Turn-On Volume Level; Semi-Osd Settings; Full-Osd Time Out Adjustment - Harman Kardon DPR 2005 Owner's Manual

Advanced Features
Turn On Volume Level
As is the case with most audio/video receivers,
when the DPR is turned on, it will always return
to the volume setting in effect when the unit was
turned off. However, you may prefer to always
have the DPR turn on at a specific setting,
regardless of what was last in use when the unit
was turned off. To change the default condition
so that the same volume level is always used at
turn-on, you will need to make an adjustment in
the menu. To start the
ADVANCED SELECT
adjustment, press the OSD button L to bring
the (Figure 1) to the screen.
MASTER MENU
button E, until the on-screen
Press the
⁄
cursor is next to the
ADVANCED
the Set button F to enter the
ADVANCED
menu (Figure 12).
SELECT
At the
ADVANCED SELECT
›
certain that the on-screen cursor is next to the
line by pressing the
VOLUME DEFAULT
buttons E as needed. Next, press the
/
⁄ ¤
button E so that the word
is highlighted
O N
in the video display. Next, press the
E once so that the on-screen
›
to the line. To set the
DEFAULT VOL SET
‹
desired turn-on volume, press the
E or hold them pressed until the desired vol-
ume level is shown on the
DEFAULT VOL
line. Note that this setting may NOT be
SET
made with the regular volume controls.
NOTE: Since the setting for the turn-on volume
cannot be heard while the setting is being made,
you may wish to determine the setting before
making the adjustment. To do this, listen to any
source and adjust the volume to the desired level
using the regular volume controls dî. When
the desired volume level to be used at turn-on is
reached, make a note of the setting as it appears
in the lower third of the video screen or in the
Main Information Display ˜.
A typical volume level will appear as a negative
number such as -25dB. When making the
buttons E to enter
adjustment, use the ‹ ›
/
this setting.
Unlike some of the other adjustments in this
menu, the turn-on volume default will remain in
effect even when the unit is turned off comple-
tely, unless it is changed or turned off in this
menu.
If you wish to make other adjustments in the
Buttons E until the on-
menu, press the
/
⁄ ¤
screen › cursor is next to the desired setting or
the
BACK T O MASTER MENU
press the Set button F. If you have no other
adjustments to make, press the OSD Button L
to exit the menu system.

Semi-OSD Settings

The semi-OSD system places one line messages
at the lower third of the video display screen
whenever the Volume, Input Source, Surround
mode or tuner frequency of any of the configura-
tion settings are changed. The semi-OSD system
is helpful in that enables you to have feedback
on any control changes or remote commands
using the video display when it is difficult to view
the front-panel displays. However, you may occa-
sionally prefer to turn these displays off for a par-
ticular listening session. You may also want to
adjust the length of time the displays remain on
› the screen. Both of those options are possible
line. Press with the DPR.
To turn off the semi-OSD system, you will need to
make an adjustment in the
menu (Figure 12). To start the adjust-
menu make SELECT
ment, press the OSD button L to bring the
MASTER MENU
Button E, until the on-screen
›
to the
ADVANCED
F to enter the
button
¤
menu.
cursor is next
At the
ADVANCED SELECT
›
buttons
/
certain that the on-screen
line by pressing the
SEMI OSD
E as needed. Next, press the
that the word
OFF
display.
Note that this setting is temporary and will
remain active only until it is changed or until the
DPR is turned off. Once the unit is turned off, the
semi-OSD displays will remain activated, even if
they were switched off for the previous listening
session.
To change the length of time that the semi-OSD
displays remain on the screen, go to the
ADVANCED SELECT
earlier, and press the
ed, until the on-screen
SEMI-OSD TIME OUT
Buttons E until the desired time in
the ‹ ›
/
seconds is displayed. Note that unlike most of the
other options in this menu, this is a permanent
setting change, and the time-out entry will
remain in effect until it is changed, even when
the unit is turned off.
If you wish to make other adjustments in the
menu, press the
›
screen cursor is next to the desired setting or
the
BACK T O MASTER MENU
press the Set button F. If you have no other
line and
adjustments to make, press the OSD Button L
to exit the menu system.
ADVANCED
to the screen. Press the
⁄
cursor is next
›
line. Press the Set Button
ADVANCED SELECT
menu make
cursor is next to the
›
buttons
/
⁄ ¤
button E so
›
is highlighted in the video
Menu as outlined
buttons E as need-
/
⁄ ¤
› cursor is next to the
line. Next, press
Buttons E until the on-
/
⁄ ¤
line and

Full-OSD Time Out Adjustment

The menu system is used to
FULL OSD
simplify the setup and adjustment of the DPR
using a series of on-screen menus. The factory
default setting for these menus leaves them on
the screen for 20 seconds after a period of inac-
tivity before they disappear from the screen or
Time Out. This Time Out is a safety measure to
prevent the menu text from burning into the CRTs
in your monitor or projector, which might happen
if they were left on indefinitely. However, some
viewers may prefer a slightly longer or shorter
period before the Time Out display.
To change the Full-OSD Time Out, you will need
to make an adjustment in the
ADVANCED
menu (Figure 12). To start the adjust-
SELECT
ment, press the OSD button L to bring the
to the screen. Press the
MASTER MENU
button E, until the on-screen
¤
to the line. Press the Set Button
ADVANCED
F to enter the
ADVANCED SELECT
menu (Figure 12).
At the
ADVANCED SELECT
certain that the on-screen cursor is next to the
›
line by pressing the
FULL OSD TIME OUT
Buttons E as needed. Next, press the
/
⁄ ¤
buttons E until the desired time is dis-
‹ ›
/
played in seconds. Note that unlike most of the
other options in this menu, this is a permanent
setting change, and the time-out entry will
remain in effect until it is changed, even when
the unit is turned off.
If you wish to make other adjustments in the
Buttons E until the
menu, press the
/
⁄ ¤
on-screen › cursor is next to the desired setting
or the
BACK T O MASTER MENU
press the Set button F. If you have no other
adjustments to make, press the OSD Button L
to exit the menu system.
ADVANCED FEATURES 41
⁄
cursor is next
menu make
line and