Table of Contents

Advertisement

SERVICE MANUAL
Ver 1.0 2002. 02
Compact disc player
Laser
Semiconductor laser (λ = 780 nm)
Emission duration: continuous
Max 44.6 µW*
Laser output
* This output is the value measured at
20 Hz to 20 kHz ±0.5 dB
Frequency response
Signal-to-noise ratio
More than 107 dB
Dynamic range
More than 86 dB
Harmonic distortion
Less than 0.009 %
Channel separation
More than 100 dB
Outputs
Jack
Maximum
type
output
level
Phono
2 V
ANALOG OUT
jacks
(at 50 kilohms)
Optical
–18 dBm
DIGITAL OUT
output
(OPTICAL)
connector
Sony Corporation
9-873-551-01
2002B1600-1
Home Audio Company
© 2002.02
Published by Sony Engineering Corporation
SPECIFICATIONS
a distance of 200 mm from the
objective lens surface on the Optical
Pick-up block with 7 mm aperture.
Load impedance
Over 10 kilohms
Wave length: 660 nm
CDP-CX355
Model Name Using Similar Mechanism
CD Mechanism Type
Base Unit Type
Optical Pick-up Type
General
Where purchased
Power consumptions
USA and Canadian
120 V AC, 60 Hz
Australia
240 V AC, 50/60 Hz
Europe and Asia
230 V AC, 50/60 Hz
Other countries
120 V AC, 50/60 Hz
Dimensions (approx.)
430 189 493 mm
(17 ×
(w/h/d)
incl. projecting parts
Mass (approx.)
8.5 kg (18 lbs 12 oz)
Supplied accessories
• Audio cord (1)
• Remote commander (remote) (1)
• Size AA (R6) batteries (2)
Design and specifications are subject to change without notice.
COMPACT DISC PLAYER
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
NEW
CDM54-K1BD45
BU-K1BD45
KSS-213BFN
Power requirements
13 W
14 W
13 W
13 W
×
×
×
7
1
/
19
3
/
in.)
2
8

Advertisement

Table of Contents
loading

Summary of Contents for Sony CDP-CX355

  • Page 1 Over 10 kilohms Phono ANALOG OUT jacks (at 50 kilohms) Wave length: 660 nm Optical –18 dBm DIGITAL OUT output (OPTICAL) COMPACT DISC PLAYER connector Sony Corporation 9-873-551-01 2002B1600-1 Home Audio Company © 2002.02 Published by Sony Engineering Corporation...
  • Page 2 DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT 4-238-109-3π Singapore CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE 4-238-109-4π Australian REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY 4-238-109-5π DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
  • Page 3: Table Of Contents

    CDP-CX355 SECTION 1 SERVICING NOTE TABLE OF CONTENTS NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK 1. SERVICING NOTE ····················································· OR BASE UNIT 2. GENERAL ··································································· The laser diode in the optical pick-up block may suffer electrostatic 3. DISASSEMBLY ·························································· break-down because of the potential difference generated by the 3-1.
  • Page 4 CDP-CX355 CD-TEXT TEST DISC This unit is able to display the TEXT data (character information) written in the CD on its fluorescent indicator tube. The CD-TEXT TEST DISC (TGCS-313:J-2501-126-A) is used for checking the display. To check, perform the following procedure.
  • Page 5 CDP-CX355 Table 2: CD-TEXT TEST DISC Recorded Contents and Display (In this unit, some special characters cannot be displayed. This is no a fault.) TRACK Recorded contents Display N All the same ! ” # $ % & ´ (21h to 27h)1kHz 0dB L&R + , –...
  • Page 6: General

    CDP-CX355 SECTION 2 GENERAL 4 5 6 7 8 11 12 15 16 17 18 19 20 21 22 36 35 34 33 32 31 30 29 28 27 Location of Parts and Controls 1 1/u (power) button 21 NO DELAY button...
  • Page 7: Disassembly

