Related Manuals for Panasonic K-EW114L03E
Summary of Contents for Panasonic K-EW114L03E
- Page 1 HD IR Weatherproof Fixed Network Camera User’s Manual K-EW114L03E Model No. K-EW114L06E K-EW114L08E Version 1.0.2...
- Page 2 Welcome Thank you for purchasing our network camera! This user’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user’s manual well for future reference!
-
Page 3: Important Safeguards And Warnings
Important Safeguards and Warnings 1．Electrical safety All installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited power source is rated DC12V in the IEC60950-1. (Refer to general introduction) Please note: Do not connect two power supplying sources to the device at the same time;... - Page 4 Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the device.
-
Page 5: Table Of Contents
Table of Contents General Introduction ........................1 Overview ........................1 Features ......................... 1 Specifications ........................ 2 Structure ............................4 Multiple-function Combination Cable ................ 4 Framework and Dimension ..................5 Device Installation ........................6 Installation Steps ......................6 Restore Factory Default Setup Introduction ............. 7 Quick Configuration Tool ...................... -
Page 6: General Introduction
1 General Introduction 1.1 Overview This series network camera integrates the traditional camera and network video technology. It adopts video data collection, transmission together. It can connect to the network directly without any auxiliary device. This series network camera uses standard H.264 video compression technology, which maximally guarantees the video quality. -
Page 7: Specifications
The enclosure conforms to the IP 66 protection. Has the weatherproof function Support dual bit streams, ACF. 1.3 Specifications Please refer to the following sheet for network camera performance specification. Model K-EW114L03E K-EW114L06E K-EW114L08E Parameter Main Processor High performance DSP Embedded LINUX... - Page 8 Weight 500g（Excluding box） Installation Bracket installation Note Panasonic Security Viewer is not supported EMS (E-Series Management Software) & Mobile-EMS do not support i-PRO series NVR Only SXVGA recording is available with i-PRO series NVR See support web page below for further details...
-
Page 9: Structure
2 Structure 2.1 Multiple-function Combination Cable You can refer to the following figure for multiple-function combination cable information. See Figure Figure 2-1 Multiple-function combination cable Port Name Function Connection Note Network port Ethernet Connect to standard Ethernet cable. Power input DC12V Power input port. -
Page 10: Framework And Dimension
2.2 Framework and Dimension Please refer to the following two figures for dimension information. The unit is mm. See Figure 2-2 and Figure 2-3. Figure 2-2 Dimension illustration 1 Figure 2-3 Dimension illustration 2... -
Page 11: Device Installation
3 Device Installation Installation Steps Important • Make sure that the installation area is strong enough to hold the product, such as a concrete ceiling. • Install the camera in the foundation area of the architecture or where sufficient strength is assured. -
Page 12: Restore Factory Default Setup Introduction
Figure 3-2 Device installation 2 Restore Factory Default Setup Introduction Important Please use RESET button when device is running. Slightly press the RESET button to complete the reset function. See Figure 2-3. RESET button Figure 3-3... -
Page 13: Quick Configuration Tool
4 Quick Configuration Tool 4.1 Overview Quick configuration tool can search current IP address, modify IP address. At the same time, you can use it to upgrade the device. Please note the tool only applies to the IP addresses in the same segment. 4.2 Operation Double click the “ConfigTools.exe”... - Page 14 If you want to modify the device IP address without logging in the device web interface, you can go to the configuration tool main interface to set. In the configuration tool search interface (Figure 4-1), please select a device IP address and then double click it to open the login interface.
-
Page 15: Web Operation
5 Web Operation This series network camera products support the Web access and management via PC. Web includes several modules: Monitor channel preview, system configuration, alarm and etc. 5.1 Network Connection Please follow the steps listed below for network connection. ... - Page 16 Figure 5- 2 Web login If it is your first time to log in, system pops up warning information to ask you whether install web plug- in or not after you logged in for one minute. For detailed plug-in installation, please refer to the Web Operation Manual included in the resource CD.
-
Page 17: Faq
6 FAQ I can not boot up Please click RESET button for at least five seconds to restore the device or factory default setup. operate properly. The water leakage The unauthorized front or rear cap remove many result in water occurred. - Page 18 Note This user’s manual is for reference only. Slight difference may be found in user interface. All the designs and software here are subject to change without prior written notice. All trademarks and registered trademarks mentioned are the properties of their respective owners.