Bunn MHG Installation & Operation Manual
  1. Manuals
  2. Brands
  3. Bunn Manuals
  4. Coffee Maker
  5. MHG
  6. Installation & operation manual

Bunn MHG Installation & Operation Manual

Hide thumbs Also See for MHG:

Advertisement

Table of Contents

See also: Service & Repair Manual
RELEASED FOR PRODUCTION
MHG
for use with
Smart Funnel
®
S/N MHG0015000 & UP
INSTALLATION & OPERATING GUIDE
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601
FAX: (217) 529-6644
To ensure you have the latest revision of the Operating Manual, or to view the Illustrated Parts
Catalog, Programming Manual, or Service Manual, please visit the Bunn-O-Matic website, at
www.bunn.com. This is absolutely FREE, and the quickest way to obtain the latest catalog and
manual updates. For Technical Service, contact Bunn-O-Matic Corporation at 1-800-286-6070.
36529.0001D 10/14 ©2011 Bunn-O-Matic Corporation
DIR Num: 36529.0001
25, November 2014

Advertisement

Table of Contents
loading

Related Manuals for Bunn MHG

Summary of Contents for Bunn MHG

  • Page 1 To ensure you have the latest revision of the Operating Manual, or to view the Illustrated Parts Catalog, Programming Manual, or Service Manual, please visit the Bunn-O-Matic website, at www.bunn.com. This is absolutely FREE, and the quickest way to obtain the latest catalog and manual updates. For Technical Service, contact Bunn-O-Matic Corporation at 1-800-286-6070.
  • Page 2 AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND. In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities or services, or any other special, incidental or consequential damages.

  • Page 3: Table Of Contents

    #37881.0000 DAMAGE, FIRE, OR SHOCK HAZARD READ THE ENTIRE OPERATING MANUAL INCLUDING THE LIMIT OF WARRANTY AND LIABILITY BEFORE BUYING OR USING THIS PRODUCT 20545-0000D 01/04 © 1990 Bunn-O-Matic Corporation #20545.0000 00824.0002 36529.1 103111 DIR Num: 36529.0001 25, November 2014...

  • Page 4: Electrical Requirements

    RELEASED FOR PRODUCTION ELECTRICAL REQUIREMENTS Refer to Data Plate on the Grinder, and local/national electrical codes to determine circuit requirements. This grinder has an attached cordset and requires 2-wire, grounded service rated: 120 volts ac, 15 amp, single phase, 60 Hz, for domestic grinders. 220-240 volts ac, 10 amp, single phase, 50 Hz, for most international grinders.

  • Page 5: Initial Set-Up & Programming

    RELEASED FOR PRODUCTION INITIAL SET-UP & PROGRAMMING 1. Grinder will not operate unless a hopper with a coffee name programmed into the chip is in place on the grinder. 2. Refer to Setup Menu “NAME HOPPER” to program hopper chip. 3.

  • Page 6: Cleaning

    5. Clean and sanitize the hoppers and lids. Care should be taken not to scratch the hoppers with any abrasive materials. NOTE - Bunn-O-Matic recommends the 3-step method for cleaning and sanitizing the hoppers and lids. The 3-step method consists of hot soapy water using an approved detergent, a fresh water rinse, and an aqueous sanitizing solution using an approved non-chlorine sanitizer.

  • Page 7: Coffee Grinding

    RELEASED FOR PRODUCTION COFFEE GRINDING 1. Visually inspect the selected hopper for an ample supply of whole bean coffee. 2. Place a paper filter into the brew funnel. The filter must not be folded-over or tilted to one side. 3. Insert the funnel into the funnel rails and push until it stops. 4.

  • Page 8: Communicating With The Grinder

    RELEASED FOR PRODUCTION COMMUNICATING WITH THE GRINDER To Write A Name To A Hopper PRESS AND HOLD RIGHT HIDDEN BUTTON TO ENTER THE SET-UP MENUS NAME HOPPER? WHICH SIDE? LEFT DONE RIGHT REVIEW RECIPES Page 10 "COFFEE NAME" PRESSING EITHER "PREV" OR "NEXT"...

  • Page 9: Dir Num: 36529.0001

    RELEASED FOR PRODUCTION COMMUNICATING WITH THE GRINDER (Continued) Timer Adjustment (Control Board) Three different batch settings are selectable for each hopper. Each batch is independently adjustable by setting the length of time a slide gate opens to allow beans to drop into the grinding chamber. A second time setting for each batch determines how long the grind motor continues to run after the slide gate closes.

  • Page 10: Dir Num: 36529.0001

    RELEASED FOR PRODUCTION COMMUNICATING WITH THE GRINDER (Continued) To Change Language PRESS AND HOLD RIGHT HIDDEN BUTTON TO ENTER THE SET-UP MENUS NAME HOPPER? ENTER PASSWORD SET PASSWORD UNITS METRIC DONE ENG SET LANGUAGE ? PRESSING "NO" SCROLLS TO ENGLISH "REVIEW RECIPES?"...

  • Page 11: Dir Num: 36529.0001

    RELEASED FOR PRODUCTION COMMUNICATING WITH THE GRINDER (Continued) To Review Or Change Grind Time PRESS AND HOLD RIGHT HIDDEN BUTTON TO ENTER THE SET-UP MENUS NAME HOPPER? ENTER PASSWORD SET PASSWORD UNITS METRIC DONE ENG GRIND TIME "#.#" SET LANGUAGE ? DONE PRESSING "YES"...

  • Page 12: Dir Num: 36529.0001

    RELEASED FOR PRODUCTION COMMUNICATING WITH THE GRINDER (Continued) To Restore Factory Defaults Or Test Outputs and Switches PRESS AND HOLD RIGHT HIDDEN BUTTON TO ENTER THE SET-UP MENUS NAME HOPPER? ENTER PASSWORD SET PASSWORD TEST OUTPUTS? UNITS METRIC DONE ENG LEFT GATE NEXT SET LANGUAGE ?

  • Page 13: Dir Num: 36529.0001

    RELEASED FOR PRODUCTION COMMUNICATING WITH THE GRINDER (Continued) Resetting The Grinder Memory (To Match Chart Below) 1. Unplug grinder from the outlet. 2. Press in and hold both the STOP and GRIND buttons and plug cordset into the outlet. After a short pause, the display will show four rows of dashes.

  • Page 14: Dir Num: 36529.0001

    RELEASED FOR PRODUCTION COMMUNICATING WITH THE GRINDER (Continued) Entering A Coffee Name Using A Recipe Card Press the STOP button and place the chip portion of the card under the sensor coil on the front of the grinder. The LCD display will enter the RECIPE CARD menu. CARD CONTAINS RECIPE FOR THE COFFEE NAME CAN BE...

Table of Contents