Advertisement
PAGE II
7. SAFETY NOTES
Please take the time to read these instructions carefully and keep them
to hand in the intended storage compartment
on the child safety seat
13
at all times! The instructions must be with the child safety seat if the latter
is passed on to a third party.
DANGER! For the protection of your child:
• In the event of an accident with a collision speed of more than 10 km/h, the
child safety seat may be damaged without the damage becoming immediately
visible. In this case the child safety seat must be replaced. Please dispose of
it properly.
• As a rule, have your child safety seat checked if it was damaged (e.g if it falls
on the ground).
• Regularly check all important parts for damage. Ensure that all mechanical
parts, in particular, are fully functional.
• Never lubricate or oil parts of the child seat.
•
Never leave your child unattended in the child seat in the vehicle.
• Only allow your child to enter and exit the vehicle on the pavement side.
• Protect the child safety seat from intensive direct sunlight when it is not in use.
The child safety seat can get very hot in direct sunshine. Child skin is sensitive
and could thereby be harmed.
• The more snugly the belt fits over your child's body, the better they will be
protected. Therefore avoid putting thick clothes on your child under the belt.
• Take regular breaks on long journeys in order to give your child the
opportunity to play around.
• Use on the rear seat: Move the front seat forward far enough that you child's
feet cannot hit the backrest of the front seat (to prevent risk of injury).
DANGER! For the protection of all vehicle occupants:
In the case of an emergency stop or an accident, unsecured persons or objects
may cause injury to other vehicle occupants. Please always check that...
• the backrests of the vehicle seats are locked (i.e. that any foldable rear seat
bench latch is engaged).
• all heavy or sharp-edged objects in the vehicle (e.g. on the parcel shelf) are
secured.
• all persons in the vehicle have their seatbelts fastened.
• the child safety seat is always secured when it is in the vehicle, even if no child
is being transported.
WARNING! For your protection when handling the child seat:
• Never use the child safety seat free-standing, not even for test sitting.
• The backrest
14
may tip backward. Always place the child seat on the vehicle
seat before having your child sit down in it.
• When swivelling up the backrest
, nothing must come between the
14
backrest
14
and the seat cushion
15
. You or your child could pinch your
fingers, injuring them.
• To avoid damage, ensure that the child safety seat is not jammed in between
hard objects (car door, seat rails, etc.).
• Keep the child safety seat in a safe place when it is not in use. Do not place any
heavy objects on the seat and do not store it directly next to sources of heat or
in direct sunlight.
CAUTION! To protect your vehicle:
• Certain car seat covers made from more sensitive materials (e.g. velour, leather,
etc.) may sustain signs of wear and tear when using child safety seats. For
optimum protection of your car seat covers, we recommend using the BRITAX
RÖMER car seat protector from our range of accessories.
8. ADJUSTING THE HEADREST
A correctly set headrest
22
ensures that the diagonal seat belt section
optimally positioned, and gives your child optimum protection.
The headrest
22
must be adjusted so that there is a space two fingers wide
between the headrest
22
and your child's shoulders.
To adjust the height of the headrest to fit your child:
1. Reach into the adjustment handle
12
of the headrest
22
and pull it towards you.
12
22
This unlocks the headrest.
2. You can now move the unlocked headrest
the desired height. As soon as you release the
adjustment handle
12
, the headrest
22
into place.
3. Place the child safety seat on the vehicle seat.
4. Have your child sit down in the child safety seat and
22
check the height. Repeat the procedure until the
headrest
has the correct height.
22
9. INSTALLATION
Adjusting the backrest:
The backrest
14
is connected to the seat cushion
an articulated axis. The backrest
14
be adjusted to any inclination of the vehicle seat.
Please know that optimal protection is guaranteed only if
the vehicle seat is in an upright position.
15
A
With ISOFIT + 3-point belt
The
KIDFIX II XP / KIDFIX II XP SICT
is installed permanently in the vehicle with
the ISOFIT locking arms.
Your child is then buckled into the child seat with the vehicle's 3-point seatbelt.
01
1.
If your vehicle is not fitted with ISOFIX insertion aids by standard, clamp
the two insertion aids
02
, with are included in the scope of delivery of the
seat*, with the section pointing upwards to the two ISOFIX fastening points
01
of your vehicle.
