Related Manuals for Elmo CRV-24
Summary of Contents for Elmo CRV-24
- Page 1 Instruction Manual Student Response System ＣＲＶ-２４／３２／４０ Please read this manual before using this product. Please retain this manual.
-
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions. plugs, convenience receptacles, and the 2) Keep these instructions. point where they exit from the apparatus. 3) Heed all warnings. 11) Only use attachments/accessories 4) Follow all instructions. specified by the manufacturer. 5) Do not use this apparatus near water. 12) Use only with the cart, stand, tripod, 6) Clean only with dry cloth. - Page 3 (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this equipment not expressly approved by ELMO CO.,LTD. may void the FCC authorization to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
-
Page 4: Important Safeguards
IMPORTANT SAFEGUARDS Follow these guidelines to use the product safely. These "IMPORTANT SAFEGUARDS" indicate important points that should be followed to use this product safely and correctly and prevent damage to the product or other property and injury to you and others. Read carefully before operating the product and retain for future reference. - Page 5 Warning If for any reason smoke comes out of the product, or you notice any unusual odors or sounds, immediately turn off the power switch on the product and remove the batteries. Then remove the wireless adapter from your computer. Continuing to use the product in this condition could result in a fire or electric shock.
- Page 6 Warning Do not apply any heavy impact to the product or throw it. Otherwise the product may be damaged or deformed and shorted and result in leakage, heat, smoke, explosion or fire. Do not use a battery that appears to be damaged or deformed in any way. This could result in leakage, heat, smoke, explosion or fire.
-
Page 7: Usage Precautions
Usage precautions ■ About radio waves used by the clicker The clicker uses radio waves on the 2.4 GHz band. When using the clicker, a radio station license is not necessary. However, please note the following precautions. Do not use the clicker near the following: ■... - Page 8 ■Usage environment / Storage ・The clicker is designed for inside use. Outside use is not recommended. ・Do not place the clicker in any humid, dusty, salt bearing wind, or vibrating locations. ・Use the clicker product under the following environmental conditions: Temperature: 0°C - 40°C (32°F - 104°F) Humidity: 30% - 90% (No condensation) ・When storing the product, do not leave it under direct sunlight or by heaters.
-
Page 9: Table Of Contents
CONTENTS IMPORTANT SAFETY INSTRUCTIONS ................2 IMPORTANT SAFEGUARDS ....................4 Usage precautions ......................7 Before Use ......................... 12 Main functions ......................... 13 Supplied Items ......................... 14 Part Names ........................15 Preparation ........................17 Remove an insulation sheet from the clicker ..............17 Replacing the batteries of the clicker ................ - Page 10 Operation screen of SRS....................41 List of SRS operations ..................... 42 List of SRS buttons ....................... 42 List of clicker operations ....................48 Starting SRS ........................49 From posing a question to close the question ..............51 Finishing SRS ........................57 Group learning .........................
- Page 11 Clicker ........................... 89 Wireless adapter ......................90 Troubleshooting ........................ 91 Specifications ........................92 Product specifications...................... 92 System Requirements ..................... 93 Disclaimer ........................94 About Trademarks ......................94 Repairable Period ......................94...
