KDS Chase 360 Instruction Manual
  1. Manuals
  2. Brands
  3. KDS Manuals
  4. Toy
  5. Chase 360
  6. Instruction manual

KDS Chase 360 Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

INSTRUCTION MANUAL

INSTRUCTION MANUAL
Version No：20150423
Thank you for buying Chase products. Please read this manual
carefully before assembling. We recommend that you keep this
manual for future reference regarding tuning and maintenance.

SAFETY PRECAUTIONS

This radio controlled helicopter is NOT A TOY! It has some technical
requirements, you must pay attention to the flying environment and
correct operation. Never fly your radio controlled helicopter over
people or near crowds. Teenagers must fly under the guardian's guide.
Beginners must fly under the guardian of experienced pilot.

Product Specifications

Length：690mm
Height：200mm
Width：95mm
Main Blade Length：360mm
Tail Blade Length：58-62mm
Motor Pinion：18T/19T
Servo：KDS N300S/T
Motor KV：1900KV
Driving Gear：(18/50)(18/80)
Gear Ratio：18T(12.34:1)
Tail Gear Ratio: 4.73:1
Flying Weight: 1100g
Battery：22.2V 1300-1500mAh
ESC：50A 6S
：
Version No
20150423

Advertisement

Table of Contents
loading

Related Manuals for KDS Chase 360

Summary of Contents for KDS Chase 360

  • Page 1: Instruction Manual

    Tail Blade Length：58-62mm Thank you for buying Chase products. Please read this manual Motor Pinion：18T/19T carefully before assembling. We recommend that you keep this Servo：KDS N300S/T manual for future reference regarding tuning and maintenance. Motor KV：1900KV Driving Gear：(18/50)(18/80) SAFETY PRECAUTIONS Gear Ratio：18T(12.34:1)
  • Page 2 1.INTRODUCTION Congratulations on your purchase of the Chase 360 radio controlled helicopter kit. Chase 360 was designed in Europe by Australia by Glen Kimpton and is proudly manufactured by KDS Model. Our goal was to offer you something different with a minimum of parts, easy maintenance, and outstanding flying performances.
  • Page 3 Page. 2 PREVENT MOISTURE R/C models are composed of many precision electrical components. lt is critical to keep the model and associated equipment away from moisture and other contaminants. The introduction or exposure to water or moisture in any form can cause the model to malfunction resulting in loss of use, or a crash. Do not operate or expose to rain or moisture.
  • Page 4 Page. 3 When you see the marks as below, please use glue or grease to ensure flying safety. “A” Glue width: approx. 2mm “OIL” Lubrication grease. “A” thread lock, apply a small amount on screws or metal parts and wipe surplus off. When disassembling, recommend to heat the metal joint about 15 seconds.
  • Page 5 Page. 4 90mm Centre of Gravity 200mm 96mm 688mm 814mm...
  • Page 6 Page. 5 ITEM NO. DESCRIP TION QTY. Upper motor block Round head screw(M2 5 x 6 Motor mount bracket right Motor mount bracket left Main belt 147MXL-9MM Lower motor block Bearing 4x10x4 18T 2nd Stage pinion 1ST Stage pulley pin 50T Pulley 1ST Stage belt 63MXL...
  • Page 7 Page. 6 ITEM NO QTY. DESCRIP TION Set Screw (M3) Flat head screw M3X6 pinion 18T(19T ) Motor 1880KV This step can be completed at any time. But is easier before installing the 1st stage assembly into the model Make sure your motor has a flat ground on the shaft for the pinion grub screw.