TIP! The ISOFIX fastening points are located between the surface and the backrest
of the vehicle seat.
* The insertion aids facilitate the installation of the child safety seat with the
use of the SOFIX fastening points and prevent damage to the car seat covers.
As long as they are not used, remove them and keep them in a safe place. For
vehicles with foldable a backrest, the insertion aids need to be removed before
folding the backrest. Any problems occurring usually come from soiling or ex-
ternal objects on the insertion aids and on the hook. Remove soiling or external
objects to rectify such problems.
2. Moving the headrest of the vehicle seat into the top position.
3. Carry out the steps in Section 8 "ADJUSTING THE HEADREST".
09
4. Hold the ISOFIT
settings button
the ISOFIT locking arms
06
5. Push the green safety button
07
08
button
07
on both sides of the seat towards each
other. This ensures that both hooks on the ISOFIT
locking arms
06
are open and ready to use.
6. Place the XP-PAD
seat closer to the vehicle door.
11
14
7. Guide the elastic holding strap of the XP-PAD
03
into the dark red belt holder
11
until it lies completely in the belt holder
twisted.
8. Place the child safety seat in driving direction on
a vehicle seat approved for use.Ensure that the
backrest
is flush with the backrest of the vehicle
14
seat .
17
is
9. Position the two ISOFIT locking arms
front of the two insertion aids
02
06
10. Push both ISOFIT locking arms
on the back
guides
until the ISOFIT locking arms
02
on both sides with a clicking sound.
DANGER! The green safety button
22
to
visible on both sides so that the child
safety seat is correctly fastened.
will lock
11. Hold the ISOFIT
settings button
the child safety seat as far back as possible.
09
08
12. Shake the child safety seat to ensure that it is
13. Carry out the steps in Section 10 "SECURING
15
by
14
of the child seat can
For the safety of your child, before every journey in the car check that...
the child safety seat is slotted in on both sides with the ISOFIT locking arms
in the ISOFIT fastening points
06
green;
the child safety seat is securely fastened;
16
the lap belt
runs in the bright red belt guides on both sides of the seat
cushion
05
,
16
the lap belt
runs through the bright red SecureGuard
the diagonal seat belt section
18
also runs through the light red belt guide
the diagonal seat belt section
02
the headrest,
XP-PAD
and XP-SICT
11
the diagonal seat belt section
the straps are tight and not twisted,
the seatbelt buckle
18
the seat cushion.
DANGER! If your child try to use to open the vehicle belt buckle
introduce the diagonal belt section
stop as soon as possible. Check whether the child safety seat is correctly
fastened and ensure that your child is correctly secured. Explain to your
child the dangers associated with his actions.
UNFASTENING YOUR CHILD AND REMOVAL:
To unfasten your child or to remove the child safety seat, observe the steps
in Section 6
"
REMOVAL AND DISPOSAL
B
With 3-point belt
The
KIDFIX II XP / KIDFIX II XP SICT
is simply secured together with your child using the vehicle's 3-point seatbelt.
down and push
09
.
06
out in full
1. Carry out the steps in Section 8 "ADJUSTING THE
2. Place the XP-PAD
11
08
and the red release
3. Guide the elastic holding strap of the XP-PAD
14
in the side of the child safety
11
4. Place the child seat on the vehicle seat. Ensure that
03
11
5. Carry out the steps in Section 10 "SECURING
11
of the headrest
03
22
03
and is not
For the safety of your child, before every journey in the car check that...
the child safety seat is securely fastened;
16
the lap belt
runs in the bright red belt guides on both sides of the seat
cushion
,
05
16
the lap belt
runs through the bright red SecureGuard
the diagonal seat belt section
06
directly in
18
also runs through the light red belt guide
.
02
the diagonal seat belt section
of the headrest,
06
into the insert
the diagonal seat belt section
engage
the straps are tight and not twisted,
06
XP-PAD
11
and XP-SICT
08
must be
the seatbelt buckle
18
the seat cushion.
DANGER! If your child try to use to open the vehicle belt buckle
introduce the diagonal belt section
stop as soon as possible. Check whether the child safety seat is correctly
09
down and push
fastened and ensure that your child is correctly secured. Explain to your
child the dangers associated with his actions.
