Qlogic SilverStorm 9020 Quick Start Manual
Hide thumbs
Also See for SilverStorm 9020:
- Specifications (2 pages) ,
- Reference manual (210 pages) ,
- Hardware installation manual (50 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Reference Manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Qlogic SilverStorm 9020
Summary of Contents for Qlogic SilverStorm 9020
-
Page 1: Quick Start Guide
Quick Start Guide S i l v e r S t o r m ™ 9 0 2 0 I N S T A L L A T I O N... - Page 2 Purchasers of OEM products should consult with the OEM for support. Support Headquarters QLogic Corporation 4601 Dean Lakes Blvd Shakopee, MN 55379 QLogic Web Site www.qlogic.com Technical Support Web Site support.qlogic.com Technical Support Email support@qlogic.com Technical Training Email tech.training@qlogic.com North American Region Email support@qlogic.com...
-
Page 3: Pre-Installation Checklist
❑ One (1) Catefogy RJ-11 Serial cable ❑ Power cords (up to 2 total) NOTE: Be certain that the power cords are firmly seated into the SilverStorm 9020 power supplies AC power inlets. ❑ A CD ROM containing: ❑ Technical Documentation ❑... -
Page 4: Installation Tasks
Step 4. Verify that the equipment shipped matches the packing list. Tools and Equipment Required ❑ An ESD wrist strap ❑ A #2 Phillips screwdriver ❑ Pen (felt-tip) to mark the mounting holes on the rack Installation Tasks To perform the actual switch installation, the site implementation engineer must perform the following tasks, which are detailed in this section. - Page 5 Changing the IP Address and Default Gateway Using the RS232 Serial Port Step 1. Connect null-modem/crossover serial cables to the RS-232 ports of the switch. If using a terminal emulation device, the settings should be: ❑ 8 data bits ❑ no parity bits ❑...
-
Page 6: The Switch
Step 5. The system prompts for a password. At the prompt enter: adminpass The system responds with: Welcome to the SilverStorm 9020 CLI. Type 'list' for the list of commands. Step 6. To change the switch default IP address enter: setChassisIpAddr -h ipaddress -m netMask where -h ipaddress is the new IP address in dotted decimal (i.e., xxx.xxx.xxx.xxx) format, and -m netMask... - Page 7 Step 4. From the main menu select OOB LAN IP then Set OOB LAN IP. The following screen is displayed: Figure 1. Set OOB LAN IP Window Step 5. Type in the new switch IP address. Step 6. Type in the new net mask. Step 7.
- Page 8 Installing Documentation from a CD Installing Documentation on a Linux Host Step 1. Place the Documentation CD in the CD-ROM drive. Step 2. Check that the CD has been mounted. Type ls /mnt/cdrom. The system returns a list of files on the CD. Step 3.
-
Page 9: Declaration Of Conformity
QLogic Corporation. 26650 Aliso Viejo Parkway Aliso Viejo, CA 92656 Phone: 949.389.6000 www.qlogic.com QLogic Corporation declares the following product is in compliance with the following standards. Product identification: Name: 2U Multi-Protocol Fabric Director Model/Type: SilverStorm 9020 Standards applied: FCC Part 15, Subpart B, Class A; ICES-003; EMC; EN55022, Class A, EN61000-3-2 and EN61000-3-3; VCCI, Class... - Page 11 Management Suite are registered trademarks or trademarks of QLogic Corporation. All other brands and product names are trademarks or registered trademarks of their respective owners. Information supplied by QLogic is believed to be accurate and reliable. QLogic Corporation assumes no responsibility for any errors in this brochure. QLogic Corporation reserves the right,...
- Page 12 QLogic Corporation 26650 Aliso Viejo Parkway Aliso Viejo, CA 92656 949.389.6000 www.qlogic.com D000010-005 Rev. A...
Need help?
Do you have a question about the SilverStorm 9020 and is the answer not in the manual?
Questions and answers