  • Page 8 Page. 7 ITEM NO. QTY. ITEM NO. QTY. DESCRIP TION DESCRIP TION UP Pulley holder SET GYRO TRAY Bearing ( 3x7x3 ) Flat head screw M2. 5X6 Boom Clamp Belt guide pulley CAP Screw (M3 x 24 Down Pulley holder SET Spacer sleeve spacing washer...
  • Page 9 Page. 8 Tip - It is best to position the servo arms on servos ITEM NO. QTY. DESCRIP TION (with 0 trim) closest to level during this step Round head screw (M2 x 6 CYCLIC SERVO Lock Nut Power the servo to adjust the central 15mm Nominal Round head screw (M2.5 x 6) point at level condition before assemble...
  • Page 10 Page. 9 DESCRIP TION QTY. ITEM NO Lipo tray button (right) Round head screw (M2 x 4 canopy locating pin Side frame Recommended lipo 1200 - 1400 mah. Size restrictions 39mm x 45mm x 116mm. Or unlimited length with front tail servo mount option (Refer to Step 26) DESCRIP TION QTY.
  • Page 11 Page. 10 DESCRIP TION QTY. ITEM NO LANDING GEAR - LEFT LANDING GEAR - RIGHT LANDING GEAR MOUNT FROM STEP 6 CAP Screw (M2.5 x 10) lock the screws only after main frame left is well-assembled.
  • Page 12 Page. 11 ITEM DESCRIP TION QTY. FRAME SPACERS Lipo sliding rail right Round head screw (M2 x 4) CAP Screw (M2.5 x 8) CAP Screw (M2.5 x 6) Frame Washer (Red)
  • Page 13 Page. 12 ITEM NO QTY. DESCRIP TION Tail shaft Tail shaft locking collar Set Screw M3x3 Tail Pinion Tail Box Bearings 4x8x3 Ensure no free play in the tail shaft by fastening the Locking collar and pinion against the bearings.
  • Page 14 Page. 13 ITEM NO. QTY. DESCRIP TION Fin Spacer Tail Boom CAP Screw (M2 x 6) Pitch Slider Bracket Tail Belt CAP Screw (M2 x 10) CAP Screw (M2 x 4) CF Vertical stabilizer Tail control guide Heat shrink tubing Tail boom brace mount CAP Screw (ST2 x 6) Tip: Tighten Screws in a few...
  • Page 15 Page. 14 ITEM NO. DESCRIP TION QTY. Parts From Step 4 Tail Belt Parts from Step 10 Boom Clamp...
  • Page 16 Page. 15 ITEM NO. DESCRIP TION QTY. ITEM NO. DESCRIP TION QTY. Parts From Step 5 Front canopy mounting bolt Parts From Step 10 Set Screw (M2.5x10) CAP Screw (M2.5 x 6) Frame Washer (Red)
  • Page 17 Page. 16 ITEM NO. DESCRIP TION QTY. ITEM NO. DESCRIP TION QTY. One way bearing 10x14x6 Parts From Step 1 Bearing 8x14x4 CAP Screw (M3 x 24) First reduction gear Main shaft Bearing 10x15x4 Washer 8x10x0 Auto-rotation gear (50t) Shaft sleeve 10x14x6 Main shaft is symmetrical with no top or bottom.
  • Page 18 Page. 17 ITEM NO. DESCRIP TION QTY. Frame Washer (Red) CAP Screw (M2.5 x 6) CAP Screw (M2.5 x 10)
  • Page 19 Page. 18 ITEM NO. DESCRIP TION QTY. Set Screw (M2.5x10) Frame Washer (Red) Rear canopy mounting bolt CAP Screw (M2.5 x 6) Side frame CAP Screw (M2.5 x 8) Round head screw (M2 x 4) Lipo sliding rail left CF front electronics board CAP Screw (M2.5 x 10)
  • Page 20 Page. 19 note : factory pre-assembled ITEM NO. DESCRIP TION QTY. Oscillating bearing Swashplate Internal Linkage ball A Swashplate Outer ring Swashplate mounting pin Round head screw (M2 x 4) Bearing 20x27x4...
  • Page 21 Page. 20 ITEM NO ITEM NO QTY. QTY. DESCRIP TION DESCRIP TION Washer 5x9x0 CAP Screw (M2 x 10) Bearings 2x5x2 Damper rubber Flybarless linkage arm Main rotor housing Feathering shaft Flybarless swashplate control arm Thrust bearing Washer 2x5x0 Round head screw (M3 x 6) Washer 5x7x0 Main rotor holder...
  • Page 22 Page. 21 ITEM NO. DESCRIP TION QTY. ITEM NO. DESCRIP TION QTY. ITEM NO. DESCRIP TION QTY. Ball link A Set Screw (M2.5x10) Lock Nut Linkage rod (15mm) Ball link B CAP Screw (M3 x 16) Linkage rod (15mm) 30mm 43mm 43mm...
