow the battery to re- charge overnight. If the problem remains, call for service. 1 2 3 4 5 6 The monitoring station If the telephone line is functioning, (phone #1) does not...
-
Page 55: What Areas Do
What Areas Do The S5832 control panel allows you to divide (or "partition") a building into as many as eight areas, regions that can be armed and disarmed individu- ally. Designed primarily for commercial settings, areas can limit an individual's access to portions of a building. - Page 56 can be independently armed and disarmed. In the case of the first building illustrated, an employee can work in the re- pair shop while the showroom, offices, and warehouse are armed. Similarly, in the case of the second illustration, the restaurant can remain open af- ter the other shops are closed and armed.
-
Page 57: How Areas Affect User Codes
Technical Manuals Online! - http://www.tech-man.com... -
Page 58: Pre-Assigned User Numbers
Pre-Assigned Area User Numbers As the table below shows, some user numbers are reserved for specific user types. For example, User 11 is the pre-assigned Kidwatch user number. If programmed, your system automati- cally restricts User 11 to the limited Kidwatch privileges. When your system does not recognize a given user type, the user number functions like other non-reserved user numbers. -
Page 59: How Areas Affect The System
How Areas Affect the System If your building is divided into areas, your LED keypad is assigned to one area only. From the LED keypad, you can only make changes that affect that area alone. This is described in more detail below. -
Page 60: System Configurations
System Configuration Your installer will fill out these pages, to indicate how your sys- tem has been configured. Monitoring Station: ______Yes ______No Maximum Number of Users: ______ Partitioned: ______Yes ______No Keypad assigned to area #:_________________________ Alternate Language: ______________________________ Learning Period (days): ______________ Begins: ________ Check if installed: _____Maid Code _____Quick Bypassing... - Page 61 Temporary Maid Code Hours: ________________________ Kidwatch Time: ___________________________________ Entry Delay #1 __________enter through:_______________ Entry Delay #2: __________enter through:_______________ Exit Delay: ________________________________________ Cancel Alarm Time: _________________________________ Automatic Arming Time: _____________________________ Automatic Disarming Time: ___________________________ Device Connected to Relay 1: _________________________ _________________________________________________ Device Connected to Relay 2: _________________________ _________________________________________________ Device Connected to Relay 3: _________________________...
-
Page 62: Where To Place Smoke Detectors
Where to Place Smoke Detectors One or more of the zones of your security system can be connected to a smoke detector. When installing smoke detectors, we recom- mend that you follow the United States' National Fire Protection Association's guidelines for smoke detector placement. For the best early warning, smoke detectors should be installed in every room. -
Page 63: How To Evacuate In An Emergency
How to Evacuate in an Emergency Every household and business should prepare for a fire by establishing escape routes and regularly practicing escapes. The National Fire Protection Association recommends you take the following steps to develop your own emergency plan: 1. - Page 64 Below is a space to sketch how the building is zoned and/ or divided into areas. Be sure to note how the zones and/ or areas are numbered and labeled. Technical Manuals Online! - http://www.tech-man.com...
-
Page 65: Glossary Of Terms
Glossary of Terms Area: a region of a building that can be that triggers an alarm the instant a sen- armed and disarmed independently of sor detects an alarm condition. the remainder of the building. Monitoring Station: a service that Bypassing: the act of instructing your monitors the status of your security sys- security system to ignore a zone. - Page 66 Notes Some features described in this manual may not be avail- able due to U.L. or local requirements. Contact your in- stallation company for further information. These tests should be conducted on a weekly basis. Con- tact your installation company for your particular require- ments.
- Page 67 Index Alarm Entry delays 28 Maid 14 canceling 30 Event Memory 41 Master User 11 lockout 32 Exit delay 19 relay 16 resetting after 30 Exit termination 26 Temporary Maid 15 silent 32 Extended exit delay 26 with areas 53 Area User codes, using defined 51...
- Page 68 For service on this system, contact: Company: ________________________________ Address: ________________________________ ________________________________ Telephone: ________________________________ ________________________________ Copyright 1998, C&K Systems, Inc. 5-051-532-01 Rev B http:// www.cksys.com Sierra is a registered trademark of C&K Systems C&K is a registered trademark of C&K Components Technical Manuals Online! - http://www.tech-man.com...