Siemens REV17 Series Operating Instructions

Operating instructions
REV17.. - 7-day room temperature controller with weekday/weekend selection for the right temperature at the right time. All factory
settings already provide optimal living comfort. You can easily adjust the controller to your needs with the user-assisted clear-text display
and program selection slider.
Note the following for placing the room unit:
• Make sure no other influencing factors influence the room unit's temperature sensor (no solar radiation and other heat or cold source influences).
Day of week Radio clock
active
Replace battery
Info mode
Installer mode
Temperature
setpoint symbols
Text display
Alarm
Heating mode
Switching pattern
with time cursor
Operating mode
selector:
- Automatic
- Exception day
- Comfort mode
- Energy saving
mode
- Frost
protection
mode
1 2 3 4 5 6 7 8
If the selected operating mode does not support the setting, the time display shows PASS.
Special symbols displayed
The controller display can show the following special symbols:
Is symbol displayed ?
The alarm indicates an error!
Press the Info button and check the error message (e.g. radio clock signal, radio connection to receiver, etc.). Contact a specialist as needed.
Is symbol displayed ?
This symbol tells you that you must exchange the batteries within the next 3 months.
Insert 2 new alkaline batteries type AA, 1.5 V as follows:
Remove the controller from the mounting base; open the battery compartment on the rear; remove the old batteries; insert the new batteries and
reinsert the controller in the base.
Caution: Time and date are retained for max. 1 minute.
(All other settings are fixed and remain unchanged!)
Dispose of the batteries as per regulations
B2203en
REV17..
Date Setting: 1-5, 6-7 Time display
Reading: 1..7
Remote control active
Holiday mode
Automatic mode
Party mode active
Exception day mode
Continuous comfort mode
°C or °F
Continuous energy
saving mode
Heating On
Frost protection mode
Temperature display
Info button
Increase values, set time or
make a selection
Change between Comfort and
energy saving temperature
(active until next switching time)
and Party function
Decrease values, set time or
make a selection
Program selection slider
RUN
9 10 11 12 13 14 15 16 17 18
Is symbol displayed ?
The radio clock symbol only appears if the receiver is set up and activated to receive the time signal from Frankfurt (Germany). A
permanent symbol indicates that both time and date of the controller are synchronized to Frankfurt radio clock (DCF77).
The symbol flashes if the signal is not received for more than 1 week.
Is symbol displayed ?
The controller is in heating mode .
Commission the controller and quick start
The controller contains a factory-set heating switching pattern and temperature values.
Proceed as follows for initial commissioning:
Remove the controller from the mounting base and pull off the black insulating tape from the 2 batteries: The controller turns
on automatically. Reinsert the controller in the mounting base.
After startup, a welcome message appears for ca. 2 minutes. Press a button to interrupt the message. Language selection
starts with "ENGLISH" (factory setting). Press
accept your language.
Slider in position 1 (time setting): Press
Note: You do not need to enter the time when DCF77 receiver for the
time signal from Frankfurt (Germany) is equipped.
Slider in position 2 (date: day/month/year): Press
Note: You do not need to enter the date when DCF77 receiver for the
time signal from Frankfurt (Germany) is equipped.
Move the slider to the very right to position RUN (only way to close the cover).
RUN
Set the operating mode with the operating mode selector.
Factory setting is .
Fold the operating instructions and reinsert in the mounting base.
Turn on display lighting, check error messages or other important information
Press the Info button once to activate display backlighting. Backlighting goes off automatically after a short time.
Continuing to press the Info button activates the information display:
is lit. The device first shows pending error messages and then important information (e.g. switching programs, ...).
Change the temperature level in the time switch program,
or are you not at home for a while?
In the time switch program, press this button to change from the current temperature level to the next and back.
Quickly activate energy saving temperature when you leave the apartment briefly to save energy.
The change appears on the display. It is valid only until the next switching time.
Tips to save energy without reducing comfort
•
Heat your rooms to max 21 °C.
•
Use to switch to energy saving temperature even if you are absent only briefly.
•
Air out your rooms briefly, but with wide-open windows.
24.12.2007
or until your language appears. Press or move the slider to
or to set the time.
or to set the date.
Siemens, Building Technologies