Sony HXCU-100 Operating Instructions Manual page 16

System status
* S y s t e m S t a t u s *
H X C - 1 0 0 1 0 8 0/ 5 9 . 9 4 I
R e f e r e n c e : F r e e L o c k
S D I - 1 / 2 : 1 0 8 0 /5 9 . 9 4 I
S D I - 3 / 4 : 5 2 5 / 59 . 9 4 I
C o m p o n e n t : S D Y CD
R e t u r n 1 : 1 0 8 0 /5 9 . 9 4 I
R e t u r n 2 : 5 2 5 / 59 . 9 4 I
R e t u r n 3 : N T S C
R e t u r n 4 : N T S C
The camera model name and signal format are displayed at
the top of the page (a "-" mark is displayed instead when a
camera is not connected).
Reference: Reference signal format and lock status
SDI-1/2: SDI OUTPUT 1/2 connector output format setting
SDI-3/4: SDI OUTPUT 3/4 connector output format setting
Component: Component signal connector output format
setting
Return1: Return 1 return signal format setting
Return2: Return 2 return signal format setting
Return3: Return 3 return signal format setting
Return4: Return 4 return signal format setting
CCU hardware diagnostics
* D i a g n o s i s *
D P R : O K S DI
S Y : O K V IF
F r o n t P a n e l : O K
The camera Auto Setup category, and the corresponding
setup item and status are displayed at the top of the page.
DPR: DPR board status
SDI: SDI board status
SY: SY board status
VIF: VIF board status
Front Panel: HKCU-FP1 CCU Control Panel status (displayed
only when the HKCU-FP1 CCU Control Panel is fitted)
Camera system diagnostics
Page 1
* S y s t e m D i a g 1 /3 *
T R I A X T y p e D ig i t a l
C a b l e C on n e c t
C o m p . A ut o
S t e p 4
F a n P o w e r O K
T i m e r 9 6 H
C C U P o w e r A C OK
S e r i a l N o 1 0 00 0 1
TRIAX Type: Triax transmission mode
TRIAX Cable: CCU triax cable connection status
TRIAX Comp.: Triax cable compensation mode selection
16
Status Display
1 / 12
2 / 12
: O K
: O K
3 / 12
TRIAX Step: Triax cable compensation step (internal circuit
step display)
Fan Power: CCU power supply fan status
Timer: Elapsed time since power-on
CCU Power: CCU power supply type and status
SerialNo: CCU serial number
Page 2
*Sy ste m D ia g 2 /3*
C AME RA C abl e C on nec t
D ata O K
P owe r O K
T one D et ect
R EMO TE C abl e C on nec t
D ata O K
P owe r O K
CAMERA Cable: Camera cable connection status
CAMERA Data: Camera data transmission status
CAMERA Power: Camera power supply status
CAMERA Tone: Camera identification tone detection status
REMOTE Cable: Remote device cable connection status
REMOTE Data: Remote device data transmission status
REMOTE Power: Remote device power supply status
Page 3
*Sy ste m D ia g 3 /3*
In ter com
CCU Pri va te
CAM ERA C H1 ENG
MIC O FF
C H2 ENG
MIC O FF
CA M M IC Ga in Loc al
C H1 60dB
C H2 60dB
Intercom CCU: CCU intercom selection
Intercom CAMERA CH1: Camera intercom channel 1
selection and microphone status
Intercom CAMERA CH2: Camera intercom channel 2
selection and microphone status
CAM MIC Gain: Camera microphone circuit control selection
CAM MIC CH1: Camera microphone channel 1 amplifier gain
CAM MIC CH2: Camera microphone channel 2 amplifier gain
Network diagnostics
Page 1
*Ne two rk Di ag 1/3 *
Mac Add res s: 000 000 -0 000 00
Aut o N ego ti ati on: O N
Aut o M DI/ MD IX : O N
Con nec tio n Spe ed: 10 0M
Dup lex Mo de : HA LF
MDI /MD IX : MD IX
Lin k S tat us : OK
MacAddress: MAC address stored in CCU EEPROM
Auto Negotiation: Auto negotiation setting
Auto MDI/MDIX: Auto-MDIX setting
4/ 12
5/ 12
6/ 12