Barco VS05 Owner's Manual
  1. Manuals
  2. Brands
  3. Barco Manuals
  4. Projector
  5. VS05
  6. Owner's manual
Barco VS05 Owner's Manual

Barco VS05 Owner's Manual

Projection systems
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
BARCO PROJECTION SYSTEMS
VS05
R9827891
OWNER'S MANUAL
Date: 13.10.99
Art. No: R5976061

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VS05 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Barco VS05

Summary of Contents for Barco VS05

  • Page 1 BARCO PROJECTION SYSTEMS VS05 R9827891 OWNER'S MANUAL Date: 13.10.99 Art. No: R5976061...
  • Page 2 Due to constant research, the information in this manual is subject to change without notice. Produced by BARCO NV, 1999 All rights reserved. Trademarks are the rights of their respective owners. Printed in Belgium...

  • Page 3: Table Of Contents

    ..D.1. Sources to VS05 ................10 ..D.2 Source to projector ................ 11 III. Operating instructions ................12 A. With the button panel on the VS05............12 ..A.1. Input selection ................12 ..A.2. Adaptation Keypad to PPM/RC5 Coding ........12 ..

  • Page 4: Safety Instructions

    All instructions for operating and use of this equipment must be followed precisely. On installation Do not place this VS05 on unstable cart, stand or table. The VS05 may fall, causing serious damage to it. Do not use this VS05 near water.

  • Page 5: Introduction

    INTRODUCTION General The VS05 is a versatile Video and HDTV source selector for all Barco's digitally controlled large screen projectors. It offers the possibility to connect and switch up to 5 Composite Video sources and 3 Super Video sources and 1 RGB analog source.

  • Page 6: Installation Of The Vs05

    A. Projector - VS05 connections. Power down the projector before starting the connections. A.1. Data communication connection. Use a D9-D9 link cable to connect the VS05 to the projector. The cables are available in the following lengths : 5 m (15ft)
  • Page 7 VS05 Connection VS05 - BARCO 800, 1100, 1200 or 1600 series projector. PORT 4/5 PO RT 1 PROJECTOR M ODE POWER/M AINS (RGB - HV) (VIDEO) GREEN : operational Comp/H sync V syn c RED : stand-by...

  • Page 8: Signal Connection

    VS05 A.2. Signal connection Connect the video output of the VS05 to the video input of projector using coaxial cable with BNC connectors. Connect the S-Video output of the VS05 to the S-Video input of the projector using a 4-wire coaxial cable with 4 pin connectors.
  • Page 9 VS05 Signal interconnection VS05 - BARCO 800, 1100, 1200 and 1600 series projector. PORT 4/5 PORT 1 PRO JECTO R MODE PO WER/MAINS (RGB - HV) (VIDEO) G REEN : ope rational Comp/H sync V sync RED : stand-by...

  • Page 10: Vs05 - Audio Amplifier Connection

    VS05 B. VS05 - audio amplifier connection. Connect the left and right audio outputs of the VS05 to the left and right audio inputs of an audio amplifier using two conductor audio cables with RCA (cinch) connectors.

  • Page 11: Source Connections

    D.1. Sources to VS05 D.1.a. Video + audio Connect the video sources to the video inputs of the VS05 (inputs 1 to 5) using coaxial cables with BNC connectors. Connect the audio sources, corresponding with the Video sources, to the audio inputs of the VS05 using two conductor audio cables with RCA (cinch) connectors.

  • Page 12: Source To Projector

    (for projectors with component video input) or to the Component inputs (5000 series) using coaxial cables with BNC connectors. Connect the corresponding audio signals to audio input 9 of the VS05 using two conductor audio cables with RCA (cinch) connectors.

  • Page 13: Operating Instructions

    VS05. The controls on the button panel of the VS05 have the same functions as those on the RCU:...

  • Page 14: Analog Picture Settings : 'Brightness', 'Color', 'Contrast', 'Tint' And . ..... 'Sharpness

    Note for source selection 9 : Set the switches on the front panel of the VS05 in their correct position before selecting source 9. The following indications have to be set before a correct operation is possible. INPUT SELECTIO N 9...

  • Page 15: Pause

    B. With the RCU of the projector. With the RCU, it is possible to control the projector and the VS05. Point the IR beam to the reflective screen surface or to one of the IR inputs of the projector.

  • Page 16: Analog Picture Settings : 'Brightness', 'Color', 'Contrast', 'Tint' And . ..... 'Sharpness

    1100, 1200, 1600,5000 series) or to the Component input (5000 series) (see Source to VS05 connection). Note for source selection 9 : Set the switches on the front panel of the VS05 in their correct position before selecting source 9.

  • Page 17: Stand-By

    EXIT a change of an image control. When text is off, no indication will be displayed on the ENTER screen when changing an image control. ADDR ê STBY PAUSE TEXT FREEZ R59 76061 VS05 131099...

  • Page 18: Stand Alone Use Of The Vs05

    5 video inputs and 3 S-Video inputs can be switched through to the outputs of the VS05. The selection has to be done with the numeric keys on the button panel of the VS05 (source 1 to 8, no source 9 -direct connection to the projector - available).
  • Page 19 BARCO nv/Projection Systems Noordlaan 5 B-8520 Kuurne Belgium Printed in Belgium...

Table of Contents