Table of Contents
Advertisement
Quick Links
MULTI FORMAT LCD MONITOR
DT-E21L4
DT-E17L4G
INSTRUCTIONS
For Customer Use:
Enter below the Serial No. which is located
on the rear of the cabinet. Retain this
information for future reference.
Model No.
: DT-E21L4 / DT-E17L4G
Serial No.
:
The illustration of the monitor is of DT-E21L4.
®
LCT2673-001A
Advertisement
Table of Contents
Related Manuals for JVC DT-E17L4G
Summary of Contents for JVC DT-E17L4G
- Page 1 The illustration of the monitor is of DT-E21L4. For Customer Use: Enter below the Serial No. which is located on the rear of the cabinet. Retain this information for future reference. ® Model No. : DT-E21L4 / DT-E17L4G Serial No. LCT2673-001A...
-
Page 2: Safety Precautions
Safety Precautions The lightning flash with arrowhead symbol, within an equilateral triangle is CAUTION intended to alert the user to the presence of uninsulated “dangerous voltage” RISK OF ELECTRICAL SHOCK within the product’s enclosure that may DO NOT OPEN be of sufficient magnitude to constitute a risk of electric shock to persons. - Page 3 FCC NOTICE CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
-
Page 4: Caution For Use Of The Product For Many Hours
Safety Precautions (cont.) IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. -
Page 5: Table Of Contents
Table of Contents Safety Precautions ............2 IMPORTANT SAFEGUARDS Operating Precautions . -
Page 6: Installation
Installation ● Do not rest your arm on the monitor or lean against the monitor. ● Do not touch the LCD panel when installing the monitor. ● Be sure to install the monitor securely to prevent the monitor from falling over, which may cause damage to the monitor or injury. ●... - Page 7 ● To install the monitor on a wall Caution You can install the monitor on a wall by changing how the stand bottom plate is attached. ● Consult authorized service personnel for electrical work. Using power cords damaged during installation (i.e., exposed or severed Installation Only for Authorized Service Personnel wiring) may result in fire or electric shock.
-
Page 8: Connections
Connections Rear panel Carry handle Use this handle when carrying the monitor. The illustration of the monitor is of DT-E21L4. Security slot Attach a security wire to this slot. 1 POWER switch Turns AC power on or off. button (☞ u on page 10) to use the monitor after turning on the POWER switch. ●... - Page 9 8 E. AUDIO HD/SD SDI (SWITCHED OUT) terminal (BNC) Output terminal for the HD/SD SDI signals. ● The SDI signals of the current input (SDI 1 or SDI 2) are re-clocked, then emitted. ● When an input other than SDI 1 and SDI 2 is selected, the SDI signal of the input selected last time is emitted from this terminal. ●...
-
Page 10: Daily Operations
Daily Operations Front panel Tally lamp This lamp is controlled by the tally function of the MAKE/TRIGGER terminal. • You can select the color of the tally lamp from “Green” or “Red.” You can also select whether the whole lamp is turned on at once, or whether it is turned on one half at a time. -
Page 11: On The Information Display
i DC lamp When the DC 12 V power voltage is being lowered due to the battery consumption, the lamp changes to orange from green. When the voltage becomes lower than a certain level, the monitor automatically turns off and the lamp turns to red. ●... -
Page 12: Menu Configuration
Daily Operations (cont.) On the Status Display If you press the INPUT SELECT button (☞ r on page 10) currently lit, the status of the input signal and setting of MUTING are displayed for about 3 seconds. ● Make the setting to display/hide the status in “Status Display” of the “Information” (☞ page 19). ●... -
Page 13: Menu Transition Diagram
Menu Transition Diagram Main Menu Picture Function Backlight Auto Adjust Aperture H Size Aperture Level H Position Size/Position Adjust V Size V Postion Gamma Dot C ock Aspect Color Temperature Clock Phase sub menu sub menu reset reset Signal Setting Component/RGB Select Auto Aspect Sampling Mode... -
Page 14: Main Menu
Menu Configuration (cont.) Main Menu Picture Function Setting for the picture quality. Item To do Setting value Backlight Adjusts the brightness of the display. –20 to +20 Aperture* Activates/deactivates the function at the level set in “Aperture Level”. Off, On Aperture Level* Compensate the frequency response of the luminance signal of the video signal. - Page 15 Signal Setting Settings for input signals. Item To do Setting value Component/RGB Select Selects the signal type you want to use for COMPO./RGB terminals. Component, RGB Sampling Mode Analog RGB input Standard: When the input signal is VGA60 or XGA60 Wide: When the input signal is WVGA60 or WXGA60 Standard, Wide When the input signal is other than the above, the setting value does not affect the...