    CDP-CX355 SECTION 3 DISASSEMBLY Note : Disassemble the unit in the order as shown below. • The parts surrounded by square are included in the solid line square in the area shown by the dotted line square CASE (Page 8) BRACKET (F.W.)
  • Page 8: Case

    CDP-CX355 3-1. Case 2 three screws (CASE 3 TP2) 1 two screws (CASE 3 TP2) 3 two screws (CASE 3 TP2) 5 case 4 two screws (CASE 3 TP2) 3-2. Bracket (F. W. ) 2 wire (flat type) (21 core)
  • Page 9: Front Panel Assy

    CDP-CX355 3-3. Front Panel Assy 9 remove the claw 3 connector (CN792) 4 screw (+BVTP 3 x 8) q; front panel assy 8 remove the claw 6 three screws (+BVTP 3 x 8) 7 two screws (+BVTP 3 x 8) 5 cover (chassis) 3-4.
  • Page 10: Led Board, Guide (Door. T)

    CDP-CX355 3-5. LED Board, Guide (Door. T) 3 screw (+BVTP 3 x 8) 8 window (internal illumination) 6 LED board 1 screw (+BVTP 3 x 16) 9 guide (door.T) Note during re-assembling When re-assembling, align the positions as shown. 3-6. Table (300) Assy, Cover (P.T.)
  • Page 11: Motor Board, Door Motor Assy (M83)

    CDP-CX355 3-7. D. MOTOR Board, Door Motor Assy (M83) 1 remove two soldrings. 2 D. motor board 4 belt 5 door motor assy (M83) 3 two screws (+B 2.6 x 3)
  • Page 12: Sw Board

    CDP-CX355 3-8. D. SW Board 7 holder (L-SW) 1 washer 6 two claws 2 gear (door.cam) 5 two screws (+BTP 2.6 x 6) 8 D. SW board 3 washer 4 gear (door.drive) Precaution during the gear (door.cam) installation Install the gear (door.cam) in the direction shown in the illustration and rotate it fully Move the slider (pop-up) and the lever (cam.pu) fully...
  • Page 13: Base (Door, Gear) Assy

    CDP-CX355 3-9. Base (Door. Gear) Assy 4 base (door.gear) assy Note during re-assembling 1 connector (CN508) When re-assembling, align the positions as shown. 3 two screws (+BVTP 3 x 8) three screws (+BVTP 3 x 8) 3-10. Pop-up Assy 1 step screw...
  • Page 14: Sens (Out) Board

    CDP-CX355 3-11. D. SENS (OUT) Board 2 screw (+BVTP 3 x 6) 4 D. SENS (OUT) board 1 connector (CN83) 3-12. T. SENS Board 2 four screws (+PTPWH 3 x 6) 5 T. SENS board connector (CN81) connector (CN82) connector (CN83)
  • Page 15: Sens (In) Board

    CDP-CX355 3-13. D. SENS (IN) Board 4 screw (+PTPWH 3 x 6) 5 D. SENS (IN) board 1 two screws (+PTPWH 3 x 6) 3 holder (table sensor) 2 two claws 3-14. Back Panel Section qa four screws (+BVTP 3 x 8)
  • Page 16: Main Board, Jack Board

    CDP-CX355 3-15. MAIN Board, JACK Board MAIN board two screws (+BVTP 3 x 8) two screws (+BVTP 3 x 8) 1 connector (CN510) 2 connector (CN511) three screws (+BVTP 3 x 8) 8 back panel JACK board 3-16. POWER Board...
  • Page 17: Bracket (Top) , Bu Assy

    CDP-CX355 3-17. Bracket (Top) , BU Assy 2 bracket (top) 1 four screws (+BVTP 3 x 8) Note during re-assembling 3 BU assy When re-assembling, align the positions as shown. 4 8 washer 3-18. BU Holder Assy 3 tension spring (F-1)
  • Page 18: Bd Board, Optical Device (Ksm-213 Bfn)

