Page 1 Journey 2 0 1 6 O W N E R ’ S M A N U A L...
Page 2 This manual illustrates and describes the operation of VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name FCA features and equipment that are either standard or op- US LLC shall be deemed to be deleted and the name FCA tional on this vehicle.
Page 3: Introduction 3
TABLE OF CONTENTS SECTION PAGE INTRODUCTION ............. . . 3 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE .
Page 5: Table Of Contents
INTRODUCTION CONTENTS INTRODUCTION ......4 VEHICLE IDENTIFICATION NUMBER ..6 HOW TO USE THIS MANUAL ....4 VEHICLE MODIFICATIONS/ALTERATIONS .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained tech- Congratulations on selecting your new FCA US LLC nicians and genuine MOPAR® parts, and cares about vehicle. Be assured that it represents precision workman- your satisfaction.
Page 7 INTRODUCTION 5...
Page 8: Vehicle Identification Number
6 INTRODUCTION WARNINGS AND CAUTIONS The VIN is also stamped on either right or left hand side of the engine block. This Owner’s Manual contains WARNINGS against oper- ating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle.
Page 9: Vehicle Modifications/Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Stamped VIN Location NOTE: It is illegal to remove or alter the VIN.
Page 11 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A WORD ABOUT YOUR KEYS ... . .12 VEHICLE SECURITY ALARM — IF EQUIPPED ......18 ▫...
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Using The Panic Alarm ....23 ▫ Remote Start Comfort Systems — If Equipped ......29 ▫...
Page 13 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 OCCUPANT RESTRAINT SYSTEMS ..46 SAFETY TIPS ......107 ▫...
Page 14: A Word About Your Keys
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS NOTE: In case the ignition does not change with the push of a button, the RKE transmitter (Key Fob) may Your vehicle uses a keyless ignition system. This system have a low or dead battery.
Page 15: Key Fob
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the Key Fob go dead.
Page 16: Ignition Or Accessory On Message
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE you to cycle the ignition to OFF. In addition to the chime, the ignition or accessory on message will display in the cluster. NOTE: With the Uconnect system, the power window switches, radio, power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition is cycled to the OFF position.
Page 17: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 WARNING! (Continued) WARNING! (Continued) • Do not leave children or animals inside parked “OFF” mode, remove the Key Fob from the vehicle vehicles in hot weather. Interior heat build-up may and lock the vehicle. •...
Page 18: Sentry Key
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. This device may not cause harmful interference, and programmed to the vehicle can be used to start and operate the vehicle. The system will not allow the engine 2. This device must accept any interference received, to crank with an invalid Key Fob.
Page 19: Replacement Keys
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 CAUTION! CAUTION! • Do not make modifications or alterations to the • Always remove the Key Fobs from the vehicle and immobilizer system. Modifications or alterations to lock all doors when leaving the vehicle unat- the immobilization system may result in a loss of tended.
Page 20: Customer Key Programming
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Customer Key Programming VEHICLE SECURITY ALARM — IF EQUIPPED Programming Key Fobs or RKE transmitters may be The Vehicle Security Alarm monitors the vehicle doors performed at an authorized dealer. and liftgate for unauthorized entry and the Keyless Enter-N-Go Start/Stop button for unauthorized opera- General Information tion.
Page 21: To Arm The System
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 To Arm The System To Disarm The System Follow these steps to arm the Vehicle Security Alarm: The Vehicle Security Alarm can be disarmed using any of the following methods: 1. Make sure the vehicle ignition system is OFF (refer to •...
Page 22: Security System Manual Override
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with Keyless Enter-N-Go, If the Vehicle Security Alarm is armed and the battery insert a valid key into the ignition switch and turn becomes disconnected, the Vehicle Security Alarm will the key to the ON position.
Page 23: Illuminated Entry
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 • The Illuminated Entry system will not operate if the ILLUMINATED ENTRY dimmer control is in the “Dome defeat” position The courtesy lights will turn on when you use the (extreme bottom position). Remote Keyless Entry (RKE) transmitter to unlock the doors or open any door or liftgate.
Page 24: To Unlock The Doors And Liftgate
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the vehicle is equipped with Passive Entry, refer to “Keyless Enter-N-Go” in “Things To Know Before Start- ing Your Vehicle” for further information. 1st Press Of Key Fob Unlocks This feature lets you program the system to unlock either the driver’s door or all doors on the first push of the UNLOCK button on the RKE transmitter.
Page 25: To Lock The Doors And Liftgate
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Headlight Illumination On Approach Sound Horn With Lock This feature activates the headlights for up to 90 seconds This feature will cause the horn to chirp when the doors when the doors are unlocked with the RKE transmitter. are locked with the RKE transmitter.
Page 26: Programming Additional Transmitters
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: NOTE: • The interior lights will turn off if you place the ignition • Perchlorate Material — special handling may apply. in the ACC or ON/RUN position while the Panic See www.dtsc.ca.gov/hazardouswaste/perchlorate Alarm is activated.
Page 27 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Emergency Key Removal Separating RKE Transmitter Case 2. Insert the tip of the emergency key or a #2 flat blade 3. Remove the battery by turning the back cover over screwdriver into the slot and gently pry the two halves (battery facing downward) and tapping it lightly on a of the RKE transmitter apart.
Page 28: General Information
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE new battery with your fingers. Skin oils may cause NOTE: Changes or modifications not expressly approved battery deterioration. If you touch a battery, clean it by the party responsible for compliance could void the with rubbing alcohol.
Page 29: How To Use Remote Start
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 How To Use Remote Start WARNING! All of the following conditions must be met before the • Do not start or run an engine in a closed garage or engine will remote start: confined area.
Page 30: To Enter Remote Start Mode
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Remote Start Aborted — Hood Ajar NOTE: • Remote Start Aborted — Fuel Low • If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds. •...
Page 31: To Exit Remote Start Mode And Drive The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 NOTE: To avoid unintentional shutdowns, the system feature will stay on through the duration of Remote Start will disable the one time push of the REMOTE START or until the ignition switch is turned to the ON/RUN button for two seconds after receiving a valid Remote position.
Page 32: Door Locks
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. This device must accept any interference received, including interference that may cause undesired op- eration. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Page 33: Power Door Locks
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 WARNING! WARNING! (Continued) leave the ignition of a vehicle equipped with • For personal security and safety in the event of a Keyless Enter-N-Go in the in the ACC or ON/RUN collision, lock the vehicle doors before you drive as mode.
Page 34 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you push the power door lock switch, with the ignition in the ON/RUN or ACC position and any front door is open, the power locks will not operate. This prevents you from accidentally locking the Key Fob in the vehicle.
Page 35: Child-Protection Door Lock System - Rear Doors
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Auto Unlock On Exit NOTE: Use the Automatic Unlock Doors On Exit feature in accordance with local laws. The doors will unlock automatically on vehicles with power door locks if: Child-Protection Door Lock System — Rear Doors 1.
Page 36 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child-Protection Door Lock Location Child-Protection Door Lock Function 3. Repeat steps 1 and 2 for the opposite rear door. NOTE: When the Child-Protection Door Lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position.
Page 37 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 To Disengage The Child-Protection Door Lock WARNING! System Avoid trapping anyone in a vehicle in a collision. 1. Open the rear door. Remember that the rear doors can only be opened 2. Insert the tip of the emergency key (or alike) into the from the outside when the Child-Protection locks are child lock control and rotate it to the UNLOCK engaged.
Page 38: Keyless Enter-N-Go
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE KEYLESS ENTER-N-GO The Passive Entry system is an enhancement to the vehicle’s Remote Keyless Entry (RKE) system and a feature of Keyless Enter-N-Go. This feature allows you to lock and unlock the vehicle’s door(s) without having to push the RKE transmitter lock or unlock buttons.
Page 39 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 To Unlock From The Driver’s Side: NOTE: If “Unlock All Doors 1st Press” is programmed all doors will unlock when you grab hold of the driver’s With a valid Passive Entry RKE transmitter within 5 ft front door handle.
