Advertisement
Quick Links
VCS322SSBI Series / VCS522SSBI Series
Tools Required: Knife or scissors, Phillips or Robertson (square head) screwdriver.
CAUTION: This grill is intended ONLY to be built into an enclosure.
CAUTION: The assembly of this grill requires two (2) people.
WARNING: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly,
lifting or moving the grill is recommended. Protective eyewear and long sleeves are also strongly
recommended.
Assembly Procedures
Model VCS522SSBI Shown
5823
Built In cover
30005823 5/12 Rev. 5 En
Advertisement
Related Manuals for Vermont Castings VCS322SSBI Series
Summary of Contents for Vermont Castings VCS322SSBI Series
- Page 1 Assembly Procedures VCS322SSBI Series / VCS522SSBI Series Tools Required: Knife or scissors, Phillips or Robertson (square head) screwdriver. Model VCS522SSBI Shown 5823 Built In cover CAUTION: This grill is intended ONLY to be built into an enclosure. CAUTION: The assembly of this grill requires two (2) people.
- Page 2 VCS322SSBI/522SSBI Series Assembly Step 1: Unpack Carton and Verify Contents Use a sharp cutting tool to cut the straps on the packaging and then lift off the carton top. The sleeve sur- rounding the barbecue can be removed by lifting it straight up and over the top of the unit. Compare all contents to the parts list and the carton content lists below.
- Page 3 VCS322SSBI/522SSBI Series Assembly Step 1: Unpack Carton and Verify Contents (continued) Bag - Literature VCS500BIC VCS522SSBI Carton Contents CAR242a Box 1 (pt. no. 20304500) x 2 boxes VCS501SSBI contents Cook Grate (2 per box = 4 total) Bag - Literature (pt. no. 30005974) Assembly Instructions VCSBI (pt.no.
- Page 4 VCS322SSBI/522SSBI Series Assembly VCS322SSBI / VCS522SSBI Framing Dimensions When Using Noncombustible Materials Drain Holes (2” diameter) J K L Drain Holes (2” diameter) I N B332 Ref. VCS322SSBI VCS522SSBI B332 31Z\x” (800 mm) 43Z\x” (1105 mm) built in noncombustible specs 3/09 24” (610 mm) 24”...
- Page 5 VCS322SSBI/522SSBI Series Assembly VCS322SSBI / VCS522SSBI Framing Dimensions When Using Combustible Materials (ZC Insulated Jacket Required for Installation) Drain Holes (2” diameter) Drain Holes (2” diameter) O J V K L V V T S S U C L I N ...
- Page 6 VCS322SSBI/522SSBI Series Assembly NOTE: Ensure your grill enclosure has been constructed according to the exact specifications shown in Figure 2. If the en- closure is constructed of wood or other similar combustible materials, the use of the insulated jacket Model VCS301SSIJ or VCS501SSIJ is required.
-
Page 7: Parts Required
VCS322SSBI/522SSBI Series Assembly Step 2: Assemble Fascia Brackets Parts Required: (1) Main Grill Unit (1) Left Fascia Bracket (1) Right Fascia Bracket (4) #10 x 1/2” Bolts (4) #10 Lock Nuts Figure 1 Prop up the front of the grill unit on a 2” or 3” block of wood or some other similar item. Remove the two (2) 1/4-20 x 3/8”... - Page 8 VCS322SSBI/522SSBI Series Assembly Step 3: Assemble the Rear Panel Parts Required: (1) Rear Panel (1) Back Flange (4) Self-tapping Screws Figure 2 Attach the back flange of the rear panel to the grill base with two (2) self-tapping screws. Fasten the ends of the rear panel to the left and right fascia brackets with two (2) self-tapping screws. Figure 2 Rear Panel B363...
- Page 9 VCS322SSBI/522SSBI Series Assembly Step 4: Assemble the Grease Tray Front and Handle Parts Required: (1) Grease Tray Front (1) Handle (with screws) (2) #10 Bolts (2) #10 Nuts Figure 3 Remove the grease tray from the front of the grill base (below the control console). Remove the protective plastic from the grease tray front.
- Page 10 VCS322SSBI/522SSBI Series Assembly Step 5: Install Backligting Batteries and Battery Case into Battery Holder Bracket Parts Required: (1) Battery Case (8) ‘AA’ Batteries NOTE: Eight (8) ‘AA’ batteries are required for all grill models. (Not included) Figure 4 Install eight (8) batteries into supplied battery case, taking care of correct polarity. The battery holder bracket and wire connector are behind the lower left side of the console panel just below the left control knob.
- Page 11 VCS322SSBI/522SSBI Series Assembly Step 6: Assemble the Grill Unit to the Enclosure NOTE: This step should be performed by two (2) persons wearing gloves. Figure 5 Before positioning the grill unit into the prepared enclosure or insulated jacket, depending on the available access, it may be necessary to temporarily disconnect the LP regulator or Natural Gas connector hose from the steel flex line.
-
Page 12: Inside Components
VCS322SSBI/522SSBI Series Assembly Step 7: Install Internal Components and Knobs Parts Required: VCS322SSBI VCS522SSBI (3) Sear Plates (5) Sear Plates (2) Cooking Grates (4) Cooking Grates (1) Warming Rack (1) Warming Rack (1) Smoker Box (1) Smoker Box Figures 6 & 7 Carefully place each of the sear plates side by side inside the grill by making sure the semi- circular finger groove is facing toward the back of the grill. - Page 13 VCS322SSBI/522SSBI Series Assembly Cooking Tips - Smoker Box • To produce more smoke and prevent fast burning, pre-soak the wood chips in a separate bowl of water for at least 20 minutes. • To add wood chips before cooking, fill the smoker box with your choice of flavored chips (remove wood chips from water first).