-
Page 16: Audio Setting
Menu Configuration (cont.) Audio Setting Settings for the audio output balance, EMBEDDED AUDIO signals and audio level meter signal. Item To do Setting value Balance Adjust the balance between the right and left speakers. L5 – L1, 0, R1 – R5 Audio1 Assign Select the video input through which audio is output. -
Page 17: Set-Up Menu
Sync Function Settings for the synchronization with signals. Item To do Setting value No Sync Action Select the screen status when no signal is coming in. Off, Standby, Power Save (power save mode) Gray Back (gray screen) Delay Time Select the period until the screen status changes as selected in “No Sync Action” after signals 30s, 5min, 15min stop coming in. - Page 18 Menu Configuration (cont.) Picture Sub Adjust Configure the standard level of image adjustment. Item To do Setting value Contrast* Adjust the standard level for the contrast adjusted with the CONTRAST knob on the front –20 to +20 panel. Bright* Adjust the standard level for the brightness adjusted with the BRIGHT knob on the front –20 to +20 panel.
- Page 19 On, Off On: Displayed, Off: Not displayed IMD Protocol Serial communication protocol setting Off, TSL V4.0 Off: Supports JVC protocol, TSL V4.0: Supports TSL UMD Protocol V4.0 Address Address setting 000 to 126 000 to 126: Set a particular address...
- Page 20 Menu Configuration (cont.) ● Setting of “Character Setting” Change the input to one that you want to assign a video source name for. Select “Character Setting”. Press buttons to select the first character. ● Each time you press button, the character changes as follows. Press button to reverse the order.
- Page 21 Function Key Setting Specify the function assigned to the F1/F2 button. ● To display “Function Key Setting” Menu Press the button when the menu is not displayed. Press the MENU button to exit from "Function Key Setting” Menu. Item To do Setting value Function1 Specify the function assigned to the F1 button.
-
Page 22: External Control
External Control About the external control This monitor has three external control terminals. Control priority is as follows. ● Make/Trigger terminal (RJ-45): The following external control Make > Trigger = serial communication = buttons and menu on systems are available. the monitor (1) Make (make contact) system: ●... -
Page 23: Using The Serial Communication
<Functions controlled by the Make/Trigger system> Display Functions to be controlled Opening Short-circuiting – – – No function. — — Tally lamp color selection.* Green Tally Color Tally lamp lighting method selection. Whole One half at a time Tally Type Light the left half of the tally lamp in red.* Tally-L(R) Light the right half of the tally lamp in green.*... - Page 24 External Control (cont.) <Command outline> All commands consist of the following segments. Header Monitor ID Function Data Cr (0Dh) On Header “!” : Operation commands from the personal computer, etc. (☞ <Basic command list> below table). “?” : Reference commands from the personal computer, etc. “@”...
-
Page 25: Troubleshooting
Troubleshooting Solutions to common problems related to the monitor are described here. If none of the solutions presented here solve the problem, unplug the monitor and consult an authorized dealer or service center. Symptom Probable cause and corrective action Page ●... -
Page 26: Self-Check Program
Troubleshooting (cont.) Self-check program This monitor has a self-check function, which allows it to detect malfunctions and alert you. This makes troubleshooting easier. Whenever a problem occurs, one or some of the INPUT SELECT lamps will flash. If this happens, follow the steps below and contact your dealer to resolve the problem. -
Page 27: Specifications
Specifications General Model name DT-E21L4 DT-E17L4G Type Multi format LCD monitor Screen size Type 21 wide format Type 17 wide format Aspect ratio 16:9 Horizontal/vertical frequency 31.469 kHz – 75.000 kHz (computer signal) 49.990 Hz – 75.062 Hz * Some signals within this frequency range may not be displayed (“Out of range” is displayed). -
Page 28: Dimensions
36.7 (1 1/2) 15.1 (5/8) 160 (6 3/8) 88.2 179 (7 1/8) (2 7/8) (2 7/8) (3 1/2) DT-E17L4G 102 (4 1/8) <Front view> <Side view> <Rear view> VESA mounting holes (Size: M4, depth: 10 mm) 430 (17) (2 1/4) 1.3 (1/16) -
Page 29: Available Signals
Available signals The following signals are available for this monitor. Video signals Input terminal Signal format shown in Signal name the status display E.AUDIO * VIDEO analog COMPO. analog RGB HDMI (☞ page 12)* HD/SD SDI NTSC NTSC √ — —... - Page 30 Notice on transportation This monitor is precision equipment and needs dedicated packing material for transportation. Never use any packing material supplied from sources other than JVC or JVC-authorized dealers. ● For easy understanding, pictures and illustrations are shown by being emphasized, omitted or composed, and may be slightly different from actual products.
- Page 31 MEMO...
- Page 32 © 2012 JVC KENWOOD Corporation 0212TMH-MW-MT...