Page 40 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Preventing Inadvertent Locking Of Passive Entry RKE To Enter The Liftgate: Transmitter In Vehicle: With a valid Passive Entry RKE transmitter within 3 ft To minimize the possibility of unintentionally locking a (1.0 m) of the liftgate, push the button underneath the left Passive Entry RKE transmitter inside your vehicle, the side of the accent bar, which is located on the liftgate...
Page 41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 To Lock The Vehicle’s Doors: Do NOT grab the door handle, when pushing the door handle button. This could unlock the door(s). With one of the vehicle’s Passive Entry RKE transmitters within 5 ft (1.5 m) of the driver or passenger front door handle, push the door handle LOCK button to lock all four doors and liftgate.
Page 42: General Information
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: General Information • After pushing the door handle button, you must wait The following regulatory statement applies to all radio frequency (RF) devices equipped in this vehicle: two seconds before you can lock or unlock the doors, using either Passive Entry door handle.
Page 43: Windows
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 WINDOWS There are single window controls on each passenger door trim panel, which operate the passenger door windows. Power Windows The window controls will operate when the ignition is in The window controls on the driver’s door trim panel the ON/RUN or ACC position.
Page 44 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto-Up Feature With Anti-Pinch Protection WARNING! (Continued) On some models, the driver and front passenger power particularly unattended children, can become en- window switches have an Auto-up feature. Pull the trapped by the windows while operating the power window switch up to the second detent, release, and the window switches.
Page 45 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 • Any impact due to rough road conditions may trigger 2. Push the window switch down firmly to the second the auto-reverse function unexpectedly during auto- detent to open the window completely and continue closure.
Page 46: Wind Buffeting
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, then open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sun- roof opening to minimize the buffeting.
Page 47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 NOTE: The liftgate cannot be unlocked or locked with the manual door lock plungers on the door trim panels or the door lock cylinder on the driver’s door. To open the unlocked liftgate, squeeze the handle and pull the liftgate toward you.
Page 48: Occupant Restraint Systems
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Important Safety Precautions WARNING! Please pay close attention to the information in this • Driving with the liftgate open can allow poisonous section. It tells you how to use your restraint system exhaust gases into your vehicle.
Page 49 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 restraints or belt-positioning booster seats. Older chil- side air bags will inflate forcefully into the space dren who do not use child restraints or belt- between occupants and the door and occupants could positioning booster seats should ride properly buckled be injured.
Page 50: Seat Belt Systems
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Systems their seat belts. The Belt Alert feature is active when- ever the ignition switch is in the START or ON/RUN Buckle up even though you are an excellent driver, even position.
Page 51 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 and the driver or outboard front seat passenger is un- The outboard front passenger seat BeltAlert is not active buckled (if equipped with outboard front passenger seat when the outboard front passenger seat is unoccupied. BeltAlert).
Page 52 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belts WARNING! (Continued) All seating positions in your vehicle are equipped with • In a collision, you and your passengers can suffer lap/shoulder belts. much greater injuries if you are not properly buck- led up.
Page 53 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 WARNING! (Continued) WARNING! (Continued) • Wearing your seat belt incorrectly could make your • A twisted seat belt may not protect you properly. In injuries in a collision much worse. You might a collision, it could even cut into you.
Page 54 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • A seat belt that is worn under your arm is danger- frays, or loose parts. Damaged parts must be re- ous. Your body could strike the inside surfaces of placed immediately.
Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Pulling Out Lap/Shoulder Belt Inserting Latch Plate Into Buckle 3. When the seat belt is long enough to fit, insert the latch 4. Position the lap belt so that it is snug and lies low plate into the buckle until you hear a “click.”...
Page 56 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE position. If necessary, slide the latch plate down the webbing to allow the seat belt to retract fully. Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1.
Page 57 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Adjustable Upper Shoulder Belt Anchorage In the driver and front passenger seats, the top of the shoulder belt can be adjusted upward or downward to position the seat belt away from your neck. Push or squeeze the anchorage button to release the anchorage, and move it up or down to the position that serves you best.
Page 58 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The adjustable upper shoulder belt anchorage is WARNING! equipped with an Easy Up feature. This feature allows • ONLY use a Seat Belt Extender if it is physically the shoulder belt anchorage to be adjusted in the upward position without pushing or squeezing the release but- required in order to properly fit the original seat ton.
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 Seat Belts And Pregnant Women Position the lap belt snug and low below the abdomen and across the strong bones of the hips. Place the shoulder belt across the chest and away from the neck. Never place the shoulder belt behind the back or under the arm.
Page 60 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The pretensioners are triggered by the Occupant Re- Restraints Using The Vehicle Seat Belt” under the “Child straint Controller (ORC). Like the air bags, the preten- Restraints” section of this manual. The table below sioners are single use items.
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 If the passenger seating position is equipped with an WARNING! ALR and is being used for normal usage, only pull the • Never place a rear-facing child restraint in front of seat belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate an air bag.
Page 62 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Disengage The Automatic Locking Mode WARNING! (Continued) Unbuckle the combination lap/shoulder belt and allow it only used to install rear-facing or forward-facing to retract completely to disengage the Automatic Locking child restraints that have a harness for restraining Mode and activate the vehicle sensitive (emergency) the child.
Page 63 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 the Active Head Restraints (AHR) to deploy. If a rear impact requires deployment, both the driver and front passenger seat AHRs will be deployed. When AHRs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the AHR.
Page 64 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) as loose cargo could contact the Active Head Re- • All occupants, including the driver, should not straint during sudden stops. Failure to follow this operate a vehicle or sit in a vehicle’s seat until the warning could cause personal injury if the Active head restraints are placed in their proper positions Head Restraint is deployed.
Page 65: Supplemental Restraint System (Srs)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 US LLC dealer must reset the AHRs on the driver’s and WARNING! front passenger’s seat before driving. Personally attempt- ing to reset the AHRs may result in damage to the AHRs Deployed AHRs are not able to best protect you in all that could impair their function.
Page 66 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Supplemental Side Air Bags • Supplemental Knee Air Bags • Front and Side Impact Sensors • Seat Belt Pretensioners • Seat Belt Buckle Switch • Seat Track Position Sensors Advanced Front Air Bags This vehicle has Advanced Front Air Bags for both the driver and front passenger as a supplement to the seat Advanced Front Air Bag And Knee Bolster Locations...
Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 output appropriate to the severity and type of collision as WARNING! determined by the Occupant Restraint Controller (ORC), • Being too close to the steering wheel or instrument which may receive information from the front impact sensors or other system components.
Page 68 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) some collisions, air bags won’t deploy at all. Al- • No objects should be placed over or near the air ways wear your seat belts even though you have air bag on the instrument panel or steering wheel, bags.
Page 69 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Because air bag sensors measure vehicle deceleration Knee Impact Bolsters over time, vehicle speed and damage by themselves are The Knee Impact Bolsters help protect the knees of the not good indicators of whether or not an air bag should driver and front passenger, and position the front occu- have deployed.
Page 70 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE provides enhanced protection during a frontal impact by working together with the seat belts, pretensioners, and Advanced Front Air Bags. Supplemental Side Air Bags Your vehicle is equipped with two types of side air bags: 1.
Page 71 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 through the seat seam into the space between the occupant and the door. The SAB moves at a very high speed and with such a high force that it could injure occupants if they are not seated properly, or if items are positioned in the area where the SAB inflates.
Page 72 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE injury reduction potential provided by the seat belts and WARNING! body structure. • Your vehicle is equipped with left and right The SABICs deploy downward, covering the side win- Supplemental Side Air Bag Inflatable Curtains dows.
Page 73 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 The SABICs and SABs (“Side Air Bags”) are designed to help keep you in position, away from inflating Side Air activate in certain side impacts and certain rollover Bags. To get the best protection from the Side Air Bags, events.
Page 74 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Side Air Bags will not deploy in all side collisions, WARNING! (Continued) including some collisions at certain angles, or some side properly. In some collisions, Side Air Bags won’t collisions that do not impact the area of the passenger deploy at all.