    CDP-CX355 3-19. BD Board, Optical Device (KSM-213 BFN) 9 optical device 7 two vibration 3 remove two (KSM-213BFN) proof rubbers solderings. (sled) 4 remove two solderings. (spindle) 8 two vibration proof rubbers 5 wire (flat type) (16 core) (CN102) 1 wire (flat type) (23 core)
  • Page 19: Sw (A) Board, L. Sw (B) Board

    CDP-CX355 3-20. L. SW (A) Board, L. SW (B) Board 1 belt 3 pulley (1) 5 screw (+BVTP 3 x 8) 4 rotate the gear (center) in the direction of the arrow A fully. 6 rotate the Gear (center) in the direction of the arrow B fully.
  • Page 20: Cdm Assy

    CDP-CX355 3-21. CDM Assy 4 CDM assy 1 five screws (+BVTP 3 x 8) 3 screw (+PSW 3 x 8) 2 four screws (+BVTP 3 x 8) 3-22. Motor Assy (Loading) (M82) , Motor Assy (Table) (M81) , L. T. MOTOR Board...
  • Page 21: Service Mode

    CDP-CX355 SECTION 4 SERVICE MODE SPECIAL FUNCTION This unit is provided with several service modes. Details are shown in the following table. Mode name Power supply state Button operation Remarks ALL ERASE CLEAR + Note 1 AGING MODE GROUP 1 + OPEN/CLOSE + +100 §...
  • Page 22 CDP-CX355 Special Aging Mode Functions Aging Procedure Turn ON the power of the unit. Press the § OPEN/CLOSE The aging mode is provided with the following convenient functions • Disc setting mode (*1) and open the front cover. • Selection of presence of protection function during error (*2) Change the COMMAND MODE switch (S902) on set to CD1 .
  • Page 23 CDP-CX355 LOADING AGING MODE TABLE ROTATION MODE • This mode is used for repeating loading operations continuously. • This mode is used for electrical adjustments. Refer to the section • Aging will be performed continuously unless an error occurs. on Electrical Adjustments.
  • Page 24 CDP-CX355 MECHANISM ADJUSTMENT MODE • This mode is used for mechanism adjustments. Refer to the sec- tion on Mechanism Adjustments. SHIPMENT MODE • This mode is used for setting the unit to the shipment state. Do not execute it without a proper reason as it erases the memory of the title memo recorded by the customer.
  • Page 25: Test Mode

    CDP-CX355 SECTION 5 TEST MODE 5-1. ADJ Mode 5-2. Key and Display Check Mode Turn ON the power of the unit, set disc to disc table, and perform To set this mode, connect the test point (AFADJ) on the MAIN chucking.
  • Page 26: Adjustments

    CDP-CX355 SECTION 6 ADJUSTMENTS 6-1. Mechanical Adjustments Pop Up Mechanism Adjustment With the power ON, while pressing the GROUP 4 and · buttons, press the +100 button to enter the mechanism adjustment mode. Press the GROUP 1 button to operate the loading mechanism, and continue pressing until the disc table locks.
  • Page 27 CDP-CX355 Sensor Adjustment With the power ON, while pressing the GROUP 4 and · GROUP1 buttons, press the +100 button to enter the mechanism PAUSE button adjustment mode. GROUP4 Press the GROUP 1 button to operate the loading mechanism, PLAY button and continue pressing until the disc table locks.
  • Page 28: Electrical Adjustment

    CDP-CX355 6-2. Electrical Adjustment Note: A clear RF signal waveform means that the shape “◊” can be clearly distinguished at the center of the waveform. Note: RF signal waveform CD Block is basically designed to operate without adjustment. Therefore, check each item in order given.
  • Page 29 CDP-CX355 Rotate the DISC/CHARACTER knob in the counterclockwise Disc Sensor Adjustment direction and the disc table starts to rotate in the same direction. Be sure to perform this adjustment after sensor adjustment in Check that the waveform at this time is the same as that in step MECHANICAL ADJUSTMENT.
  • Page 30 CDP-CX355 Adjustment Location : [ BD BOARD ] – Conductor Side – IC101 TP (VC) TP (FE1) TP (TE1) IC131 (RFAC) [ MAIN BOARD ] – Component Side – – Conductor Side – CN506 RV501 DISC SENSOR ADJUSTMENT TP (AFADJ)
  • Page 31: Diagrams

