Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Funkwerk elmeg t240
Summary of Contents for Funkwerk elmeg t240
- Page 2 You can also request this EC declaration of conformity at the following Internet URL: http://www.funkwerk-ec.com. The waste container symbol with the “X” through it on the device indicates that the device must be disposed of separately from normal domestic waste at an appropriate waste disposal facility at the end of its useful service life..
-
Page 3: Table Of Contents
Table of contents Table of contents Installation ..............1 Terminals . - Page 4 Table of contents...
-
Page 5: Installation
Terminals Installation Installation In this chapter, all PABX system ports are described regardless of the expansion of your PABX. The actual expansion will be described on the special pages for the respective PABX. Terminals Terminals can be removed from the pins of the cable terminal bay. Hinweis In all work on the PABX system ports, you must first turn off the PABX electricity supply and put the external sys- tem ports out of operation!! - Page 6 Installation Installation-grade cable or combined as »star-fours«. The individual designations of the wires are firmly allocated to wire defined designations. You must comply with this allocation without exception. Hinweis Never use the additional shielding wire as an earth line. The lines are designated as follows: J-Y(St) Y2x2x0,4: Installation line with plastic insulation, two pairs of wires with a copper cross-section of 0.
- Page 7 Installation-grade cable Installation 1 T568A: white/green green white/orange blue white/blue orange white/brown brown 1 2 3 4 5 6 2 T568B: white/orange orange white/green blue white/blue green white/brown brown 3 Wire designations. Terminal designations for the UAE8 jack. Terminal designations for UAE6 jacks. Terminal designations for UAE4 jacks.
-
Page 8: Fastening Of The Connecting Lines
Installation Fastening of the connecting lines This table shows the different types of connections at an RJ45 or CAT. 5 jack. Access Double wire desig- analog ISDN nations 2-wire 4-wire 802.310BaseT Fastening of the connecting lines Ensure that no more than 100 mm of the sheathing is removed from the lines and that the stranded or twisted wires are led to the terminal bays. -
Page 9: Isdn Bus With Iae Jacks
ISDN bus with IAE jacks Installation ISDN bus with IAE jacks Internal ISDN port of the PABX white black yellow cable Y (St) y2x2x0,6 Internal ISDN port of the PABX J-YY 0,6 Hinweis Please mind the terminating resistors in the last jack. -
Page 10: Isdn-Bus With Rj45-Jacks (Uae)
Installation ISDN-bus with RJ45-jacks (UAE) ISDN-bus with RJ45-jacks (UAE) Internal ISDN port of the PABX white black yellow cable Y (St) y2x2x00.6 Internal ISDN port of the PABX J-YY 0,6 Hinweis Please mind the terminating resistors in the last jack. -
Page 11: Terminating Resistors
Terminating resistors Installation Terminating resistors Hinweis The terminating resistors on the cable terminal bay of the PABX are active when the switch is set to »ON«. When connecting PABXs, modules and jacks, check whether the terminating resistors are fixed, switchable or installed at all. Read the sheets enclosed in the module packaging. -
Page 12: Pabx Terminals
Installation PABX terminals Please note here that you can only connect one installation cable in each LSA Plus insulation piercing terminal, as otherwise there may not be proper contact of the wire. Towards PABX Interconnect these lines! Piercing connecting terminals LSA Plus strip 3 4 5 6 3 4 5 6... - Page 13 Connecting analog terminals Installation RJ45. This jack has 8 contacts (1...8). Connection takes place to the terminals with the designation 4 (a-wire) and 5 (b-wire). The connector of the connection cable has 8 contacts. When selecting jacks, please check whether the connector of the connection cable for your terminal device has 6 or 8 contacts. Terminal 3 4 5 3 4 5...
-
Page 14: Usb Port
Installation USB port France Terminal USB port The PABX system is a full-speed USB terminal device with rates up to 12 MBit/s. Power is supplied to the USB port via the PABX system. The PABX system is a self-powered, category 1.1 full-speed terminal device Connecting options for PABX systems Connecting the PABX to the ISDN network of the network service provider The following figures illustrate the connecting options for the PABX to the external ISDN connection. - Page 15 Internal ISDN connection Installation Internal ISDN connection »Short passive bus« The internal ISDN connection of the pabx is set as a »Short passive bus«. The »short passive bus« has a length of 120 meters. Up to 12 ISDN jacks may be connected in series. You can connect up to 8 terminal devices. Combined, internal terminal devices may have a maximum con- sumption of up to 2 W.
- Page 16 Installation Internal ISDN connection The branches of a star-type wiring are longer than 10 meters: · Terminating resistors must be fitted to the jacks at both ends. The terminating resistors in the PABX system for the correspon- ding connection must be opened. The branches of a star-type wiring are shorter than 10 meters: ·...
-
Page 17: Usb Port
USB port Installation USB port General Information about USB (specification 1.1) USB is the abbreviation for Universal Serial Bus. USB is a serial bus system that allows you to operate various types of devices at one port. This interface can supplement or replace various PC ports (serial, parallel,. . . ). devices at one port. USB is equipped with a standardized API (Application Programming Interface) that is based on the Microsoft Win32 driver model (WDM). -
Page 18: Connecting The Pabx Via Usb To The Pc
Installation Connecting the PABX via USB to the PC Connecting the PABX via USB to the PC Connect the PABX to the USB port of your PC as shown in the figure. Use the USB cable supplied with the system. USB connector (type B terminal device) elmeg T444 USB connector (type A PC/hub) - Page 19 Connecting the PABX via USB to the PC Installation USB cables Data line: Twisted pair (min. 28 AWG) shielded Power supply: non-twisted pair (min. AWG 28), also for shielding Full Speed Maximum length 5 meters Connector: A and B connector Lines: 4 wires (min.
-
Page 20: Index
Index Index Analog terminal devices ....8 Piercing connecting terminals connections ..7 Austria. - Page 21 Index...
- Page 22 Funkwerk Enterprise Communications GmbH Südwestpark 94 D-90449 Nürnberg For information on support and service offerings please visit our Website at www.Funkwerk-ec.com where, you will find a Service / Support area Subject to modifications Ausgabe 4 / 010109...