Page 75 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 faster-developing event may deploy the seat belt preten- deploy and unfold. The abrasions are similar to fric- sioners as well as the Side Air Bags on both sides of the tion rope burns or those you might get sliding along a vehicle.
Page 76 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Do not drive your vehicle after the air bags have de- Enhanced Accident Response System ployed. If you are involved in another collision, the air In the event of an impact, if the communication network bags will not be in place to protect you.
Page 77 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Enhanced Accident Response System Reset the OFF position or in the ACC position, the air bag Procedure system is not on and the air bags will not inflate. In order to reset the Enhanced Accident Response System The ORC contains a backup power supply system that functions after an event, the ignition switch must be may deploy the air bags even if the battery loses power or...
Page 78 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE While the air bag system is designed to be maintenance WARNING! free, if any of the following occurs, have an authorized dealer service the air bag system immediately. Ignoring the Air Bag Warning Light in your instrument panel could mean you won’t have the air bags to •...
Page 79 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 WARNING! (Continued) WARNING! (Continued) authorized dealer. Only manufacturer approved wiring, including adding any kind of badges or seat accessories may be used. If it is necessary to stickers to the steering wheel hub trim cover or the modify the air bag system for persons with dis- upper right side of the instrument panel.
Page 80: Child Restraints
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Whether or not the driver and passenger safety belts In addition to the vehicle manufacturer, other parties, were buckled/fastened; such as law enforcement, that have the special equip- ment, can read the information if they have access to the •...
Page 81 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 Before buying any restraint system, make sure that it has WARNING! a label certifying that it meets all applicable Safety Standards. You should also make sure that you can install In a collision, an unrestrained child can become a it in the vehicle where you will use it.
Page 82 80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Weight Or Age Recommended Type Of Child Restraint Infants and Children who are two years old or Either an Infant Carrier or a Convertible Toddlers younger and who have not reached the Child Restraint, facing rearward in the rear...
Page 83 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Infants And Child Restraints carrier but are still less than at least two years old. Children should remain rear-facing until they reach the Safety experts recommend that children ride rear-facing highest weight or height allowed by their convertible in the vehicle until they are two years old or until they child seat.
Page 84 82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Older Children And Child Restraints WARNING! Children who are two years old or who have outgrown Do not install a rear-facing car seat using a rear support their rear-facing convertible child seat can ride forward- leg in this vehicle.
Page 85 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 seat. The child and belt-positioning booster seat are held WARNING! (Continued) in the vehicle by the seat belt. • When your child restraint is not in use, secure it in the vehicle with the seat belt or LATCH anchor- WARNING! ages, or remove it from the vehicle.
Page 86 84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To position a child into the Integrated Child Booster Seat follow these steps: 1. Slide the second row seat to the full rear position to use the Integrated Child Booster Seat. NOTE: The second row bench with Integrated Child Booster Seat must remain in the full rear position during use.
Page 87 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 6. Slide the latch plate up the webbing as far as necessary to allow the seat belt to go around the child’s lap. NOTE: The lap portion of the seat belt should be low on the hips and as snug as possible.
Page 88 86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Securely lock the seat cushion into position before using the seat. Otherwise, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat cushion could cause serious injury or death.
Page 89 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 2. Do the child’s knees bend comfortably over the front position. If the shoulder belt contacts the face or neck, of the vehicle seat – while they are still sitting all the move the child closer to the center of the vehicle, or use way back? a booster seat to position the seat belt on the child...
Page 90 88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Recommendations For Attaching Child Restraints Restraint Type Combined Use any attachment method shown with an “X” Below Weight of the LATCH – Seat Belt Only LATCH – Seat Belt + Top Child + Child Lower Anchors Lower Anchors Tether Anchor...
Page 91 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 Lower Anchors And Tethers For CHildren seating position. These anchorages are used to install (LATCH) Restraint System LATCH-equipped child seats without using the vehicle’s seat belts. Some seating positions may have a top tether anchorage but no lower anchorages.
Page 92 90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH Positions For Installing Child Restraints In This Vehicle Lower Anchor / Top Tether Locations (Third Row Shown – If Equipped) • Lower Anchorage Symbol 2 anchorages per seating position • Top Tether Anchorage Symbol...
Page 93 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 Child Restraint LATCH Positions Frequently Asked Questions About Installing Child Restraints With LATCH What is the weight limit (child’s weight + 65 lbs (29.5 kg) Use the LATCH anchorage system until the weight of the child restraint) for using the combined weight of the child and the child LATCH anchorage system to attach the child...
Page 94 92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Frequently Asked Questions About Installing Child Restraints With LATCH Can the rear-facing child restraint touch the The child seat may touch the back of the back of the front passenger seat? front passenger seat if the child restraint manufacturer also allows contact.
Page 95 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 Locating LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint.
Page 96 94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE tether strap. The tether strap will have a hook at the end to attach to the top tether anchorage and a way to tighten the strap after it is attached to the anchorage. Center Seat LATCH This vehicle has 5 lower LATCH anchorages in the rear seat.
Page 97 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 and buckle, the center seat belt can be used to restrain an occupant or child restraint in the center seating position. 2. Left outboard and center seating positions (3 and 2): Install the first child seat in the left outboard seating position using lower anchorages D and E.
Page 98 96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Always follow the directions of the child restraint manu- WARNING! (Continued) facturer when installing your child restraint. Not all child child restraint using anchorages C and D. This is restraint systems will be installed as described here. not a LATCH-compatible position in your vehicle.
Page 99 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 forward and rearward in the vehicle, you may wish to 6. Test that the child restraint is installed tightly by move it to its rear-most position to make room for the pulling back and forth on the child seat at the belt child seat.
Page 100 98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the seat belt tight around the child restraint so that it is WARNING! not necessary to use a locking clip. The ALR retractor can • Improper installation of a child restraint to the be “switched”...
Page 101 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 Lap/Shoulder Belt Systems For Installing Child Restraints In This Vehicle Third Row Shown – If Equipped • ALR - Switchable Automatic Locking Retractor • CINCH = Cinching Latchplate...
Page 102 100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Frequently Asked Questions About Installing Child Restraints With Seat Belts What is the weight limit (child’s weight + Weight limit of Always use the tether anchor when using weight of the child restraint) for using the the Child the seat belt to install a forward facing child Tether Anchor with the seat belt to attach a...
Page 103 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 101 Installing A Child Restraint With A Switchable 5. To lock the seat belt, pull down on the shoulder part of Automatic Locking Retractor (ALR) the belt until you have pulled all the seat belt webbing out of the retractor.
Page 104 102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE strap. See the section “Installing Child Restraints rear-most position to make room for the child seat. Using the Top Tether Anchorage” for directions to You may also move the front seat forward to allow attach a tether anchor.
Page 105 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 103 strap. See the section “Installing Child Restraints If the belt still cannot be tightened after you shorten the Using the Top Tether Anchorage” for directions to buckle, disconnect the latch plate from the buckle, turn attach a tether anchor.
Page 106 104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) (LATCH) Restraint System” for the location of ap- proved tether anchorages in your vehicle. 1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. Seat Track Release Lever You may need to move the seat forward to provide 2.
Page 107 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 105 between the two posts. If not possible, lower the head 4. Remove slack in the tether strap according to the child restraint and pass the tether strap around the outboard restraint manufacturer’s instructions. side of the head restraint.
Page 108: Transporting Pets
106 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transporting Pets While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. Air Bags deploying in the front seat could harm your pet. Wide-open throttle acceleration in low gear can be detri- An unrestrained pet will be thrown about and possibly mental and should be avoided.
Page 109: Safety Tips
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 107 NOTE: A new engine may consume some oil during its WARNING! (Continued) first few thousand miles (kilometers) of operation. This • It is extremely dangerous to ride in a cargo area, should be considered a normal part of the break-in and inside or outside of a vehicle.
Page 110: Exhaust Gas
108 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • On seven passenger models, do not allow a passen- • Do not run the engine in a closed garage or in ger to sit in a third row seat with the second row confined areas any longer than needed to move seatback(s) folded flat.