  • Page 23 Page. 22 ITEM NO. DESCRIP TION QTY. Round head screw (M2 x 6) Anti-rotation bracket Anti-rotation bracket mount CAP Screw (M2.5 x 6) Frame Washer (Red)
  • Page 24 Page. 23 ITEM NO. DESCRIP TION QTY. ITEM NO. DESCRIP TION QTY. ITEM NO. DESCRIP TION QTY. CAP Screw (M2 x 5) Flat head screw M2X7 CAP Screw (M2 x 12) Tail rotor T type holder Bearings 3x6x2 Tail blade Thrust bearing Lock Nut Washer...
  • Page 25 Page. 24 ITEM NO. DESCRIP TION QTY. Tail push bearing mount Bearings 6x10x3 E - clip (1.5mm) T type arm Ball link for tail holder Tail push bearing Set Screw M3x3 Note : Factory pre-assembled...
  • Page 26 Page. 25 ITEM NO. DESCRIP TION QTY. ITEM NO. DESCRIP TION QTY. Flange Bearing (2x5x2.5) Tail rocket arm Lock Nut Round head screw (M2 x 4) Washer 2x5x0 Tail control arm Linkage ball A CAP Screw (M2 x 14) Bearing spacer CAP Screw (M2 x 4) Check that the pitch slider fork is square to the shaft and the slider does not bind.
  • Page 27 Page. 26 The Chase 360 has 2 Tail servo ITEM NO. DESCRIP TION QTY. ITEM NO. DESCRIP TION QTY. location options, At the front, high in the frame for Tail Servo Round head screw (M2 x 4) the lowest moment of inertia and optimal CG.
  • Page 28 Page. 27 Build the tail pushrod to suit your desired servo location For rear mount servo Extension for front mount servo Screw reserved for boom brace installation...
  • Page 29 Page. 28 ITEM NO. DESCRIP TION QTY. Note :the boom brace may be mounted in multiple locations. Tail boom brace Tail boom brace end Frame Washer (Red) CAP Screw (M2.5 x 8) CAP Screw (M2.5 x 6) Tail boom brace mount CAP Screw (M2.5 x 10)
  • Page 30 Page. 29 PARTS LIST 1 Main rotor holder arm Main Rotor head block Housing Main rotor paddle clip Radius arm Main rotor holder grips Washout control arm KC-360-002 KC-360-003 KC-360-004 KC-360-006 KC-360-001 KC-360-005 1 x Main Rotor head block Housing 2 x Main rotor paddle clip 2 x Main rotor head 2 x Main rotor holder arm...
  • Page 31 Page. 30 PARTS LIST 2 Tail belt 522MXL-4mm Motor pinion gear18T Motor pinion gear19T Second reduction gear 18T The second level belt 147MXL-9mm First reduction gear50T KC-360-026 KC-360-027-W KC-360-028-W KC-360-030 KC-360-025 KC-360-029-A 1 x Motor pinion gear18T 1x Motor pinion gear19T 1 x Second reduction gear 18T 1 x The second level belt 147MXL-9mm 1 x Tail belt 522MXL-4mm...
  • Page 32 Page. 31 PARTS LIST 3 Main frame mount Linkage Ball Set Ball link set CF Tail boom Canopy mounting bolt Tail boom brace mount KC-360-050 KC-360-051 KC-360-052 KC-360-054 KC-360-049 KC-360-053 10 x Linkage Ball Set 1x Ball link set 1 x CF Tail boom 425mm 2 x Canopy mounting bolt 2 x Main frame mount 1 x Tail boom brace mount...
  • Page 33 Page. 32 PARTS LIST 4 Bearing 3*7*3 Bearing Bearing Bearing Bearing Bearing KC-360-073 KC-360-074 KC-360-075 KC-360-077 KC-360-072 KC-360-076 10 x Bearing 5*10*4 1x Bearing 8*14*4 1 x Bearing 10*15*4 2 x Bearing 3*6*2.5 2 x Bearing 3*7*3 1 x Bearing 8*16*5 Chase Main blade Tall blade 62MM Canopy...
  • Page 34 3.Drive Belt: Agile and KDS uses only top quality, stretch-proof belts. lt is however, impossible to prevent the belt from stretching or wearing out. Check belt tension regularly, and check for the wear on the teeth.
  • Page 35 ...it's time to fly different!!! ： Version No 20150315...

Table of Contents