-
Page 12: Before Use
Image Mate Accent for SRS is designed to allow you to operate SRS functions in addition to the Pen Tablet functions, which are the basic features of Image Mate Accent (IMA). ※For details about the operations of the Pen Tablet, refer to the User’s Guide of ELMO Wireless Slate / Tablet. -
Page 13: Main Functions
■Manage the clicker You can add/ delete a clicker or display the battery level. ■Use with the Document Camera or the Pen Tablet You can pose a question on the spot by using ELMO Document Camera or Pen Tablet (sold separately) . -
Page 14: Supplied Items
Product's package has the following contents. Contact your dealer if any of the following items are not included in the package you purchased. Dry cell AAA battery Wireless adapter Clicker: CRV-CK-1 （Included into the clicker） CRA-1R CRV-24: 24pcs. CRV-24: 48pcs. CRV-32: 32pcs. CRV-32: 64pcs. CRV-40: 40pcs. CRV-40: 80pcs. Screw driver for M3 Carrying Case Seal clicker no. -
Page 15: Part Names
Part Names Power button ■Clicker Turns ON / OFF the clicker. Front Press this button for 3 seconds or longer to turn OFF the clicker. See〈Starting SRS〉. Power LED Indicates the battery charge status. The LED lights up when the clicker is turned on and begins flashing when the battery level is low. - Page 16 ■Carrying Case Cable Storage Pocket Outside Storage for the RGB/USB composite cable supplied with the separately sold Pen Tablet or commercially available RGB cables or USB cables. Double zipper The top of the bag opens 180 degrees. Name holder Name card and the like can be inserted. Shoulder belt The length can be adjusted.
-
Page 17: Preparation
Preparation Remove an insulation sheet from the clicker An insulation sheet is inserted before shipping to avoid the battery exhaustion. Remove the sheet before use for the first time by following the below steps: Remove the battery box cover on the back of the clicker together with the fixing tape. -
Page 18: Replacing The Batteries Of The Clicker
Replacing the batteries of the clicker Use the supplied screw driver to loosen the battery box cover fixing screw. Remove the battery box cover. Make sure to attach the cover after inserting the batteries and tighten the fixing screw. Alkarine dry cell AAA batteries ・Make sure that the polarity (+/-) of the dry cell battery is correct. -
Page 19: Software Installation
Software installation All functions of SRS are controlled by Image Mate Accent for SRS. Install the software before initial use of the SRS. For details about the installation procedure, refer to “Before use” and the following instructions: ■Windows ① Insert the supplied CD-ROM to the CD-ROM Drive of your computer. ②... - Page 20 ■Macintosh(Mac) ① Insert the supplied CD-ROM to the CD-ROM Drive of your computer. ② Select “Mac” in the CD-ROM. Then run “ELMO_IMAforSRS.dmg”. ③ The launcher is displayed. ④ Run “ImageMateAccentforSRS ”. ⑤ Follow the displayed instructions to install. ⑥ Run “ELMOUSBDriver_1.0.0.pkg ”. ⑦...
-
Page 21: Connecting The Wireless Adapter
Connecting the wireless adapter Connect the supplied wireless adapter to your computer’s USB port. Launching Image Mate Accent for SRS Launch Image Mate Accent for SRS launcher by double-clicking the shortcut icon created on the desktop of your computer. SRS launcher PC Annotation mode icon：... -
Page 22: Database Selection
Database Selection In case there are several databases, a database selection window appears when the PC Annotation mode icon or the SRS icon is selected for the first time after starting the Image Mate Accent for SRS. In that case, please select the database to use. Selected database turns to red. -
Page 23: About Image Mate Accent
About Image Mate Accent In this section, you will learn various operation modes of Image Mate Accent (IMA) that can be used through Image Mate Accent for SRS and how to draw lines with mouse. Basic Screen Basic Screen Configuration This section describes the basic configuration of the screen that is displayed when using the SRS. -
Page 24: Various Operation Modes
Various Operation Modes This section describes various operation modes of Image Mate Accent. Diagram of the modes Document Camera mode Document Camera Document Camera image image display Basic operations PC Annotation mode Drawing Deleting Background image Recording Background image selection Computer operations Screen capture... -
Page 25: Pc Annotation Mode
PC Annotation Mode In the PC Annotation mode, you can draw over the computer screen or save the drawing as a picture. Click to enter the PC Annotation mode. PC Operation Mode In the PC Operation mode, you can operate your computer. This mode is used to change the background for the PC Annotation mode or pose questions with SRS. -
Page 26: Teaching Material Import Mode
Teaching Material Import Mode In the Teaching Material Import mode, you can view pictures that you have recorded in advance. Click to enter the Teaching Material Import mode. Selecting Pictures ■ Select a picture that you want to view from the list of saved pictures. Pictures are displayed in order of last updated date. - Page 27 ■ Setting a picture as Favorite Drag & drop a picture to from the Teaching Materials screen. ■ Setting a picture as Background Drag& drop a picture to from the Teaching Materials screen. ■ Register the background shortcuts Press the Background button to show a list of background pictures.