    CDP-CX355 SECTION 7 DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING • Waveform • Circuit Board Location BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this necessary note is printed in IC101 yj XTAO each block.) LED board For schematic diagrams.
  • Page 32: Block Diagrams - Bd Section

    CDP-CX355 7-1. Block Diagrams – BD Section – IC101 DIGITAL SIGNAL PROCESSOR OPTICAL PICK-UP IC131 BLOCK (KSM-213BFN) RF AMP LASER DIODE POWER IC901 APC LD DIGITAL DOUT DIGITAL Q131 OPTICAL ASYO DRIVE RW/ROM DETECTOR RFAC RF EQ SUMMING RFDC RFDCO...
  • Page 33: Main Section

    CDP-CX355 – MAIN Section – J903 FL701 D940 D942 Q940 R-CH RECTIFIER –30V REG 2ND CD IN IC910 IC401 AVDD +5V REG Q324 D910-913 IC302(2/2) IC302(1/2) MUTE DVDD RECT –VCC MIX AMP BUFFER R-CH IC920 LOUT Q321 ANALOG OUT MUTE...
  • Page 34: Printed Wiring Board - Bd Section

    CDP-CX355 7-2. Printed Wiring Board – BD Section – • See page 31 for Circuit Boards Location. IC150 (VC) IC131 IC101 TP(FE1) TP(TE1) (RFAC) (Page 36) • Semiconductor Location Ref. No. Location IC101 IC131 IC150 Q131 Q132...
  • Page 35: Schematic Diagram - Bd Section

    CDP-CX355 7-3. Schematic Diagram – BD Section – • See page 31 for Waveforms. • See page 47, 48 for IC Block Diagrams. • See page 50 for IC Pin Function. IC B/D IC B/D RFSW...
  • Page 36: Printed Wiring Board - Main Section

    CDP-CX355 7-4. Printed Wiring Board – MAIN Section – • See page 31 for Circuit Boards Location. TO POWER BOARD CNP901 T. SENS BOARD KEYBOARD BOARD LED BOARD (Page 44) CN813 CN81 CNP203 (Page 39) (Page 46) (Page 46) DISP BOARD...
  • Page 37: Schematic Diagram - Main Section (1/2)

    CDP-CX355 7-5. Schematic Diagram – MAIN Section (1/2) – • See page 31 for Waveform. • See page 48 for IC Block Diagrams. • See page 52 for IC Pin Function. IC B/D...
  • Page 38: Schematic Diagram - Main Section (2/2)

    CDP-CX355 7-6. Schematic Diagram – MAIN Section (2/2) – • See page 49 for IC Block Diagrams. IC B/D IC B/D...
  • Page 39: Printed Wiring Board - T.sens Section

    CDP-CX355 7-7. Printed Wiring Board – T.SENS Section – 7-10. Schematic Diagram – SENSOR Section – • See page 31 for Circuit Boards Location. IC84 IC82 IC81 IC83 MAIN BOARD CN507 (Page 36) 7-8. Printed Wiring Board – D.SENS (IN) Section –...
  • Page 40: Printed Wiring Board - Display Section

    CDP-CX355 7-11. Printed Wiring Board – DISPLAY Section – • See page 31 for Circuit Boards Location. JOG BOARD CN705 MAIN BOARD (Page 42) CN502 (Page 36) IC703 • Semiconductor Location Ref. No. Location D701 D702 D703 D704 D705 D706...
  • Page 41: Schematic Diagram - Display Section

    CDP-CX355 7-12. Schematic Diagram – DISPLAY Section – • See page 49 for IC Block Diagrams. IC B/D...
  • Page 42: Printed Wiring Board - Jog Section