Page 111: Safety Checks You Should Make Inside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 109 Whenever a change is noticed in the sound of the exhaust Front seat belt assemblies must be replaced after a system, when exhaust fumes can be detected inside the collision. Rear seat belt assemblies must be replaced after vehicle, or when the underside or rear of the vehicle is a collision if they have been damaged (i.e., bent retractor, damaged, have a competent mechanic inspect the com-...
Page 112 110 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Floor Mat Safety Information WARNING! (Continued) Always use floor mats designed to fit the footwell of your • Never place or install floor mats or other floor vehicle. Use only floor mats that leave the pedal area coverings in the vehicle that cannot be properly unobstructed and that are firmly secured so that they secured to prevent them from moving and interfer-...
Page 113: Periodic Safety Checks You Should Make Outside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 111 lodged in the tread or sidewall. Inspect the tread for cuts WARNING! (Continued) and cracks. Inspect sidewalls for cuts, cracks, and bulges. • Always make sure that objects cannot fall into the Check the wheel nuts for tightness.
Page 115 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS ▫ Uconnect 4.3 ......124 MIRRORS ......119 ▫...
Page 116 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Operation ......151 ▫ Front Heated Seats — If Equipped ..202 ▫...
Page 117 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 ▫ Flash-To-Pass ......229 LIGHTS ......224 ▫...
Page 118 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Service The ParkSense Rear Park Assist ELECTRONIC SPEED CONTROL — IF EQUIPPED ......238 System .
Page 119 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 ▫ Programming A Non-Rolling Code ..259 ▫ Sunshade Operation....267 ▫...
Page 120 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Flip ’n Stow Front Passenger Seat Storage — If ▫ Cargo Management System ....283 Equipped ......279 REAR WINDOW FEATURES .
Page 121: Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 MIRRORS Inside Day/Night Mirror — If Equipped The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).
Page 122 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. This mirror automatically adjusts for headlight glare from vehicles behind you. NOTE: • The Automatic Dimming Mirror feature is disabled when the vehicle is in reverse gear to improve rear view viewing.
Page 123: Outside Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Outside Mirrors Power Mirrors To receive maximum benefit, adjust the outside mirror(s) The power mirror switch is located on the driver’s door to center on the adjacent lane of traffic and a slight trim panel.
Page 124: Power Folding Mirrors - If Equipped
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Models Without Express Window Feature Push the switch once and the mirrors will fold in, pushing the switch a second time will return the mirrors Push the mirror select button marked L (left) or R (right) to the normal driving position.
Page 125: Manual Folding Mirrors - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 If the mirrors are in the folded position, and vehicle Manual Folding Mirrors — If Equipped speed is equal or greater than 10 mph (16 km/h), they Some models have exterior mirrors that are hinged. The will automatically unfold.
Page 126: Uconnect Phone (4.3)
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull the sun visor toward the inside rearview mirror to extend it. UCONNECT PHONE (4.3) Uconnect 4.3 Uconnect Phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect Phone allows you to dial a phone number with your mobile phone. Uconnect Phone supports the following features: Voice Activated Features: •...
Page 127 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 • View Call logs on screen (“Show incoming calls,” • Pairing up to 10 phones/audio devices for easy access “Show Outgoing calls,” “Show missed Calls,” “Show to connect to them quickly Recent Calls”) Your mobile phone’s audio is transmitted through your •...
Page 128 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect Phone allows you to transfer calls between the works no matter where you stow your mobile phone (be system and your mobile phone as you enter or exit your it your purse, pocket, or briefcase), as long as your phone vehicle and enables you to mute the system’s microphone is turned on and has been paired to the vehicle’s for private conversation.
Page 129: Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Uconnect Voice Command Button 1. Say compound commands like “Call John Smith mo- bile.” The Uconnect Voice Command Button is only used for “barge in” and when you are 2. Say the individual commands and allow the system to already in a call and you want to send Tones guide you to complete the task.
Page 130 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE say each part of the command when you are asked for The system handles multiple inputs in the same phrase it. For example, you can use the compound command or sentence such as “make a phone call” and “to Kelly form voice command “Search for John Smith,”...
Page 131 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Help Command Pair (Link) Uconnect Phone To A Mobile Phone If you need assistance at any prompt, or if you want to To begin using your Uconnect Phone, you must pair your know your options at any prompt, say “Help” following compatible Bluetooth enabled mobile phone.
Page 132 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE b. Push the MORE button on the faceplate, then press this phone the highest priority. This phone will take the “Phone” button on the touchscreen and you precedence over other paired phones within range. will go to the Uconnect Phone main screen.
Page 133 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 this device the highest priority. This device will take 2. Press the “Phone/Bluetooth” button on the touch- precedence over other paired devices within range. screen. NOTE: If No is selected, device priority is determined by 3.
Page 134 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Press the “X” to exit out of the Settings screen. 3. Select a different Phone or Audio Device then the currently connected device. Deleting A Phone Or Audio Device 4. At the Options pop-up screen press the “Make Favor- 1.
Page 135 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 • Automatic download and update of a phone book, if edited on the mobile phone. The changes are trans- supported, begins as soon as the Bluetooth wireless ferred and updated to Uconnect Phone on the next phone connection is made to the Uconnect Phone, for phone connection.
Page 136: Phone Call Features
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Recent Call Log 4. Follow the on-screen prompts to complete the task. Phone Call Features NOTE: All of the above operations except Redial can be done with one call or less active. The following features can be accessed through the Uconnect Phone if the feature(s) are available on your Dial By Saying A Number...
Page 137 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 3. The Uconnect Phone will dial the number associated Touch-Tone Number Entry with John Doe, or if there are multiple numbers it will 1. Press the “Phone” button on the touchscreen. ask which number you want to call for John Doe. 2.
Page 138 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Outgoing Calls Ignore. Press the Answer button on the touchscreen or push the Phone button on the steering wheel to • Missed Calls accept the call. • All Calls Answer Or Reject An Incoming Call — Call These can be accessed by touching the recent calls button Currently In Progress on the touchscreen on the Phone main screen.
Page 139 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Making A Second Call While Current Call Is In hold at a time. Also you can press the “Swap” button Progress on the touchscreen, on the Phone main screen. To make a second call while you are currently on a call, Join Calls push the Voice Command button and say “Dial”...
Page 140: Uconnect Phone Features
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Redial Uconnect Phone Features 1. Press the “Redial” button on the touchscreen, or push Emergency Assistance the Phone button and after the “Listening” If you are in an emergency and the mobile phone is prompt and the following beep, say “Redial.”...
Page 141 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 NOTE: Roadside Assistance/Towing Assistance • The emergency number dialed is based on the country If you need roadside/towing assistance: where the vehicle is purchased (911 for the U.S. and • Push the Phone button to begin.
Page 142 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Working With Automated Systems numbers, is also to be used for navigating through an automated customer service center menu structure, This method is used in instances where one generally has and to leave a number on a pager. to push numbers on the mobile phone keypad while navigating through an automated telephone system.
Page 143 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 • You may not hear all of the tones due to mobile phone Say the full name” you could push the Voice Com- network configurations. This is normal. mand button and say, “John Smith” to select that option without having to listen to the rest of the voice •...
Page 144: Advanced Phone Connectivity
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phone And Network Status Indicators NOTE: Certain brands of mobile phones do not send the dial ring to the Uconnect Phone to play it on the vehicle Uconnect Phone will provide notification to inform you audio system, so you will not hear it.
Page 145: Uconnect Phone
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 • Always wait for the beep before speaking. without terminating the call. To transfer an ongoing call from your connected mobile phone to the Uconnect • Speak normally without pausing, just as you would Phone or vice versa, press the “Transfer”...
Page 146 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You can say “O” (letter “O”) for “0” (zero). NOTE: • Even though the system is designed for users speaking • Even though international dialing for most number in North American English, French, and Spanish ac- combinations is supported, some shortcut dialing cents, the system may not always work for some.