-
Page 28: Drawing Operation
Drawing Operation This section describes how to draw lines with mouse. Drawing Select the desired pen icon in the menu on the top right of the screen. ➊ Select to draw a red line, and select to draw a black line. The initial setting is “pencil (red)”... -
Page 29: Deleting
Deleting ■Partial deletion If you only want to delete part of a drawing, align the cursor with the area that you want to delete, and move the mouse while pressing the right button of the mouse. You cannot partially delete a line that was drawn continuously. Caution ■Delete all Select... -
Page 30: Recording A Lesson
Recording a Lesson ■ Saving a picture ➊ Display the image that you want to save as a picture. ➋ Select to save the picture. ・ For information on how to check the saved picture, see〈 Selecting Pictures〉 Caution... - Page 31 Recording a video ■ ➊ Display the image that you want to record as a video. ➋ Select on the main menu. The Recording Setting window appears. The recording format can be selected between High (H.264) and Standard (MJPG). An interval recording system is used for the recording. The recording interval can be set from 1 second to 24 hours.
-
Page 32: Operating The Document Camera
Operating the Document Camera Operate the Document Camera by touching on the main menu. The presented Document Camera image can be paused by clicking and flipped vertically by clicking Document Camera operation buttons To control the zoom level of the Document Camera. Zoom In/Out To focus the Document Camera automatically. -
Page 33: Mask Function
Mask Function The mask hides part of or whole Document Camera image that is displayed. By temporarily hiding part of the image that you do not want to show while asking questions or giving explanation, your lessons will become more effective. Select on the sub menu. -
Page 34: Highlight Function
Highlight Function The highlight function brings attention to a part of the Document Camera image. By highlighting only the area you want to bring to attention, your lessons will become more effective. Select on the sub menu. The highlighted area is displayed on the screen. Drag the highlighted area to move it. You can change the size of the highlighted area by dragging the non-highlighted area. -
Page 35: Scroll Function
Scroll Function The scroll function enlarges the Document Camera image. By temporarily enlarging a small part and moving the image with the pen, your lessons will become more effective. Select on the sub menu. An electronically magnified image is displayed on the screen. Drag the image to move it. To cancel the scroll, select on the sub menu again. -
Page 36: Using Powerpoint Support Function
Using PowerPoint Support Function Start PowerPoint while the Image Mate Accent for SRS is running. Start slideshow in PowerPoint. Then set the Image Mate Accent for SRS to the PC Annotation mode or the SRS mode. The PowerPoint Support icon appears in the bottom left of the screen. You can move to the previous page by pressing or to the next page by pressing PowerPoint Support icon... -
Page 37: Setting The Pen
Setting the Pen Select to display the pen settings. ➊ To select the pen that you want to configure. Pen 1 / Pen 2 To select a type for the selected pen. Pencil Draw a line with the set line thickness. Marker Draw a line with the set line thickness. -
Page 38: List Of Menu Icons
List of Menu icons To select pen 1. The initial setting is a red pencil. You can change the Pen 1 settings for this pen in "Pen Settings". To select pen 2. The initial setting is a black pencil. You can change the Pen 2 settings for this pen in "Pen Settings". - Page 39 To redo the last editing operation (such as drawing with the pen or deleting with the eraser). There is a limit on the Undo number of operations that can be undone. To change the pen to a pointer. Select To record the contents displayed on the screen as a video. An interval recording system is used for the recording.