    CDP-CX355 7-13. Printed Wiring Board – JOG Section – • See page 31 for Circuit Boards Location. • Semiconductor Location DISP BOARD Ref. No. Location CN704 (Page 40) D771 D712 D713 D714 D715 D716 p/DISC EJECT...
  • Page 43: Schematic Diagram - Jog Section

    CDP-CX355 7-14. Schematic Diagram – JOG Section – /DISC EJECT...
  • Page 44: Printed Wiring Board - Power Section

    CDP-CX355 7-15. Printed Wiring Board – POWER Section – • See page 31 for Circuit Boards Location. 7-16. Schematic Diagram – POWER Section – MAIN BOARD CN902 (Page 36) TO MAIN BOARD CN901, 903 (Page 36) CNP901 • Semiconductor Location Ref.
  • Page 45: Printed Wiring Board - Jack Section

    CDP-CX355 7-17. Printed Wiring Board – JACK Section – • See page 31 for Circuit Boards Location. 7-18. Schematic Diagram – JACK Section – COMMAND MODE IC901 (Page 36) (Page 36)
  • Page 46: Printed Wiring Board - Switch/Motor Section

    CDP-CX355 7-19. Printed Wiring Board – SWITCH/MOTOR Section – 7-20. Schematic Diagram – SWITCH/MOTOR Section – • See page 31 for Circuit Boards Location. MAIN BOARD CN509 (Page 36) MAIN BOARD CN503 MAIN BOARD (Page 36) CN508 (Page 36) L.SW (A) BOARD...
  • Page 47: Ic Block Diagrams

    CDP-CX355 • IC Block Diagrams IC101 CXD2587Q (BD Section) ERROR DIGITAL CORRECTOR DIGITAL ASYMMETRY CORRECTION OPERATIONAL LRCK AMPLIFIER ANALOG SWITCH PCMD INTERFACE DEMODULATOR CONVERTER EMPH XVDD XTAI TIMING LOGIC CLOCK XTAO XTSL GENERATOR XVSS TES1 AVDD1 TEST AOUT1 SERVO DSP...
  • Page 48 CDP-CX355 IC131 CXA2581N-T4 (BD Section) RW/ROM DC OFST RFDCI – – RFDCO – RW/ROM VOFST APC AMP EQ ON/OFF RFAC EQ IN RW/ROM RFAC AC SUM SUMMING VOFST – – RW/ROM TE BAL RW/ROM – APC-OFF RW/ROM (Hi-Z) RW/ROM RW/ROM...
  • Page 49 CDP-CX355 IC931 LA5601 (MAIN Section) IC505 LA6510 (MIAN Section) – – V REF 1 2 3 4 5 6 7 8 9 10 VOMUTE RESET ON/OFF IC702 M66310FP (DISPLAY Section)
  • Page 50: Ic Pin Functions

    CDP-CX355 7-21. IC Pin Functions • IC101 DIGITAL SIGNAL PROCESSOR (CXD2587Q) (BD Section) Pin No. Pin Name Description SQSO Sub-Q 80-bit and PCM peak level data output (CD text data output) SQCK Clock input for SQSO read-out XRST System reset “L” : reset SYSM Muting input “H”...
  • Page 51 CDP-CX355 Pin No. Pin Name Description ASYO EFM full swing output ASYI Asymmetry comparate voltage input BIAS Asymmetry circuit constant current input RFAC EFM signal input AVSS3 — Analog ground CLTV Control voltage input for master VCO1 Filter output for master PLL...
  • Page 52 CDP-CX355 • IC501 SYSTEM CONTROL (MN101C49GSA) (MAIN Section) Pin No. Pin Name Description — Ground DOOR SW Door panel SW (5V: OPEN) Digital filter (not used) KEY1 KEY2 Key A/D input KEY3 KEY4 KEY5 D.SENS Disc sensor input VREF —...
  • Page 53 CDP-CX355 Pin No. Pin Name Description SELECT CX691 select port (H: CX691 L: Other) Table sensor input SELECT J select port (H: J L: Other) SELECT ES select port (H: ES L: HiFi) SELECT 2WAY select port (H: 2WAY L: 1WAY)
  • Page 54: Exploded Views

