Download Table of Contents Print this page

Makita 6913D Instruction Manual

Equipped with electric brake

Advertisement

Quick Links

Cordless Impact Driver
CapaCltCeS
MdchinC
screw
Standard bolt
Hiuh tensile bolt
I
I
Equipped with Electric Brake
MODEL 6 9 1 3 D
MODEL 6913DW
With Fast Charger
MODEL 6913DWG
With Fast Charger
INSTRUCTION MANUAL
No load speed
( R P M )
SPEC I F I CAT I
0
N S
4
mm
8
mm 1 5 / 3 2 "
5/16")
5
mm
1 2 mm 1 3 / 1 6 "
112")
5
mm
10
mm
13/16"
~
318")
0
2.200
M a x
fastening
torque
[ S e e
note
1 below)
i m p a c t s per
minuto
~~
Net w e i g h t
Dimensions
IL
x
W
x
HI
0
3,000
voitaqp
I
l"DUt
I
OurDut
I
Charaina t i m e
1 . 6 kg
13.5 l b s l
1 9 4 mm x 79 mm x 2 2 8 mm
1 7 ~ 5 1 8 " x 3 ~ 1 1 8 "
x
9")
1,000
kg
c m
171
f t
. lbsl
1 2
v
I
A
C onlv
5 0 H r
6 0 H z
1
D C 9 . f i V
1 2 V
I
1 Hr
~
Note
1
After fastening high tensile bolt
M12 (F1
1T) for
3
seconds while using a fully charged battery cartridge
2 Manufacturer reserves the right to change specifications without notice
3 Specifications may differ from country t o country
WARNING For your personal safety, READ and UNDERSTAND before using
SAVE THESE INSTRUCTIONS
FOR
FUTURE REFERENCE

Advertisement

Table of Contents
loading

Summary of Contents for Makita 6913D

  • Page 1 Cordless Impact Driver INSTRUCTION MANUAL SPEC I F I CAT I MdchinC screw mm 1 5 / 3 2 " 5/16") M a x i m p a c t s per minuto [ S e e 3,000 1,000 voitaqp Note After fastening high tensile bolt 2 Manufacturer reserves the right to change specifications without notice...
  • Page 2: Important Safety Instructions

    SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT.
  • Page 3 REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed it on. AVOID UNINTENTIONAL STARTING. Don't carry tool w i t h finger on switch. Be sure switch is OFF when plugging in. OUTDOOR USE EXTENSION CORDS.
  • Page 4 SAVE THESE INSTRUCTIONS contains important safety and operating instructions for battery charger. Before using battery charger, read all instructions and cautionary markings battery charger, CAUTION - To reduce risk of injury, charge only MAKITA Battery Cartridge 1200, 1201 & 1201A.
  • Page 5: Additional Safety Rules

    ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature or ABOVE 4OoC (104OF). 2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. 3. Do not allow anything t o cover or clog the charger vents. 4.
  • Page 6 Installing or removing the battery cartridge Always switch off the tool before insertion or removal of the battery cartridge. To remove the battery cartridge, pull out plate on the tool and grasp both sides of the cartridge while withdrawing it from the tool.
  • Page 7 CAUTION : .The fast charger Model DC1201 i s for charging Makita battery cartridge. Never use it for other purposes or for other manufacturer's batteries. When you charge a new battery cartridge or long period of time, does not indicate a problem. You can recharge the battery cartridge fully after discharg- ing it completely and recharging a couple of times.
  • Page 8 NOTE : If the bit is not inserted deep enough into the sleeve, the sleeve will not return to i t s original position and the bit will not be secured. In this case, try re-inserting the bit according to the instructions above. Switch action Tool speed is increased sure on the trigger.
  • Page 9: Operation

    Operation The proper fastening torque may differ depending upon the kind or type of material to be fastened, etc. The relation between fastening torque and fastening time is shown in the figures below. Machine screw lhrl l f t Fastening time High tensile bolt Ky c m...
  • Page 10 Hold the tool firmly and place the point of the driver bit in the screw head. Apply for- ward pressure to the tool to the extent that the bit will not slip off the screw and turn the tool on to start operation. NOTE : Use the proper bit for the head of the screw that you wish to use.
  • Page 11 Always be sure that the tool is switched off and the battery cartridge is removed before attempting t o perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
  • Page 12 ACCESSORIES CAUTION: These accessories or attachments are recommended for use w i t h your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk The accessories or attachments should Size Phillips...
  • Page 13: Cordless Impact Driver

    - 2 0 - ' 9 5 CORDLESS IMPACT DRIVER Model 6913D Note: The s w i t c h and other part configurations may differ from c o u n t r y t o country.
  • Page 14 MODEL 6913D ITEM DESCRIPTION USED MACHINE Ring Spring 11 Flat Washer 12 Compression Spring 13 Sleeve H m " r Case Complete Nylon Washer 14 Steel Ball 3 5 Anvil Steel Ball Hammer Ball 3 5 Steel Flat Washer 22 Compresslo"...
  • Page 15: Recycling The Battery

    ONE YEAR from the date of original purchase. Should any trouble develop dunng this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita's Factory or Authorized Service Centers. If inspection the trouble is caused by defective workmanship or material, Makita will repair replace) without charge.

This manual is also suitable for:

6913dwg6913dw

Table of Contents