- Page 40 To bring attention to a part of the Document Camera image. You can move the highlighted area by dragging it. Highlight In expert mode, you can change the size of the highlighted area by dragging the non-highlighted area. To digitally enlarge the Document Camera image. Use it to enlarge the area that is too small.
-
Page 41: Using Srs
Using SRS Operation screen of SRS Operations such as posing questions, giving answers and displaying the results are performed from the SRS control panel. IMA menu icon SRS icon SRS Setting Menu SRS control panel Buttons Buttons IMA sub menu icon... -
Page 42: List Of Srs Operations
List of SRS operations List of SRS buttons Following command buttons in the SRS control panel are used to pose questions or display the results. ■Before Testing（The color of the SRS control panel turns to blue.） （Starting screen） Group settings button Iconize button Start Testing button Countdown Timer button... - Page 43 （Countdown Timer screen） Minute/ Second selection Start Testing button button Countdown Timer Close button Increase / Decrease button Menu button Name Function Start Testing To start receiving responses. The Countdown Timer starts automatically at the same time. Countdown Timer To display the set time. （The drawing shows an example when the timer is set to 1 min.）...
- Page 44 ■Testing is Open（The color of the SRS control panel turns to green.） （Open Testing screen） Close Testing button Number of responses Start Testing button Menu button Name Function Number of To display the number of clickers responses responded. By selecting this button, the unanswered clickers can be displayed.
- Page 45 （Countdown Timer screen） Minute/ Second selection button Pause button Countdown Timer Close button Increase / Decrease button Menu button Name Function Pause To pause the Countdown Timer. When this button is selected, the screen changes to “Start Testing”. Select the “Start Testing” button to restart the countdown.
- Page 46 ■Displaying the results（The color of the SRS control panel turns to blue.） （Results screen） Display Results button Speed Ranking button Display Group Results button Start Testing button Response buttons Menu button Name Function Display Results To display the results by clicker. Return to the question screen when the results are displayed.
-
Page 47: Setting Menu
■Setting menu Select the menu button before posing a question. Review button Menu button Award button Report button Settings button Menu button Name Function Review To display (review) the questions and the results in the session. See〈Review of the session〉. Award To display the Award screen. -
Page 48: List Of Clicker Operations
List of clicker operations These buttons are used to respond to the questions or cast a vote. Button Name Function Power button To turn ON/OFF the clicker. The power LED lights up when the clicker is turned on. Press the button for 3 seconds or more to turn off the clicker. -
Page 49: Starting Srs
Starting SRS SRS can be started either from the respective modes in Image Mate Accent for SRS or by launching the application from your computer screen. N o t e Refer to 〈About Image Mate Accent〉 for details about modes and operations other than SRS functions. - Page 50 ➋ Turn on the clicker. Press Power button to turn on the clicker. The power LED lights up and the clicker attempts to establish the wireless connection with your computer. N o t e When the battery level is low, the power LED flashes for 5 seconds. In that case, replace with new batteries.
-
Page 51: From Posing A Question To Close The Question
From posing a question to close the question Pose a question using the Document camera or your computer screen. Then open Testing by selecting the Start Testing button in the SRS control panel or one of “[2]～[6],[T/F]” buttons in the Response Sub Buttons. N o t e The entire process from starting Image Mate Accent for SRS to finishing it is called “session”... - Page 52 ➌ Respond to the question by using the Response buttons on the clicker. Respond to the question by pressing the Response buttons on the clicker. Selected button flashes for max.7 seconds when sending a response and lights up for 5 seconds if the response is successfully accepted.
- Page 53 Check the number of clickers responded. When the Number of responses is selected, the Unanswered Clickers screen is displayed to check the clickers that did not respond to the question. Also, you can configure the “Answer in place of the student” or “Absent” settings. Unanswered Clickers Clear Unanswered screen.
- Page 54 ➍ Close Testing. Close Testing Close Testing with the Close Testing button The color of the SRS control panel changes to blue. N o t e You can annotate on the screen using annotation functions after Testing is closed. ➎ Display the results.