Page 147 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 • Performance, such as audio clarity, echo, and loudness Power-Up to a large degree rely on the phone and network, and After switching the ignition key from OFF to either the not the Uconnect Phone ON or ACC position, or after a language change, you •...
Page 148 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Tree...
Page 149: General Information
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 • You can replace “4” with any message number shown NOTE: on the screen. • You can replace “John Smith” with any name in your • If your phone does not support phonebook download mobile or favorite phone book.
Page 150: Uconnect Phone (8.4/8.4N)
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • This device must accept any interference received, • Hands Free text messaging (“Send a message to John including interference that may cause undesired op- Smith Mobile”). eration. • Redialing last dialed numbers (“Redial”). UCONNECT PHONE (8.4/8.4N) •...
Page 151 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 • Setting Favorite Contact Phone numbers so they are NOTE: Your phone must be capable of SMS messaging easily accessible on the Main Phone screen. via Bluetooth for messaging features to work properly. Your mobile phone’s audio is transmitted through your •...
Page 152 150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Uconnect Phone allows up to ten mobile phones or WARNING! audio devices to be linked to the system. Only one linked (or paired) mobile phone and one audio device can be Any voice commanded system should be used only used with the system at a time.
Page 153: Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 The Voice Command button is also used to access 2. Say the individual commands and allow the system to the Voice Commands for the Uconnect Voice Com- guide you to complete the task. mand features if your vehicle is equipped.
Page 154 152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE form voice command “Search for John Smith,” or you Smith.” For multiple inputs in the same phrase or sen- can break the compound command form into two tence, the system identifies the topic or context and voice commands: “Search Contact”...
Page 155 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 To activate the Uconnect Phone from idle, simply push NOTE: the Phone button on your steering wheel and say a • You must have Bluetooth enabled on your mobile command or say “help.” All Uconnect Phone sessions phone to complete this procedure.
Page 156 154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Press the “Add Device” button on the touchscreen. • Search for available devices on your Bluetooth en- abled mobile phone. When prompted on the phone, enter the name and PIN shown on the Uconnect screen.
Page 157 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Pair Additional Mobile Phones 1. Press the “Settings” button from the Phone main screen. 2. Press the “Add Device” button on the touchscreen. 3. Search for available devices on your Bluetooth enabled mobile phone. When prompted on the phone, enter the name and PIN shown on the Uconnect screen.
Page 158 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: For phones which are not made a favorite, the NOTE: If there is no device currently connected with the phone priority is determined by the order in which it was system, a pop-up will appear. paired.
Page 159 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 You can also use the following VR command to bring up 4. Press the “X” to exit out of the Settings screen. a list of paired audio devices: Disconnecting A Phone Or Audio Device •...
Page 160 158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Press the “Pair Phones” or “Paired Audio Devices” 5. Press the “Make Favorite” button on the touchscreen; button on the touchscreen. you will see the chosen device move to the top of the list.
Page 161 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 • Automatic download and update of a phone book, if edited on the mobile phone. The changes are trans- supported, begins as soon as the Bluetooth wireless ferred and updated to Uconnect Phone on the next phone connection is made to the Uconnect Phone, for phone connection.
Page 162 160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE record. Select an empty entry and press the “+” on that selected entry. When the Options pop-up appears, press “Add from Mobile.” You will then be asked which contact and number to choose from your mo- bile phonebook.
Page 163 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 To Remove A Favorite 1. To remove a Favorite, select phonebook from the Phone main screen. 2. Next select Favorites on the left side of the screen and then press the “+” Options button on the touchscreen. 3.
Page 164 162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Emergency And Towing Assistance The Emergency and Towing Assistance Favorite numbers can only be altered. These cannot be deleted and the names cannot be changed. To change the Emergency or Towing Assistance numbers follow these steps.
Page 165: Phone Call Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 • Mobile Phonebook Phone Call Features • Recent Call Log The following features can be accessed through the Uconnect Phone if the feature(s) are available and sup- • SMS Message Viewer ported by Bluetooth on your mobile service plan. For example, if your mobile service plan provides three-way Dial By Saying A Number calling, this feature can be accessed through the Uconnect...
Page 166 164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. The Uconnect Phone will dial the number associated Touch-Tone Number Entry with John Doe, or if there are multiple numbers it will 1. Press the “Phone” button on the touchscreen. ask which number you want to call for John Doe. 2.
Page 167 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 • Missed Calls Recent Calls • All Calls You may browse up to 34 of the most recent of each of the following call types: These can be accessed by pressing the “recent calls” button on the touchscreen on the Phone main screen.
Page 168 166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Push the Phone button on the steering wheel to Making A Second Call While Current Call Is In accept the call. You can also press the “answer” button Progress on the touchscreen or press the caller ID box. You can place a call on hold by pressing the “Hold”...
Page 169 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 Toggling Between Calls Redial If two calls are in progress (one active and one on hold), Press the “Redial” button on the touchscreen, or push the press the “Swap” button on the Phone main screen. Only Phone button and after the “Listening”...
Page 170: Uconnect Phone Features
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect Phone Features NOTE: • The Emergency call may also be initiated by using the Emergency Assistance touchscreen. If you are in an emergency and the mobile phone is • The emergency number dialed is based on the country reachable: where the vehicle is purchased (911 for the U.S.
Page 171 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 NOTE: The roadside/towing assistance number dialed is WARNING! based on the country where the vehicle is purchased (1-800-521-2779 for the U.S./Canada, 55-14-3454 for Your phone must be turned on and connected to the Mexico City and 1-800-712-3040 for outside Mexico City Uconnect Phone to allow use of this vehicle feature in Mexico).
Page 172 170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Working With Automated Systems numbers, is also to be used for navigating through an automated customer service center menu structure, This method is used in instances where one generally has and to leave a number on a pager. to push numbers on the mobile phone keypad while navigating through an automated telephone system.
Page 173 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 • You may not hear all of the tones due to mobile phone Say the full name” you could push the Voice Com- network configurations. This is normal. mand button and say, “John Smith” to select that option without having to listen to the rest of the voice •...
Page 174 172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phone And Network Status Indicators NOTE: Certain brands of mobile phones do not send the dial ring to the Uconnect Phone to play it on the vehicle Uconnect Phone will provide notification to inform you audio system, so you will not hear it.
Page 175: Advanced Phone Connectivity
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 Advanced Phone Connectivity Things You Should Know About Your Uconnect Phone Transfer Call To And From Mobile Phone Voice Command The Uconnect Phone allows ongoing calls to be trans- ferred from your mobile phone to the Uconnect Phone For the best performance: without terminating the call.
Page 176 174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Performance is maximized under: Even though the system is designed for many languages and accents, the system may not always work for some. • Low-To-Medium Blower Setting NOTE: It is recommended that you do not store names in •...
Page 177 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 • Smooth Road Surface Your phone must support SMS over Bluetooth to use this feature. If the Uconnect Phone determines your phone is • Fully Closed Windows not compatible with SMS messaging over Bluetooth the •...
Page 178 176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Uconnect Phone SMS is only available when the vehicle is not moving. Read Messages: If you receive a new text message while your phone is connected to Uconnect Phone, an announcement will be made to notify you that you have a new text message.
Page 179 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 Send Messages Using Buttons On The Touchscreen: You can send messages using Uconnect Phone. To send a new message: 1. Press the “Phone” button on the touchscreen. 2. Press the “messaging” button on the touchscreen then “New Message.”...
Page 180 178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Send Messages Using Voice Commands: 1. Push the Phone button. 2. After the “Listening” prompt and the following beep, say “Send message to John Smith mobile.” 3. After the system prompts you for what message you want to send, say the message you wish to send or say “List.”...
Page 181 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 4. I can’t talk right now. 17. I’m lost. 5. Call me. 18. See you later. 6. I’ll call you later. Bluetooth Communication Link Mobile phones have been found to lose connection to the 7.
Page 182 180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Tree...
Page 183 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 NOTE: 6. Send dial tones for automated systems is available while a call is active. This is an example that uses a 1. You can replace “John Smith” with any name in your Phonebook Record named “Voicemail Password.”...
