Download
Share
Print this page
Haier PFL510W-u Service Manual
  1. Manuals
  2. Brands
  3. Haier Manuals
  4. Washer
  5. PFL510W-u
  6. Service manual
Haier PFL510W-u Service Manual

Haier PFL510W-u Service Manual

Front load
Hide thumbs

Advertisement

Quick Links

Download this manual
PFL510W-U
Order No.
MODEL: PFL510W-U
2010

Advertisement

loading

Related Manuals for Haier PFL510W-u

Summary of Contents for Haier PFL510W-u

  • Page 1 PFL510W-U Order No. MODEL: PFL510W-U 2010...
  • Page 2 PFL510W-U...
  • Page 3 PFL510W-U...
  • Page 4 PFL510W-U (You will see them in the program introduction table) Signify the program has this course.
  • Page 5 FFL510W-U Extra rinse function:Increase the times of rinse by choosing the function button(at most three times) Quick wash function:For washing slightly dirty clothes to save water power and time Intense wash function:For washing relatively dirty clothes to ensure the washing efficiency Foam self-detect :Automatically add rinse times until the laundry is cleaned when detecting too much foam Eccentric protection :When spinning,if the clothes are not evenly distributed,the washer will fluff out and redistribute the clothes and continue spinning after the clothes distribution becomes...
  • Page 6 PFL510W-U PFL510W-U 54.1 73.8...
  • Page 7 PFL510W-U...
  • Page 8 PFL510W-U...
  • Page 9 SERVICE MANUL PFL510W-U Program knob By turning the knob clockwise/counterclockwise, the required program can be selected. There are 11 programs available. After a program is selected, the corresponding light will go on. Power Switch Press this button to switch on the washing machine. Press it again to switch it off.

  • Page 10: Extra Rinse Button

    PFL510W-U Delay Button Touch this button lightly, the washing machine will start operation after a period of time and the corresponding indicator will go on. The range is 0.5-24 hours; each touch of this button increases a half hour. After the button is set, press the Start/Pause button to start countdown of the set time (the time is displayed on the screen until the program ends).

  • Page 11: Chapter 5 Wiring Circuit

    SERVICE MANUAL PFL510W-U Chapter 5 Wiring circuit Haier Washing Machine...

  • Page 12: Chapter 6 Program Introduction

    SERVICE MANUAL PFL510W-U Chapter 6 Program Introduction sport program syn- Deli- cotton cotton- spin wool cycle -ECO Standard wash cate wash thetic heat wash inlet rinse drain spin inlet rinse drain spin drain spin fluff power off strong other func-...
  • Page 13 SERVICE MANUAL PFL510W-U 1.How to start Press the peed and intens button at the same time, then put the plug in to the socket, wait for about 3 seconds, the LED machine ,then you can press art/paus to let washing machine start test function.
  • Page 14 3.If you want to change the model again after storage, you can cut off the NTC and do the cycle adjustment. 4.Model PFL510W-U you should choose 1050 5.Press On/Off button gently for 2 seconds to switch off the machine as buttons are soft touch sensitive.
  • Page 15 SERVICE MANUAL PFL510W-U Haier Washing Machine...

  • Page 16: Troubleshooting

    SERVICE MANUAL PFL510W-U Error message:Door is not properly shut 20s after program is started. Troubleshooting: Cut off the power and then turn on again. Check the voltage between brown wire and blue wire of door lock, is it between AC 220-240V?
  • Page 17 SERVICE MANUAL PFL510W-U ERR2 Error message:Drainage error,water not emptied within 6 min. Troubleshooting: Check if the pipe connected to the water level pressure is jammed.If it is,clean the Check if water is emptied. pipe.If not,replace PCB Check if drain pump or Check if drain pump acts by drain pipe is jammed.
  • Page 18 SERVICE MANUAL PFL510W-U Error message:Temperature sensor is not properly connected or damaged (display at the end of a program). Troubleshooting: Cut off power and measure the NTC exist open circuit. resistance of NTC by multimeter, Replace it. is it above 1.5 M Check if NTC is connected Connect NTC well.
  • Page 19 SERVICE MANUAL PFL510W-U If the water infilow can not reach the washing water level within 8 minutes. Haier Washing Machine...
  • Page 20 SERVICE MANUAL PFL510W-U Turn on power,and set pre-wash Electromagnetic valve mode,then start.Check the import must be broken,please voltage of electromagnetic valve by replace it. multimeter,is it between AC220 -240V? The wire connected Check if export voltage from PCB to PCB and inlet valve is electromagnetic valve,is it between not properly.Please...
  • Page 21 SERVICE MANUAL PFL510W-U Haier Washing Machine...
  • Page 22 SERVICE MANUAL PFL510-U Haier Washing Machine...
  • Page 23 SERVICE MANUAL PFL510W-U Check if hose-connecting cylind- er to pump is bent or jammed? Haier Washing Machine...
  • Page 24 SERVICE MANUAL PFL510-U Adjust adjustable feet. Replace drainpipe. Haier Washing Machine...
  • Page 25 SERVICE MANUAL PFL510W-U Qu ick Wa sh Pre- Wash Sp o rt 12 0 0 C ot to n Sta n da rd M ix D e lica te 10 0 0 Delay Syn th etic R in se 5 00...
  • Page 26 SERVICE MANUAL PFL510W-U Haier Washing Machine...
  • Page 27 SERVICE MANUAL PFL510W-U Haier Washing Machine...
  • Page 28 SERVICE MANUAL PFL510W-U Dismantle the motor Release the two screws on the Motor bracket. Pull the motor along the arrowhead, then take off the motor. Dismantle shock absorber shock absorber Pull out the pin of shock absorber, then take off the bolt and washer of on the cabinet The pins can not be used again.
  • Page 29 SERVICE MANUAL PFL510W-U Haier Washing Machine...
  • Page 30 SERVICE MANUL PFL510W-U Haier Group Haier Industrial Park, No.1, Haier Road 266101, Qingdao, China http://www.haier.com Haier Front Load Washing Machine...