Specifications; Common Troubleshooting - AEE Toruk AP10 User Manual

111.ca•
2 Specifications
Quadcopter
Battery 5300mAh LiPo
Weight 1.4kg /3.091bs
Hover Aco.Jracy Horizontal: 2m /6.56fl • vertical: 1m I 3.28ft
Maximum tilt angle
35"
Maximum climb I descant speed Climb: Bm/ s-26.25ft/s; Descand: 5m Is -16.4ftls
Maximum flight speed 20mls - 65.62ftls (Not recommended)
Wheelbase 450mm 11.48ft
Fllghtnme 25m In
Cam•ra
Ambient operating temperature 0-50"C I 32~122"F
sensor Size 112.3
Effective Pixels 16 Megapixels (MP)
Resolution 4608x3456
HD video recording Maximum 1 OBOP /30fps (N system), 1 OBOP /25fps (P system)
Transmitter
Data I Vldeo transfer distance 1000m(3280ft) 1500m (16401t)
Battery duration Bh
Operating current I voltage 150mA/6V
Battery 4MBatteries
R8jMat.r
Operating Frequency 2.4GHz
Communication Distance (open
outdoon~)
300m /984ft
Transmitting Power <=17dBm
Power ConsumpUon 1.5W
3. Common Troubleshooting
3.1 Solution for transmitter Joysticks center (neutral) position errors
When there is a big difference in transmitter Joysticks neutral position, the motors cannot start when performing
esc.
Errors in transmitter Joysticks neutral position
usually occurs in two cases:
1. When Quadcopter is ON and the Joysticks (except throttle) is not in neutral position -Solution: Please move all transmitter Joysticks to neutral position, and re-
start the Quadcoptar, to re-record the neutral position. If the problem persists, It may be caused due to case 2.
2. Transmitter Joysticks is over tuned, leading to a large shift in position, i.e., there is a large asymmetry in transmitter Joysticks position - Solution: Recalibrata the
transmitter.
a) 52 is used to calibrate the left and right joysticks. Toggle 52 to the position 3
(~)
, and tum on the the transmitter. Then move both joysticks clockwise and
countarclockwise twice, ensuring each rotation reaches the maximum degrees. Afterwards, release the joysticks and toggle S2 to the position 1
(@?) .
The
video recording indicator (green) will light up for 3 seconds to indicate the completion
of
the calibration. ··-··
b) RIH!lart the Quadcopter, and ensure the Quadcopter starts properly.
If the problem cannot be solved by the above methods, please send the transmitter back to our factory for repair.
3.2 Quadcopter is invisible and WiFi is disconnected
Tum ofl the transmitter and let the Quadcoptar automatically return. Make sure there are no obstructions on the Quadcoptar's return path, and ensure you are
familiar with the procedures on how to regain control of the Quadcopter.
3.3 WiFi could not be re-connected
This is probably because after the smart devices disconnects from AP10's WiFi connection, the smart devices automatically connects to other WiFi networks. Please
check
to
see if your smart devices is connected
to
the AP10 WiFi network.
3.4. Precautions when multiple smart devices usa the APP at the same time
During flight if the APP is used on one smart devices and then shifted to another smart devices, please make sure you completely log out from the APP in the original
smart devices, so that the APP can function normally on the other smart devices.
3.5 How can you smoothly land the Quadcoptar?
Before performing
esc,
pull down the
Left
Joystick to less than 5%
of
the Joystick level, and then executa
esc.
This
way
you can land the Quad copter smoothly.
23