- Page 55 ■Shrink the results screen When the Shrink Window button is selected, the results are displayed as a window at the bottom left corner over the question screen. The results window can be moved freely by dragging it. When the Full-screen button is selected, the results are displayed in full screen. Press the Close button to close the results display.
- Page 56 ■Speed Ranking The clicker number (student Switches between the clicker number number) and the nickname display and the nickname display (if registered) are displayed. Select the number of students to be displayed at a time (Top 5/ 10/ 15/ 20). The drawing shows an example when Top 5 is selected.
-
Page 57: Finishing Srs
Finishing SRS ➊ Turn off the clicker. When Power button of the clicker is pressed for 3 seconds or longer, the clicker is powered off and the power LED goes off. N o t e The clicker automatically enters standby status when there is no wireless communication. -
Page 58: Group Learning
Group learning You can show the results by groups by grouping clickers during a session. ➊ Configure group settings. Select the Group setting button to display the Group setting window. Configure group number and group type. You can also change respective group name (group symbol). - Page 59 ➋ Join in a group. Join in a group by pressing one of the Response buttons on the clicker. Press one of these buttons to join in a group. Press a button with the same number as the group you intend to join in. Your clicker number is displayed inside group box.
- Page 60 ➌ Finalize the group settings. Finalize the group settings with OK button and the Setting window is closed. ➍ Ask a question and display the results. The whole process from asking a question, starting Testing, closing Testing to displaying the results is same as basic procedure.
-
Page 61: Review Of The Session
Review of the session You can review the questions posed during the session. Prepare the review. ➊ Review button Select the Review button from the settings menu to change the SRS control panel to review mode. ➋ Display the question screen. Select a question in the session by using the Move button to display the question screen. -
Page 62: Giving An Award
Giving an award In each session, you can select one student to give an award. The Award screen can be saved. ➊ Enter names of recipient and sender. Select the Award button to display the Award screen. Enter names of recipient and sender by using the drawing function. Pen icon Date is Enter the name... -
Page 63: Utilizing The Collected Data
Utilizing the collected data With ELMO SRS Reporting, the collected data that is saved on your computer can be displayed or converted into a format readable on other computers. Using Result Display Software Starting the software Select a report from the menu in the SRS control panel to launch SRS Reporting. -
Page 64: Displaying The Session Report
Displaying the Session report The entire process from starting Image Mate Accent for SRS to finishing is called a “session”. A list of questions in a session and details of the results of each question can be viewed. ➊ Display a list of sessions. A list of saved sessions is displayed after the [Session Report] tab is selected. - Page 65 ➋ Display a list of questions. Select a session in the session list that you wish to view. The selected session turns blue. Press the Select button to display a list of questions in the session. Items to be displayed in the list of questions： （Date and Time／Question Image／Number of Students／Accuracy／Number of choices／...
- Page 66 ➌ Draw over the question screen. You can draw over the question screen by double-clicking a question image. 8 different pens(Black, Red, Green, Blue, Cyan, Magenta, Yellow, White) are available. Eraser button Pen buttons Undo button N o t e The software asks whether to save the annotations once the close button is pressed.
- Page 67 ➎ Print a report. Contents of a report can be printed. Select [PRINT] button while a report is displayed. N o t e The printer needs to be installed on your computer. Date・Time Question screen （Saved screen with added annotations are displayed.）...
