HP ProLiant series Troubleshooting Manual page 7

Invalid memory types were found on the same node. Please check DIMM compatibility. - Some DIMMs may
not be used .................................................................................................................................. 74
Inter-Controller Link Connection Could Not Be Established .................................................................. 74
Less Than 75% Batteries at Sufficient Voltage .................................................................................... 74
Less Than 75% of Batteries at Sufficient Voltage Battery Pack X Below Reference Voltage........................ 74
Logical Drive X Failed Due to Cache Error ........................................................................................ 74
Logical Drive X Status = Failed ........................................................................................................ 75
Logical Drive X Status = Interim Recovery (Volume Functional, but not Fault Tolerant) .............................. 75
Logical Drive X Status = Loose Cable Detected... ............................................................................... 75
Logical Drive X Status = Overheated ................................................................................................ 75
Logical Drive X Status = Overheating ............................................................................................... 76
Logical Drive X Status = Recovering (rebuilding data on a replaced drive) ............................................ 76
Logical Drive X Status = Wrong Drive Replaced ................................................................................ 76
Loose Cable Detected - Logical Drives May Be Marked FAILED Until Corrected...................................... 76
Mirror Data Miscompare ................................................................................................................ 76
No Configuration for Array Accelerator Board .................................................................................. 76
One or More Drives is Unable to Support Redundant Controller Operation ........................................... 77
Other Controller Indicates Different Hardware Model......................................................................... 77
Other Controller Indicates Different Firmware Version......................................................................... 77
Other Controller Indicates Different Cache Size ................................................................................. 77
RIS Copies Between Drives Do Not Match ........................................................................................ 77
SCSI Port X Drive ID Y Failed - REPLACE (failure message) .................................................................. 77
SCSI Port X, Drive ID Y Firmware Needs Upgrading .......................................................................... 77
SCSI Port X, Drive ID Y Has Exceeded the Following Threshold(s)......................................................... 78
SCSI Port X, Drive ID Y is not Stamped for Monitoring ........................................................................ 78
SCSI Port X, Drive ID Y May Have a Loose Connection....................................................................... 78
SCSI Port X, Drive ID Y RIS Copies Within This Drive Do Not Match..................................................... 78
SCSI Port X, Drive ID Y...S.M.A.R.T. Predictive Failure Errors Have Been Detected in the Factory Monitor and
Performance Data.......................................................................................................................... 78
SCSI Port X, Drive ID Y...S.M.A.R.T. Predictive Failure Errors Have Been Detected in the Power Monitor and
Performance Data.......................................................................................................................... 78
SCSI Port X, Drive ID Y Was Replaced On a Good Volume: (failure message)....................................... 79
Set Configuration Command Issued ................................................................................................. 79
Soft firmware upgrade required....................................................................................................... 79
Storage Enclosure on SCSI Bus X has a Cabling Error (Bus Disabled)... ................................................ 79
Storage Enclosure on SCSI Bus X Indicated a Door Alert..................................................................... 79
Storage Enclosure on SCSI Bus X Indicated a Power Supply Failure...................................................... 79
Storage Enclosure on SCSI Bus X Indicated an Overheated Condition... ............................................... 79
Storage enclosure on SCSI Bus X is unsupported with its current firmware version... ............................... 80
Storage Enclosure on SCSI Bus X Indicated that the Fan Failed... ......................................................... 80
Storage Enclosure on SCSI Bus X Indicated that the Fan is Degraded... ................................................ 80
Storage Enclosure on SCSI Bus X Indicated that the Fan Module is Unplugged... ................................... 80
Storage Enclosure on SCSI Bus X - Wide SCSI Transfer Failed... .......................................................... 80
Swapped cables or configuration error detected. A configured array of drives... ................................... 80
Swapped Cables or Configuration Error Detected. A Drive Rearrangement... ........................................ 81
Swapped Cables or Configuration Error Detected. An Unsupported Drive Arrangement Was Attempted... 81
Swapped cables or configuration error detected. The cables appear to be interchanged... ..................... 81
Swapped cables or configuration error detected. The configuration information on the attached drives... . 81
Swapped Cables or Configuration Error Detected. The Maximum Logical Volume Count X...................... 82
System Board is Unable to Identify which Slots the Controllers are in.................................................... 82
The Redundant Controllers Installed are not the Same Model............................................................... 82
This Controller Can See the Drives but the Other Controller Can't ........................................................ 83
This Controller Can't See the Drives but the Other Controller Can ........................................................ 83
Unable to Communicate with Drive on SCSI Port X, Drive ID Y ............................................................ 83
Contents 7