    CDP-CX355 SECTION 8 EXPLODED VIEWS NOTE: • The mechanical parts with no reference number • -XX, -X mean standardized parts, so they may in the exploded views are not supplied. The components identified by mark 0 or have some differences from the original one.
  • Page 55: Chassis Section 1

    CDP-CX355 8-2. Chassis Section 1 not supplied not supplied mechanism section 1 (CDM54-K1BD45) (pop-up assy) mechanism section 1 (CDM54-K1BD45) (base (door.gear) assy) chassis section 2 not supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-703-249-01 SCREW, S TIGHT, +PTTWH 3X6 4-216-091-01 HOLDER (TABLE SENSOR) 1-672-641-11 D.SENS(OUT) BOARD...
  • Page 56: Chassis Section 2

    CDP-CX355 8-3. Chassis Section 2 mechanism section 2 (CDM54-K1BD45) back panel section T902 T901 not supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 0 T901 1-433-668-11 TRANSFORMER, POWER (SUB) (AEP, UK, SP) 4-216-092-01 HOLDER (ROLLER)
  • Page 57: Back Panel Section

    CDP-CX355 8-4. Back Panel Section not supplied CNP901 not supplied not supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks A-4727-794-A MAIN BOARD, COMPLETE 4-238-109-42 PANEL, BACK (AUS) 1-790-420-11 WIRE (FLAT TYPE) (21 CORE) 4-238-109-51 PANEL, BACK (E)”...
  • Page 58: Front Panel Section

    1-672-632-12 KEYBOARD BOARD X-4954-417-1 PANEL ASSY, FRONT (US, CND) A-4727-728-A JOG BOARD, COMPLETE X-4954-470-1 PANEL ASSY, FRONT (AUS, UK, AEP, E, SP) A-4727-729-A DISP BOARD, COMPLETE 4-996-698-61 EMBLEM, SONY 4-985-553-21 CUSHION 4-977-358-01 CUSHION 4-951-620-01 SCREW (2.6X8), +BVTP 3-917-216-21 KNOB (TIMER)
  • Page 59: Mechanism Section 1 (Cdm54-K1Bd45) (Pop-Up Assy, Base (Door. Gear) Assy)

    CDP-CX355 8-6. Mechanism Section 1 (CDM54-K1BD45) (Pop-up Assy, Base (Door. Gear) Assy) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks X-4950-888-1 BRACKET (DOOR.GEAR) ASSY 4-216-100-01 HOLDER (POP-UP) 4-215-959-01 LEVER (CAM.PU) 4-216-098-01 LEVER (POP-UP) 4-215-955-01 GEAR (DOOR.PULLEY) 3-701-441-21 WASHER 4-215-956-01 GEAR (DOOR.CENTER)
  • Page 60: Mechanism Section 2 (Cdm54-K1Bd45)

    CDP-CX355 8-7. Mechanism Section 2 (CDM54-K1BD45) not supplied not supplied not supplied mechanism section 3 (CDM54-K1BD45) optical pick-up section (BU-K1BD45) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 4-216-081-01 SPRING (MG), TORSION X-4950-901-4 HOLDER ASSY, BU...
  • Page 61: Mechanism Section 3 (Cdm54-K1Bd45)

    CDP-CX355 8-8. Mechanism Section 3 (CDM54-K1BD45) mechanism section 4 (CDM54-K1BD45) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 4-216-070-01 LEVER (LOCK) X-4950-900-1 BRACKET (LEVER) ASSY 4-216-067-01 SPRING (CLAMP), COMPRESSION 4-216-080-01 SPRING (LIMITTER), TORSION 3-701-441-21 WASHER 4-216-079-01 LIMITTER (LEVER)
  • Page 62: Mechanism Section 4 (Cdm54-K1Bd45)

