Sony CDP-CX333ES Service Manual page 14

LOADING AGING MODE
• This mode is used for repeating loading operations continuously.
• Aging will be performed continuously unless an error occurs.
• When an error occurs, the error code will be displayed on the
fluorescent indicator tube.
Procedure:
1. Set a disc in the DISC 1 slit.
2. With the power ON, while pressing the
[ OPEN/CLOSE]
and button, press the
§
3. When the mode is set, both the
start to blink.
[ ]
·
4. When the button is pressed, only the
blink and aging starts.
5. To release the mode, press the
The error codes displayed during operations and when errors oc-
cur are the same as the "AGING MODE" described earlier.
TABLE AGING MODE
• This mode is used for rotating the table randomly.
• Aging will be performed continuously unless an error occurs.
• When an error occurs, the error code will be displayed on the
fluorescent indicator tube.
Procedure:
1. Set discs in slits 1, 2, 99, 100, and 200.
2. With the power ON, while pressing the
[ OPEN/CLOSE]
and button, press the
§
3. When the mode is set, both the
start to blink.
[ ]
·
4. When the button is pressed, only the
blink and aging starts.
5. To release the mode, press the
During aging, operations will be carried out sequentially in the
order of No. 1, No. 2, No. 100, No. 99, and No. 200 slits.
The error codes displayed during operations and when errors oc-
cur are the same as the "AGING MODE" described earlier.
DOOR POP UP AGING MODE
• This mode is used for performing aging of the CD pop up part
and door open/close.
It is used for checking if operations are performed normally.
Procedure:
1. To select a slot to be aged, press the
[DISC/CHARACTER]
and rotate the
opened to select a number.
2. With the power ON, while pressing the
[ OPEN/CLOSE]
and
§
[ ]
·
3. When the button is pressed, aging starts, and door open/
close and up/down operations of the pop up part are performed
continuously.
4. To release the mode, press the
The number of times aging is performed will be displayed on the
fluorescent indicator tube during operations.
14
[GROUP 2]
[+100]
button.
[ ] [ ]
· P
and indicators will
[ ]
·
indicator will
[ ]
1/
u button.
[GROUP 3]
[+100]
button.
[ ] [ ]
· P
and indicators will
[ ]
·
indicator will
[ ]
1/
button.
u
[ OPEN/CLOSE]
§
knob with the front door
[GROUP 4]
[+100]
button, press the button.
[ ]
1/
button.
u
TABLE ROTATION MODE
• This mode is used for electrical adjustments. Refer to the sec-
tion on Electrical Adjustments.
TITLE MEMO SHIFT MODE
• This mode is used for writing title memo information recorded
in this unit in a different unit.
Use it for transferring disc memo contents written by the cus-
button tomer to the new units when replacing the unit, etc.
Connection:
This unit
(Copy source)
COMMAND MODE: CD3
CONTROL A1 II
Procedure:
1. Connect two units using the
shown in the figure.
[COMMAND MODE]
button 2. Set the
[CD3]
to and the
tination unit to
3. With the power on, while pressing the
[ OPEN/CLOSE]
§
[+100]
the button.
4. When the data has been transferred, the fluorescent indicator
tube displays "complete" for about 1 second.
MODEL NAME DISPLAY
• Model names can be displayed on the fluorescent indicator tube
for checking the microprocessor model setting, etc.
Procedure:
With the power ON, while pressing the
buttons, press the
The model name is displayed on the fluorescent indicator tube.
MICROPROCESSOR VERSION DISPLAY
• The microprocessor version can be displayed on the fluorescent
button indicator tube.
Procedure:
button With the power ON, while pressing the
buttons, press the
The microprocessor version is displayed on the fluorescent indi-
cator tube.
ALL LIT MODE
• This mode is used for lighting the whole fluorescent indicator
tubes and LEDs.
Procedure:
With the power ON, while pressing the
buttons, press the
Both the fluorescent indicator tubes and LEDs will light up com-
pletely.
To release this mode, press the
Flow of data
Another unit
(Copy destination)
COMMAND MODE: CD1
CONTROL A1 II connection cord
provided
[CONTROL A1 II]
switch of the copy source unit
[COMMAND MODE]
switch of the copy des-
[CD1]
.
[GROUP 7]
button of the copy destination unit, press
[GROUP 1]
[+100]
button.
[GROUP 2]
[+100]
button.
[GROUP 3]
[+100]
button.
[ ]
1/
mode.
u
connection cord
button and
[ ]
·
and
[ ]
and ·
[ ]
·
and