Table of Contents
Advertisement
Available languages
Available languages
Showing Input Signals
Volume Adjustment/Audio Channel Selection
Volume Adjustment
1
When no menu screen is not displayed, press
For SDI input the "Volume/Embedded Audio" screen appears. For any input other than SDI the "Volume" screen appears.
2
Press
to move the cursor to "Volume".
(This step is skipped when the "Volume/Embedded Audio" screen is not displayed.)
3
Press
to adjust the volume.
4
Press the MENU button to finish.
(The "Volume" screen disappears automatically if no operations are made for 5 seconds.)
Audio Channel Selection
Select the audio channel output from the Speaker (monaural) and AUDIO (MONITOR OUT) (OUT1(L)/OUT2(R))
terminals when an EMBEDDED AUDIO signal is input during SDI input.
●
It is necessary to set the audio channel group in advance. (☞ "Embedded Audio Group" of "Audio Setting"
on page 34)
●
Store the setting for each input of SDI 1 and SDI 2.
1
When the menu is not displayed, use the
The "Volume/Embedded Audio" screen appears.
●
The "Volume/Embedded Audio" screen disappears automatically is no operations are made for about 30
seconds.
2
Use the
buttons to select the left and right channels (L ch/R ch)
3
Use the
buttons to select the audio channel
●
Each time you press a button the audio channel changes according to the "Embedded Audio Group"
setting. (☞ on page 34)
4
Press the MENU button
●
The "Volume/Embedded Audio" screen disappears.
On the Information Display
The monitor displays the information below.
Make the setting to display/hide each information using the MENU with the exception of 5,
●
controlled with T.C. button (☞e on page 28).
1 Audio level meter
●
You can check the conditions of the EMBEDDED AUDIO signals when "Level Meter Display" is set to "Horizontal" or "Vertical."
●
Not displayed when "Level Meter Display" is set to "Off." (☞ "Audio Setting" on page 34)
2 Signal format
●
Displayed when "Status Display" is set to "On." (☞ "Information" on page 38)
●
For the contents displayed, see "Available signals" on page 37 and "On the signal format" below.
3 Source name assigned in "Character Setting"
●
Displayed when "Source ID" is set to "On" or "Auto."
●
Displayed in large letters when "Status Display" is set to "Off" or "Auto."
4 CRC error indication
●
Displayed when "CRC Error" is set to "On." (☞ "Information" on page 38)
●
A red square is displayed when an error occurs.
5 Time code
Press T.C. button (☞ e on page 28).
●
When the input signal includes no time code, "TC – –:– –:– –:– –" is displayed (☞ e on page 28).
●
On the Status Display
If you press the INPUT SELECT button (☞ r on page 28) currently lit, the status of the input signal and setting of MUTING are displayed for about 3
seconds.
●
Make the setting to display/hide the status in "Status Display" of the "Information" (☞ page 38).
●
When "Status Display" is set to "Auto" or "On," the status below is also displayed in the following cases:
– When you change the input
– When the signal condition of the current input changes
– When you turn on the monitor
●
When "Status Display" is set to "On," the signal format will remain displayed 3 seconds after the status is displayed.
1 Signal format
●
For the contents displayed, see "Available signals" on page 47 and "On the signal format" below.
On the signal format
The following messages appear depending on the type of input signals and their conditions.
When a HDMI signal protected with HDCP is input
When no video signal comes in
When a noncompliant video signal comes in
2 Signal format of HDMI and COMPO./RGB input
3 Setting of "MUTING"
• Only appears when in mute mode. (☞ 4 on page 28).
(volume adjustment button).
buttons
(☞ "Information" on page 38)
➔
"*" (at the end of the indication)
➔
"No Sync"
➔
"Out of range"
Volume screen
Volume/Embedded Audio screen
29
Advertisement
Table of Contents
