Table of Contents
Advertisement
CAUTION! WE RECOMMEND THE
USE OF ORIGINAL ACCESSORIES
AND REPLACEMENTS, WHICH CAN
BE PURCHASED FROM
AUTHORIZED DISTRIBUTORS. THE
USE OF OTHER ACCESSORIES AND
REPLACEMENTS INCREASES THE
DANGER OF ACCIDENTS AND IN
THIS CASE THE MANUFACTURER
HAS NO LIABILITY FOR DAMAGES
TO PERSONS AND/OR PROPERTY.
Assembly of nylon string head and blade
Apply the proper guard depending on whether
you plan to use the grass blade or nylon string
head (see chapter: "Application of protective
devices on cutter").
• F1. Apply the nylon string head as shown in the
illustration: a) Protection flange b) Upper plate
c) Guard d) Nylon string head. Tighten by
turning counterclockwise.
• F2. As you tighten, hold the nylon string head
and plate still and insert the wrench or
screwdriver supplied in the holes in the plate
and gearbox; first turn the plate until the two
holes match.
• F3. Apply the blade as shown in the illustration:
a) Protection flange b) Upper plate with blade
centering c) Guard d) Blade with wording and
direction arrow facing upward e) Lower plate f)
Fixed cup g) Blade fastening nut.
F3. CAUTION! Do not use the nylon
string head guard extension (H) with
metal blades.
G1. Double handled grip
The grip (A) can be adjusted to suit the needs of
the operator by moving it forward or backward.
Loosen the knob (C), place the handle in the
desired position then tighten the knob (C) again.
CAUTION! The handle assembly (A)
can be folded parallel to the
transmission shaft to facilitate
transport and storage of the
machine. Loosen the knob (C), turn
the support (B), by 90° clockwise,
fold the handle (A) in the desired
position and tighten the knob (C).
CAUTION! First read chapter "Safety
Precautions"
G. Assembly of grips
H. Starting and stopping the engine
• F4. Make sure the hole in the blade is perfectly
coupled with the centering collar on the upper
plate. Tighten by turning counterclockwise. As
you tighten, hold the blade-plate assembly still
by inserting the wrench or screwdriver supplied
in the holes provided.
F5. "Tap and go" nylon string head
The nylon string head is used to cut grass and
weeds along borders or in zones with obstacles
like walls, fences or trees. It can operate in a very
narrow or uneven zone. The nylon string cuts the
grass neatly without damaging the bark of the
trees or causing violent impact such as due to
the contact of a rigid blade with a hard surface.
Supply of the nylon string
CAUTION! The string cutting blade
housed in the plastic shield will cut
the nylon string to optimum length; a
string that is too long reduces the
rotation speed of the engine and
interferes with cutting efficiency, as
well as increasing the risk of injury.
During cutting, the nylon string wears naturally
causing an increase in the speed of the engine
and a reduced cutting capacity. When this
happens, to bring out more string bump the head
against the ground:
release the throttle trigger to reduce the engine
speed to less than 4000 rpm. Tap gently on the
ground with the button (A) as shown in the figure
and the string will come out automatically.
Accelerate again.
If the string does not come out make sure there
is still some left and try again.
G2. Delta handle
For your safety, fasten the delta handle in front
of the label placed on the shaft at a distance of
at least 11 cm from the rear grip. The handle
should be fastened in a comfortable working
position. The safety pole guard should be
mounted using the accessories supplied and in
the configuration shown in the figure, in contact
with the delta handle.
CAUTION! Start the brush cutter in a
flat place. During startup stand in a
stable position. Make sure the blade
or nylon string head do not touch the
ground or any obstacles.
ENGLISH - 7
Advertisement
Table of Contents