    CDP-CX355 8-9. Mechanism Section 4 (CDM54-K1BD45) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 4-216-058-01 GEAR (CENTER) 1-672-636-11 L.T.MOTOR BOARD 4-216-059-01 GEAR (TABLE) 4-216-054-01 BASE (CDM) 4-216-063-02 SLIDER 4-951-620-01 SCREW (2.6X8), +BVTP 4-216-062-01 LEVER (FULCRUM) A-4672-675-A MOTOR ASSY (TABLE) 1-672-643-11 L.SW(B) BOARD...
  • Page 63: Optical Pick-Up Section (Bu-K1Bd45)

    CDP-CX355 8-10. Optical Pick-up Section (BU-K1BD45) Ref. No. Part No. Description Remarks 1-792-024-11 WIRE (FLAT TYPE) (16 CORE) A-4727-737-A BD BOARD, COMPLETE * 453 4-992-054-01 RUBBER, VIBRATION PROOF 0 454 A-3328-818-A OPTICAL PICK-UP KSM-213BFN/C2NP 7-621-772-21 SCREW +B 2X5 The components identified by Les composants identifiés par...
  • Page 64: Electrical Parts List

    CDP-CX355 SECTION 9 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • CAPACITORS: • Abbreviation parts list may be different from the parts uF: µF CND : Canadian model specified in the diagrams or the components •...
  • Page 65 CDP-CX355 D. MOTOR D. SENS (IN) D. SENS (OUT) D. SW DISP Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R137 1-216-797-11 METAL CHIP 1/16W 1-672-634-11 D.SW BOARD R138 1-216-797-11 METAL CHIP 1/16W *********** R139 1-216-849-11 METAL CHIP...
  • Page 66 CDP-CX355 DISP JACK Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < RESISTOR > 1-672-629-12 JACK BOARD *********** R701 1-249-441-11 CARBON 100K 1/4W R702 1-247-807-31 CARBON 1/4W < CAPACITOR > R703 1-247-807-31 CARBON 1/4W R704 1-247-807-31 CARBON...
  • Page 67 CDP-CX355 KEYBOARD L. SW (A) L. SW (B) L. T. MOTOR Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < RESISTOR > < CONNECTOR > R715 1-249-407-11 CARBON 1/4W F * CNP203 1-568-944-11 PIN, CONNECTOR 6P...
  • Page 68 CDP-CX355 MAIN Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < RESISTOR > C913 1-126-768-11 ELECT 2200uF 20.00% 16V C914 1-126-768-11 ELECT 2200uF 20.00% 16V R805 1-249-401-11 CARBON 1/4W F C915 1-126-933-11 ELECT 100uF 20.00% 16V...
  • Page 69 CDP-CX355 MAIN Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < TRANSISTOR > R328 1-249-441-11 CARBON 100K 1/4W R329 1-249-441-11 CARBON 100K 1/4W Q321 8-729-141-26 TRANSISTOR 2SC3622ATP-LK R401 1-249-433-11 CARBON 1/4W Q322 8-729-141-26 TRANSISTOR 2SC3622ATP-LK R402 1-249-419-11 CARBON 1.5K...
  • Page 70 CDP-CX355 MAIN POWER Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R545 1-249-382-11 CARBON 1/6W F < CONNECTOR > R546 1-249-393-11 CARBON 1/4W F R547 1-249-431-11 CARBON 1/4W * CN991 1-580-230-11 PIN, CONNECTOR (PC BOARD) 2P...
  • Page 71 CDP-CX355 T. SENS Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 1-672-639-11 T.SENS BOARD ACCESSORIES ************ ************ < CONNECTOR > 1-418-419-11 REMOTE COMMANDER (RM-DX300) 1-558-271-11 CORD, CONNECTION * CN81 1-506-486-11 PIN, CONNECTOR 7P 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (UK)
  • Page 72 CDP-CX355 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision...

Table of Contents