Page 184 182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 185 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 NOTE: 6. You can replace “4” with any message number shown on the screen. 1. You can replace “John Smith” with any name in your mobile or favorite phone book. You can also say “Send 7.
Page 186 184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 187: General Information
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 NOTE: Available Voice Commands are shown in bold VOICE COMMAND face and underlined in the gray shaded boxes. Uconnect 8.4/8.4 Nav General Information This device complies with Part 15 of the FCC rules and The Uconnect Voice Command system allows RSS 210 of Industry Canada.
Page 188 186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If no command is spoken the system will say one of two WARNING! responses: Any voice commanded system should be used only • I didn’t understand in safe driving conditions following all applicable •...
Page 189 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 Pushing the Uconnect Voice Command button while The system will best recognize your speech if the win- the system is speaking is known as “barging in.” The dows are closed, and the heater/air conditioning fan is system will be interrupted, and after the beep, you can set to low.
Page 190: Uconnect Voice Commands
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Natural Speech The system utilizes continuous dialog; when the system requires more information from the user it will ask a Natural speech allows the user to speak commands in question to which the user can respond without pressing phrases or complete sentences.
Page 191 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 Changing The Volume Starting Voice Recognition (VR) Session In Radio/Player Modes 1. Start a dialogue by pushing the Voice Command In this mode, you can say the following commands: button. NOTE: The commands can be said on any screen when 2.
Page 192 190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Tree...
Page 193 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 NOTE: • You can replace “950 AM” with any other AM or FM frequency, such as “98.7 FM.” • You can replace “80’s on 8” with any other satellite station name received by the radio. •...
Page 194 192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 195 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 NOTE: • You can replace the album, artist, song, genre, playlist, podcast and audio book names with any correspond- ing names on the current device that is playing. • You can replace “8” with any track on the CD that is currently playing.
Page 196 194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 197 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 NOTE: • You can replace “NFL” with any league shown on the sports league screen. For example you can say “Show MLB headlines” or “Show PGA headlines.” • You can replace “Headlines” with any menu items shown on a league screen.
Page 198 196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 199 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 NOTE: • Only available with Navigation equipped vehicles. • You can replace “Player” with “Radio,” “Navigation,” “Phone,” “Climate,” “More” or “Settings.” • Navigation commands only work if equipped with Navigation. • Available Voice Commands are shown in bold face and shaded grey.
Page 200 198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 201: Seats
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 NOTE: WARNING! • You can also say “Find City,” “Find Favorite,” “Find • It is dangerous to ride in a cargo area, inside or Play by Category,” “Find Play by Name,” “Find Re- outside of a vehicle.
Page 202 200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjusting The Seat Up Or Down The height of the seats can be adjusted up or down. Pull upward or push downward on the seat switch. The seat will move in the direction of the switch. Release the switch when the desired position is reached.
Page 203: Power Lumbar - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 WARNING! CAUTION! • Adjusting a seat while driving may be dangerous. Do not place any article under a power seat or Moving a seat while driving could result in loss of impede its ability to move as it may cause damage to control which could cause a collision and serious the seat controls.
Page 204: Front Heated Seats - If Equipped
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Heated Seats — If Equipped The front heated seats control buttons are located within the Uconnect system. You can gain access to the control buttons through the climate screen or the controls screen. •...
Page 205: Manual Front Seat Adjustments
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 NOTE: The engine must be running for the heated seats WARNING! (Continued) to operate. even at low temperatures, especially if used for Vehicles Equipped With Remote Start long periods of time. • Do not place anything on the seat or seatback that On models that are equipped with remote start, the insulates against heat, such as a blanket or cushion.
Page 206: Recliner Adjustment
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked.
Page 207: Driver's Seat Height Adjustment - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 WARNING! (Continued) adjusted properly and you could be injured. Adjust the seat only while the vehicle is parked. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
Page 208: Fold-Flat Front Passenger Seat - If Equipped
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE hardback surface that you can use as a work surface when the seat is folded flat and the vehicle is not in motion. Seat Height Adjustment Lever Fold-Flat Front Passenger Seat — If Equipped This feature allows for extended cargo space.
Page 209: Head Restraints
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 WARNING! WARNING! Adjusting a seat while the vehicle is moving is The head restraints for all occupants must be prop- dangerous. The sudden movement of the seat could erly adjusted prior to operating the vehicle or occu- cause you to lose control.
Page 210 208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When AHRs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the AHR. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear impacts.
Page 211 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 Active Head Restraint (Normal Position) Active Head Restraint (Tilted) NOTE: • The head restraints should only be removed by quali- fied technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer.
Page 212 210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • In the event of deployment of an Active Head Re- WARNING! (Continued) straint, refer to “Occupant Restraints/Supplemental • Active Head Restraints may be deployed if they are Active Head Restraints (AHR)/Resetting Active Head struck by an object such as a hand, foot or loose Restraints (AHR)”...
Page 213 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 WARNING! A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle. Always securely stow re- moved head restraints in a location outside the occu- pant compartment.
Page 214: Third Row Passenger Seats - Seven Passenger Models
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Third Row Passenger Seats — Seven Passenger WARNING! (Continued) Models re-installation instructions above prior to operating These head restraints are non-adjustable and non- the vehicle or occupying a seat. removable. However, you can fold them forward when they are not in use by passengers.
Page 215: 60/40 Split Second-Row Passenger Seats
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 60/40 Split Second-Row Passenger Seats WARNING! (Continued) To provide additional storage area, each second-row • Do not allow people to ride in any area of your passenger seat can be folded flat. This allows for ex- vehicle that is not equipped with seats and seat tended cargo space and still maintains some seating room belts.
Page 216 214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! To prevent personal injury or damage to objects, keep your head, arms, and objects out of the folding path of the seatback. 4. Gently guide the seatback into the folded position. To Unfold The Seat Raise the seatback and lock it in place.
Page 217 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 Forward And Rearward Adjustment The control lever is on the outboard side of the seat. Lift the lever to move the seat forward or rearward. Release the lever once the seat is in the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.
Page 218 216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) cause you to lose control. The seat belt might not be adjusted properly and you could be injured. Adjust any seat only while the vehicle is parked. Recliner Adjustment The recline lever is on the outboard side of the seat. To recline the seatback, lean back, lift the lever, position the seatback as desired, and then release the lever.
Page 219 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 WARNING! (Continued) adjusted properly and you could be injured. Adjust the seat only while the vehicle is parked. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
Page 220 218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Move the control lever on the upper outboard side of the WARNING! seatback forward. Then, in one fluid motion, the seat cushion flips upward and the seat moves forward on its Keep the latch clean and free of objects and be tracks.
Page 221 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 WARNING! Do not drive the vehicle with the seat in this posi- tion, as it is only intended for entering and exiting the third row seats. Failure to follow this warning may result in personal injury. To Unfold And Move The Second-Row Passenger Seat Rearward Move the seatback rearward until it locks in place and...
Page 222: 50/50 Split Third-Row Passenger Seats With Fold-Flat Feature - Seven Passenger Models
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Fold The Seatback WARNING! Pull the latch release-loop located at the top of the Be certain that the seatback and seat are locked seatback upward, push the seatback forward slightly, and securely into position. Otherwise, the seat will not release the release-loop.
Page 223 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221 To Unfold The Seatback The seatback can also be locked in the reclined position. To do so, pull the latch release-loop located at the top of Grasp the assist strap loop on the seatback and pull it the seatback upward, allow the seatback to recline, and toward you to raise the seatback.
Page 224: To Open And Close The Hood
222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Do not allow a passenger to sit in a third row seat with the second row seatback(s) folded flat. In a collision, the passenger could slide underneath the seat belt and be seriously or even fatally injured. TO OPEN AND CLOSE THE HOOD Two latches must be released to open the hood.
Page 225 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223 Underhood Safety Latch Hood Prop Rod 3. Use the hood prop rod to secure the hood in the open CAUTION! position. Place the upper end of the prop rod in the hole on the underside of the hood. To prevent possible damage: •...