UNFASTENING YOUR CHILD AND REMOVAL:
To unfasten your child or to remove the child safety seat, observe the steps in
REMOVAL AND DISPOSAL
Section 6 "
10. SECURING YOUR CHILD
securely fastened and check again the fastening
buttons
to ensure that both are fully green.
08
YOUR CHILD".
04
and both safety buttons
are fully
01
08
10
.
17
on the side of the vehicle seatbelt buckle
05
of the seat cushion,
17
runs through the dark red belt holder
03
of
are correctly installed and used,
04
17
runs diagonally backward,
must not be positioned on the red belt guide
05
in
17
or
18
17
into the bright red SecureGuard
10
,
16
"
[PAGE I]
05
16
is not installed permanently in the vehicle. It
17
HEADREST".
on the side of the child safety
11
seat closer to the vehicle door.
11
into the dark red belt holder
of the headrest
03
22
until it lies completely in the belt holder
03
and is
03
not twisted.
the backrest
14
is flush with the backrest of the
vehicle seat.
Tip! If the headrest of the vehicle seat gets in the
way, turn it the other way.
YOUR CHILD".
03
10
.
17
on the side of the vehicle seatbelt buckle
05
of the seat cushion,
runs through the dark red belt holder
17
03
17
17
runs diagonally backward,
04
are correctly installed and used,
must not be positioned on the red belt guide
05
in
18
or
17
into the bright red SecureGuard
10
,
17
[PAGE I]
"
KIDFIX II XP SICT:
Unscrew the XP-SICT
04
anti-clockwise (on the side
closer to the vehicle door) until it has a distance of 5
mm to the vehicle door or has been unscrewed to the
maximum.
KIDFIX II XP SICT & KIDFIX II XP:
1. Let your child sit in the child safety seat and place
the XP-PAD
11
over the chest area of your child
2. Pull out the vehicle belt and guide it in front of your
11
child to the vehicle seat buckle
18
.
DANGER! Ensure the vehicle belt is not twisted, as
otherwise the full protective effect of the
retaining system is not ensured.
3. Engage the buckle tongue in the vehicle seat buckle
18
with a CLICK!
18
4. Place the diagonal seat belt section
17
and lap
belt section
on the side of the vehicle seatbelt
16
buckle
18
into the light red belt guide
05
of the seat
cushion.
DANGER! The vehicle seatbelt buckle must not
05
be positioned between the light red belt
guide and the armrest.
18 05
18
5. Also place the lap belt section
16
on the other side
of the seat cushion in the light red belt guide
05
DANGER! The lap belt section
must lie as low
16
as possible over your child's hips on both
sides.
6. Guide the lap belt section
16
into the bright red
10 16
SecureGuard
10
.
DANGER! Do not guide the diagonal the section
into the bright red SecureGuard
10
.
17
7. Guide the diagonal seat belt section
into the dark
red belt holder
of the headrest
until it lies
17
22
03
22
completely in the belt holder
03
and is not twisted.
Tip! If the backrest
14
conceals the belt holder
03
you can adjust the headrest
22
upwards. The diagonal
seat belt section
can now be easily inserted. Now
17
return the headrest
22
to the proper height.
8. Ensure that the diagonal belt
17
runs over the collar-
17
bone of your child and is not on the neck and that
the key on the belt holder is
03
fully closed.
Tip! You can still adjust the height of the headrest
again here in the vehicle.
9. Open the Velcro fastener on the XP-PAD
11
and fold
the top part of the XP-PAD
11
to the side.
17
11
10. Insert the diagonal belt
17
in the die nubby surface
of the XP-PAD
11
.
11. Close the XP-PAD
again by folding the folded
11
part back and closing the Velcro fastener.
DANGER! The diagonal seat belt section
17
must
run diagonally backward. You can adjust
the course of the belt with your vehicle's
adjustable belt deflector.
DANGER! The diagonal belt
17
must never be
directed forwards to the belt deflector
on the vehicle. In this case, use the child
safety seat on the back seat only.
12. Tighten the vehicle seat belt by pulling on the diagonal
seat belt section
17
.
13. Observe the further steps of the relevant installation
type.
.
17
,
22
Advertisement