-
Page 68: Output The Personal Report
Output the personal report Review the personal results from the saved record. ➊ Display the list of sessions. Select the [Personal Report] tab to display the list of sessions. The sessions displayed in the list first are the latest saved session and other sessions saved in the same month as the latest saved session. -
Page 69: Saving In Other Formats
Saving in other formats The collected results can be saved by session in csv/ xml/ xel and xls formats. Select [Export] from [Menu] while a list of sessions (or questions) are displayed. Select [Export] after specifying a date, save format and a destination folder from the dialogue displayed. -
Page 70: Various Settings
Various Settings In this section, you will learn how to configure SRS. Wireless setting for the clicker If the wireless connection cannot be established after pressing Response buttons (the “Response button LED” continues to flash) perform the wireless setting using the "Wireless setting button”... -
Page 71: Image Mate Accent For Srs Configurations
Image Mate Accent for SRS Configurations With ELMO SRS Configurations, Image Mate Accent for SRS can be configured. Starting the software Select “Configurations” from “Menu” in the SRS control panel. N o t e ELMO SRS Configurations can also be launched from [Start]-[Program Files]-[ELMO]-[Image Mate Accent for SRS]-[ELMO SRS Configurations]. -
Page 72: Settings
Settings The destination to store the data created by Image Mate Accent for SRS can be set. ① ① Contents location The destination to store the contents created by Image Mate Accent for SRS and the folder to add stamps and background images can be set. The destination to store the contents can be configured by pressing the Browse button. -
Page 73: Srs Settings
SRS Settings Image Mate Accent for SRS can be configured from “SRS Settings”. ① ② ③ ④ ⑤ ① Database Location The destination to store the database used by Image Mate Accent for SRS and the records of SRS can be set. The destination to store the SRS records can be configured by pressing the Browse button. - Page 74 ② Timer Settings The initial setting of the timer can be set in increments of 10 sec. between 10 sec. and 60 sec. and in increments of 60 sec. between 60 sec. and 300 sec. using up/down buttons. N o t e Default setting of the timer is 60 sec.
-
Page 75: Software Update
Software update The automatic update for the software can be set. N o t e Access our update page to verify you are running the latest version of the software. You need to have an internet connection to update your software. ①... -
Page 76: About
② Proxy setting You can use the software with default settings. When you need to configure this setting, put a tick mark in “Use Proxy Server”. Tick here. N o t e Consult your internet administrator or provider for details as to the configuration. About You can see the detailed information of the software. -
Page 77: Srs Data Settings
SRS Data Settings With ELMO SRS Reporting, you can manage the student’s data and the clicker. Starting the software Select a report from the menu in the SRS control panel to start SRS Reporting. Then select the “SRS” tab. N o t e ELMO SRS Reporting can also be launched from [Start]-[Program Files]-[ELMO]-[Image Mate Accent for SRS]-[ELMO SRS Reporting]. - Page 78 ■Clicker Menu button Name Function Check To check the wireless connection. Connection Battery level To display the last used time and the battery level. Clicker Information To associate the clicker with a student or add/delete the clicker. ■Register Menu button Name Function Register...
-
Page 79: Check The Connection
Check the connection The wireless connection with the registered clicker can be checked. Press a button of the clicker that you want to check after connecting the wireless adapter to your computer. Device ID, the button that is pressed, the battery level and the clicker version are displayed. -
Page 80: Battery Level
Battery level The last used time and the battery level for all the registered clickers can be displayed. Last connected time Battery level: Good：The battery level is enough. Low：The battery level is low. Replace the batteries when “Low” is displayed. Caution N o t e Perform the〈Check the connection〉to see the current battery level. -
Page 81: Clicker Information
Clicker Information When the wireless adapter is connected, the Device ID, the clicker number and the student’s information (if registered) are displayed. You can also add or change the clicker here. N o t e Connect the wireless adapter to your computer before performing the above operation. The row of the specific clicker ID’s can be selected by pressing any buttons on the relevant clicker. -