Page 226: Lights
224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS CAUTION! (Continued) Headlight Switch • Do not slam the hood to close it. Use a firm downward push at the center front edge of the The headlight switch is located on the left side of the hood to ensure that both latches engage.
Page 227: Automatic Headlights - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225 Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch counterclockwise to the AUTO position. When the system is on, the headlight time delay feature is also on.
Page 228: Headlight Time Delay
226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE is set to ON. In addition, the headlights will turn off NOTE: The lights must be turned off within 45 seconds when the wipers are turned off if they were turned on by of turning the ignition OFF to activate this feature.
Page 229: Lights-On Reminder
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227 NOTE: The daytime running lights can be turned on and off using the Uconnect System, refer to “Uconnect Set- tings — Customer Programmable Features” in “Under- standing Your Instrument Panel” for further information. Lights-On Reminder If the headlights or parking lights are on after the ignition is placed in the OFF position, a chime will sound to alert...
Page 230: Multifunction Lever
228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE An indicator light in the instrument cluster illuminates when the fog lights are turned on. NOTE: The fog lights will operate when the low beam headlights or parking lights are on. However, selecting the high beam headlights will turn off the fog lights.
Page 231: Lane Change Assist
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229 NOTE: High/Low Beam Switch • If either light remains on and does not flash, or there is Push the multifunction lever away from you to switch the headlights to high beam. Pull the multifunction lever a very fast flash rate, check for a defective outside light toward you to switch the headlights back to low beam.
Page 232 230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE light. To restore interior light operation, either place the ignition in the ON/RUN position or cycle the light switch. Dimmer Controls The dimmer control is part of the headlight switch and is located on the left side of the instrument panel. Rotating the dimmer control upward with the parking lights or headlights on will increase the brightness of the instru- ment panel lights, door map pockets and cupholders (if...
Page 233: Map/Reading Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231 Interior Light Defeat (OFF) WINDSHIELD WIPERS AND WASHERS Rotate the dimmer control to the extreme bottom off The windshield wiper/washer control lever is located on position. The interior lights will remain off when the the left side of the steering column.
Page 234: Intermittent Wiper System
232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the rear window wiper/washer, refer to “Rear Window Features” in “Understanding The Features Of Your Ve- hicle”. Intermittent Wiper System Use the intermittent wiper system when weather condi- tions make a single wiping cycle, with a variable pause between cycles, desirable.
Page 235: Windshield Wiper Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233 from a minimum of one cycle every second to a maximum of approximately 18 seconds between cycles. NOTE: The wiper delay times depend on vehicle speed. If the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled.
Page 236: Windshield Washers
234 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Washers CAUTION! To use the windshield washer, push the washer knob, • Turn the windshield wipers OFF when driving located on the end of the multifunction lever, inward to through an automatic car wash. Damage to the the second detent.
Page 237: Mist Feature
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 235 Headlights On With Wipers (Available With WARNING! (Continued) Automatic Headlights Only) the windshield during freezing weather, warm the When this feature is active, the headlights will turn on windshield with the defroster before and during after the wipers are turned on if the headlight switch is windshield washer use.
Page 238: Tilt/Telescoping Steering Column
236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT/TELESCOPING STEERING COLUMN To unlock the steering column, push the control handle downward. To tilt the steering column, move the steering This feature allows you to tilt the steering column wheel upward or downward as desired. To lengthen or upward or downward.
Page 239: Heated Steering Wheel - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 237 HEATED STEERING WHEEL — IF EQUIPPED Vehicles Equipped With Remote Start The steering wheel contains a heating element that helps On models that are equipped with remote start, the warm your hands in cold weather. The heated steering heated steering wheel can be programmed to come on wheel has only one temperature setting.
Page 240: Understanding The Features Of Your Vehicle
238 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) wheel covers of any type and material. This may cause the steering wheel heater to overheat. ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, the Electronic Speed Control takes over accelerator operations at speeds greater than 25 mph (40 km/h).
Page 241: To Activate
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 239 NOTE: In order to ensure proper operation, the Elec- WARNING! tronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at Leaving the Electronic Speed Control system on the same time.
Page 242: To Deactivate
240 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate The drivers preferred units can be selected through the instrument panel settings if equipped. Refer to “Under- A soft tap on the brake pedal, pushing the CANCEL standing Your Instrument Panel” for more information. button, or normal brake pressure while slowing the The speed increment shown is dependent on the selected vehicle will deactivate the Electronic Speed Control with-...
Page 243: To Accelerate For Passing
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 241 • If the button is continually pushed, the set speed will • If the button is continually pushed, the set speed will continue to increase until the button is released, then continue to decrease until the button is released, then the new set speed will be established.
Page 244: Parksense Rear Park Assist - If Equipped
242 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Electronic Speed Control system maintains PARKSENSE REAR PARK ASSIST — IF speed up and down hills. A slight speed change on EQUIPPED moderate hills is normal. The ParkSense Rear Park Assist system provides visual and audible indications of the distance between the rear On steep hills, a greater speed loss or gain may occur so fascia and a detected obstacle when backing up, e.g.
Page 245: Parksense Sensors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 243 ParkSense Sensors fascia/bumper and the detected obstacle. Refer to “Elec- tronic Vehicle Information Center (EVIC) Settings” in The four ParkSense sensors, located in the rear fascia/ “Understanding Your Instrument Panel” for further in- bumper, monitor the area behind the vehicle that is formation.
Page 246 244 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Park Assist Ready Park Assist System Off The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the obstacle, the EVIC display will show fewer arcs and the sound tone will change from slow, to fast, to continuous.
Page 247 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 245 Slow Tone Fast Tone...
Page 248 246 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: Continuous Tone...
Page 249: Enabling And Disabling Parksense
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 247 WARNING ALERTS Rear Distance Greater than 79-39 in 39-25 in 25-12 in Less than (in/cm) 79 in (200 cm) (200-100 cm) (100-65 cm) (65-30 cm) 12 in (30 cm) Audible Alert None Single 1/2- Slow Fast Continuous...
Page 250: Cleaning The Parksense System
248 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the “CLEAN PARK ASSIST”, “SERVICE PARK ASSIST”, Cleaning The ParkSense System or “SERVICE PARK ASSIST SYSTEM” message. Refer to Clean the ParkSense sensors with water, car wash soap “Electronic Vehicle Information Center (EVIC)” in “Un- and a soft cloth.
Page 251 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 249 • When you move the shift lever to the REVERSE PARK ASSIST SYSTEM” message to be displayed in position and ParkSense is turned off, the EVIC will the EVIC. display the “PARK ASSIST SYSTEM OFF” message for as long as the vehicle is in REVERSE.
Page 252: Parkview Rear Back Up Camera - If Equipped
250 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) could detect the ball mount and hitch ball assem- • Drivers must be careful when backing up even bly, depending on its size and shape, giving a false when using ParkSense. Always check carefully indication that an obstacle is behind the vehicle.
Page 253 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 251 When the vehicle is shifted out of REVERSE, the rear vehicle to assist with parking or aligning to a hitch/ camera mode is exited and the last selected touchscreen receiver. The static grid lines will show separate zones appears again.
Page 254: Overhead Console
252 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! (Continued) • To avoid vehicle damage, the vehicle must be Drivers must be careful when backing up even when driven slowly when using ParkView to be able to using the ParkView Rear Back Up Camera. Always stop in time when an obstacle is seen.
Page 255: Courtesy/Reading Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 253 courtesy lights also function as reading lights. Push in on each lens to turn these lights on while inside the vehicle. Push the lens a second time to turn each light off. You may adjust the direction of these lights by pushing the outside ring, which is identified with four directional arrows.
Page 256: Sunglasses Storage
254 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunglasses Storage Interior Observation Mirror To access the storage compartment, push on the raised The convex interior observation mirror provides the bars on the compartment door in the center of the console driver and front seat passenger a wide field of view to and release and the door will swing downward.
