Table of Contents
Advertisement
S.p.A.
•
Insert the forward gear engagement cable, already assembled with the lever on the slot of the handle, and fix the cable
adjuster to the internal lever support. Then fix the lever by unscrewing the bolt. Reinsert the screw when the lever is in the
support, then screw the nut.
•
Insert the reverse motion engagement cable, already assembled with lever,
following the directions above. The cable of the reverse motion lever is the
more external one (see picture 7 ref. H) in the flask of the handlebar, fit the
cable lever into the lever support marked "MARCIA INDIETRO". Therefore,
the other lever must be fixed on the support marked "MARCIA AVANTI"; fix
the throttle lever to the internal side of the handlebar, blocking it with the nut
assembled on the screw of the throttle lever.
•
Fix the transport wheel to the frame using two special cotter pins that are
assembled on the transport wheel support. The cotter pins must be
withdrawn and inserted again when the wheel is in the wished position on the
frame. (Pict. 5 Ref. "E").
•
Fit the two guard-extensions to the main tiller protections fitted on the body of the machine using the proper screws and
nuts. The protection guards should reach a width of 60 cm according to the CE.
•
During the transport the handle can be left unassembled, by means of the threaded bush that fix it to the handlebar support.
WARNING: Please, read very carefully this booklet before using your cultivator.
Carefully using and servicing this machine, you will certainly get satisfactory
performances for a long time.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT INSIDIOUS OR EVEN FATAL
INJURY.
•
The use of the machine is forbidden to persons younger than 16 years.
•
The operator is responsible of any possible damage and he should always drive the machine carefully and safety.
•
Read this booklet before using the machine for the first time.
•
Before carrying the machine always empty the fuel tank.
•
Before leaving the machine be sure that it is fully stopped.
•
Never use the machine without heavy shoes and long transfers. Always inspect the area where you want to work taking off
stones, branches, cables and any other thing which can be dangerous.
•
Before start working, make sure that a radius of minimum 5 mt. is completely free.
•
Clean any possible leakage of fuel.
•
Fill up when the engine is off and not hot, always in an open space far from fires or any heating source and refrain from
smoking during this operation.
•
Before starting using the machine, make sure that you can quickly stop the engine and that you are familiar with the control
levers.
•
Never allow the engine to run in enclosed spaces where highly toxic carbon monoxide could not evacuate.
•
Never start or use the machine not completely assembled, especially concerning the safety devices and the tiller protection
guards which should always be com pletely assembled with all its extensions. Never start hoeing if the belt protection is not
assembled.
•
Never fix or clean the tiller blades or any other tools when the engine is running.
•
Attention! Don't use the machine on sloping grounds exceeding the lim it indicated in the use and maintenance booklet of
the engine..
•
We are not responsible for accidents due to the wrong use of the machine neglecting the above basic instructions.
Whenever you are starting the engine of the machine, follow these instructions very carefully:
•
Check the oil in the engine : THE BRAND NEW MACHINE IS DELIVERED WITHOUT OIL IN THE ENGINE, THEREFORE
YOU SHOULD FILL IT UP TO THE LEVEL ON THE DIP STICK OF THE OIL CUP.
•
Please read carefully on the booklet the ENGINE USE AND MAINTENANCE concerning the "operations before
starting".
•
Start the engine only in open spaces.
1.
Pull the choke lever on the engine.
2.
Turn the accelerator lever "F" to the "MAX" position (Pict. 8) The switch (Ref. "K" Pict.6) must be "ON".
3.
The clutch levers "G" and "H" must be out. (Pict. 7) Position "A".
4.
Pull the starting rope by the handle "I", firstly smoothly and then strongly: when you feel some resistance don't leave the
handle but help the recoiling of the rope with your hand (Pict. 8).
5.
When the engine runs move the choke lever to the initial position and the accelerator lever in the mid-position (Pict. 6).
6.
For stopping the engine move the accelerator lever "F" in the "STOP" position (Fig.6) or in the "OFF" position "OFF" (Pict.
6 - Ref. "K").
4
SECURITY TERMS
STARTING AND STOPPING THE MACHINE
BL 45
-Picture 5-
Advertisement
Table of Contents