Page 82: Register Students Information
The students’ information can be registered. Pay strict attention to the protection of the personal information and the right of publicity of the students. ELMO is not responsible for any loss or leak of Caution the personal information of the students in relation to the use of SRS. -
Page 83: Let's Take Photos
Let’s take photos! You can take a picture of the student for the student information by using the Document Camera. Connect the Document Camera to your computer and switch it on. Select the clicker number under which the picture is registered. Then press the “Let’s take photos!”... -
Page 84: Database Settings
Database Settings Create Database When the Create Database button is selected, a new database or a copy of the existing database is created. Enter the name of the database to create. Enter the description of the database to create. Tick here to refer to the existing database. -
Page 85: Select Database
Select Database When the Select Database button is selected, the default database can be set. The name of the current database The student’s information of the is displayed. selected database is displayed. Select a database. The description of the selected database is displayed. -
Page 86: Edit Profile Of Database
Edit profile of database By selecting the Edit profile of database button , you can edit the name and the description of the registered database. Select the database you wish to edit, then edit the name and the description. Press the OK button after finishing the edit. Select the database. -
Page 87: Adding Or Changing The Clicker
Perform the wireless setting for the added clicker. Establish the wireless setting between the added clicker and the wireless adapter. Refer to 〈 〉 in Various Settings for details. Wireless setting for the clicker Launch ELMO SRS Configurations. ➋ Clicker Launch the configuration software. Information Select the Clicker Information button the “SRS”... - Page 88 ➍ Select the clicker to be replaced. Select the Overwrite button. The Device ID of the added clicker turns to green from blue. Select the Device ID of the clicker to be overwritten (deleted) from the list by using a mouse. The color of the Device ID of the relevant clicker turns to grey.
-
Page 89: Other Function
Other Function About LED The power LED, the Response buttons LED and the wireless setting button LED on the wireless adapter indicate the condition of the respective devices. Clicker ■Power LED (Red) LED status Condition The power is off. Press the power button to turn on the power. The power is on. -
Page 90: Wireless Adapter
※The interval of flash changes depending on the condition of the communication. High-speed The Wireless setting button is pressed. flashing For details about other LED status than starting SRS when using with Elmo Pen Tablet CRA-1, refer to the User’s Guide of ELMO Wireless Slate/ Tablet. Caution... -
Page 91: Troubleshooting
Is the wireless setting between the adapter supplied with SRS needs to be set before you use Pen Tablet and the wireless adapter your Pen Tablet with SRS. Refer to User’s Guide of ELMO Wireless Slate/ Tablet for the completed? wireless setting. -
Page 92: Specifications
Storage Temperature -20°C - 60°C (-4°F - 140°F) Number clicker compartments Number of Pen Tablet storage External Dimensions L425(16 47/64”)×W365(14 9/16”)×H165(6 1/2”)（mm） CRV-24:3.2kg(7.1lb) (Clicker x 24pcs.) CRV-32:4.0kg(8.9lb) (Clicker x 32pcs.) Weight CRV-40:4.8kg(10.6lb) (Clicker x40pcs.) ※（Including 1pce. wireless adapter and accessories）... -
Page 93: System Requirements
System Requirements The SRS can be used in the following computer environments. Computer model IBM PC/AT compatible Operating system ■Windows (OS) Microsoft Windows XP Home Edition / Professional SP2 Microsoft Windows Vista Home Basic / Home Premium / Business / Enterprise / Ultimate SP1 Microsoft Windows 7 Starter / Home Premium / Professional / Ultimate 64-bit versions supported (excluding Windows XP 64-bit... -
Page 94: Disclaimer
The software already installed in your computer or other devices connected to your computer may affect the performance of Image Mate Accent for SRS. ELMO is not liable for any direct or indirect damages resulting from the use of Image Mate Accent for SRS. - Page 95 OVERSEAS SUBSIDIARY COMPANIES ELMO USA CORP. Headquarters 1478 Old Country Road Plainview, NY 11803-5034, U.S.A Tel:(516) 501-1400 Fax:(516) 501-0429 E-mail: elmo@elmousa.com Web: http://www.elmousa.com West Coast Branch Cypress Pointe Business Park 5676 Corporate Avenue Cypress, CA 90630, U.S.A Tel:(714) 828-8457 Fax:(714) 828-8429 ELMO Europe SAS Immeuble Elysées la Défense,...