Page 257: Power Sunroof Switch - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 255 GARAGE DOOR OPENER — IF EQUIPPED HomeLink replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink unit operates off your vehicle’s battery.
Page 258 256 UNDERSTANDING THE FEATURES OF YOUR VEHICLE HomeLink Buttons/Overhead Consoles HomeLink Buttons/Sunvisor/Headliner NOTE: HomeLink is disabled when the Vehicle Security Alarm is active.
Page 259: Before You Begin Programming Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 257 Before You Begin Programming HomeLink NOTE: • Erasing all channels should only be performed when Be sure that your vehicle is parked outside of the garage before you begin programming. programming HomeLink for the first time. Do not erase channels when programming additional buttons.
Page 260 258 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink button you wish to program while keeping the HomeLink indicator light in view. 3. Push and hold the HomeLink button you want to program while you push and hold the hand-held transmitter button.
Page 261: Programming A Non-Rolling Code
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 259 Firmly push and release the “LEARN” or “TRAIN- Reprogramming A Single HomeLink Button ING” button. On some garage door openers/devices (Rolling Code) there may be a light that blinks when the garage door To reprogram a channel that has been previously trained, opener/device is in the LEARN/TRAIN mode.
Page 262 260 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • To program the two remaining HomeLink buttons, 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink button you wish to repeat each step for each remaining button. DO NOT program while keeping the HomeLink indicator light erase the channels.
Page 263: Canadian/Gate Operator Programming
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 261 Canadian/Gate Operator Programming 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink button you wish to For programming transmitters in Canada/United States program while keeping the HomeLink indicator light that require the transmitter signals to “time-out”...
Page 264: Using Homelink
262 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: 2. Push and hold the desired HomeLink button until the indicator light begins to flash after 20 seconds. Do not • If the indicator light stays on constantly, program- release the button. ming is complete and the garage door/device should activate when the HomeLink button is pushed.
Page 265: Troubleshooting Tips
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 263 To do this, push and hold the two outside buttons for 20 If you have any problems, or require assistance, please seconds until the red indicator flashes. Note that all call toll-free 1-800-355-3515 or, on the Internet at channels will be erased.
Page 266: General Information
264 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: WARNING! (Continued) • The transmitter has been tested and it complies with after 1982. Do not use a garage door opener without FCC and IC rules. Changes or modifications not ex- these safety features. Call toll-free 1-800-355-3515 pressly approved by the party responsible for compli- or, on the Internet at HomeLink.com for safety ance could void the user’s authority to operate the...
Page 267 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 265 WARNING! (Continued) accessible to children. Do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go in the ACC or ON/RUN mode. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch.
Page 268: Opening Sunroof - Express
266 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof — Express position. The sunroof will close fully and stop automati- cally. This is called “Express Close.” During Express Push the switch rearward and release it within one-half Close operation, any other actuation of the switch will second.
Page 269: Venting Sunroof - Express
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 267 sunroof will automatically retract. Remove the obstruc- Wind Buffeting tion if this occurs. Next, push the switch forward and Wind buffeting can be described as the perception of release to Express Close. pressure on the ears or a helicopter-type sound in the ears.
Page 270: Ignition Off Operation
268 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ignition Off Operation The power sunroof switch will remain active for up to approximately ten minutes after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature. NOTE: Ignition Off time is programmable through the Uconnect System.
Page 271 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 269 A second 12 Volt (13 Amp) power outlet is located inside A third fused 12 Volt power outlet is located on the back the center console storage area. Power is available with of the center console. This power outlet has power the ignition is in the ON/RUN, ACC or LOCK position.
Page 272 270 UNDERSTANDING THE FEATURES OF YOUR VEHICLE A fourth fused 12 Volt power outlet is located on the left NOTE: To ensure proper operation a MOPAR knob and quarter trim panel in the cargo area. This power outlet element must be used. has power available when the ignition is in the ON or ACC position.
Page 273 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 271 WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. •...
Page 274: Power Inverter - If Equipped
272 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! CAUTION! (Continued) • Power outlets are designed for accessory plugs • Many accessories that can be plugged in draw only. Do not hang any type of accessory or acces- power from the vehicle’s battery, even when not in sory bracket from the plug.
Page 275 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 273 may have to be reset manually. To reset the inverter manually press the power inverter button OFF and ON. To avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter. NOTE: Due to built-in overload protection, the power outlet will shut down if the 115 Volt AC (150 Watt maximum) power rating is exceeded.
Page 276: Power Inverter Operation
274 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Inverter Operation 2. Press the “Outlet” button on the touchscreen to turn the power inverter On or Off. The power inverter is turned On and Off using the Uconnect System. CUPHOLDERS Vehicles Equipped With Uconnect 4.3 There are two cupholders, located in the center floor console, for the front passengers.
Page 277 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 275 For passengers in the second row there are two cuphold- For vehicles equipped with third row seating, there are ers, located in the center armrest between the two seats. additional cupholders located in the trim panels. When the armrest is folded flat the cupholders are in the In addition to cupholders, vehicles may also be equipped back of the Head Restraint.
Page 278: Storage
276 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! If containers of hot liquid are placed in the bottle holder, they can spill when the door is closed, burn- ing the occupants. Be careful when closing the doors to avoid injury. STORAGE Glove Compartment The glove compartment is located on the passenger side...
Page 279: Floor Console Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 277 Floor Console Storage Center Console Storage An open storage area, or cubby bin, is located in the floor There is a storage tray and storage compartment located console. under the center console armrest. Floor Console Cubby Bin Center Console Pull upward on the release handle, located on the front of...
Page 280 278 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Center Console Storage Tray Center Console Storage Compartment The storage tray can be slid forward and rearward or WARNING! removed to access the center console storage compart- ment. Do not operate this vehicle with a console compart- ment lid in the open position.
Page 281: Flip 'N Stow Front Passenger Seat Storage - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 279 Sliding Armrest WARNING! The center console armrest can also slide rearward for Do not operate this vehicle with a console compart- easy access to the storage area. ment lid in the open position. Driving with the console compartment lid open may result in injury in a collision.
Page 282: Second-Row Map Pocket And Grocery Retainers - If Equipped
280 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Be certain that the seat cushion is locked securely into position before using the seat. Otherwise, the seat will not provide the proper stability for passen- gers. An improperly latched seat cushion could cause serious injury.
Page 283: In-Floor Storage Bin With Removable Liner
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 281 cans, plus ice, or other items. The removable bin liner allows for easy filling, emptying, and cleaning. To access the bin, position the floor mat aside (if equipped). Pull the door latch release-loop upward to release the latch and then forward to open the bin door.
Page 284: Cargo Area Features
282 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Removable Liner Rechargeable Flashlight CARGO AREA FEATURES To operate the flashlight, push the switch once for high, twice for low, and a third time to return to off. Rechargeable Flashlight — If Equipped The rechargeable LED flashlight stores in its charging station in the left rear quarter trim panel.
Page 285: Cargo Management System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 283 Cargo Management System Five Passenger System Features • A raised load floor that sits on top of a large built-in storage bin. • A tri-fold door built into the load floor that allows easy access to items in the built-in storage bin.
Page 286 284 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Seven Passenger System Features Cargo Tie-Downs • A large built-in storage bin with a hinged hardcover WARNING! located in the floor behind the third-row passenger seats. Cargo tie-downs are not safe anchors for a child seat tether strap.
Page 287 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 285 WARNING! (Continued) handling. To avoid loss of control resulting in per- sonal injury, follow these guidelines for loading your vehicle: • Do not carry loads that exceed the load limits de- scribed on the label attached to the left door or left door center pillar.
Page 288 286 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • To help protect against personal injury, passengers The cover rolls away neatly inside its housing when not should not be seated in the rear cargo area. The rear in use. You can also remove the cover from the vehicle to cargo space is intended for load carrying purposes make more room in the cargo area.
Page 289 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 287 the trim panels. Lower the cover to position the posts into the bottom of the notches and release the handle. Installing Retractable Cargo Area Cover Insert the spring-loaded post on the opposite end of the cover housing into the attachment point on the opposite Positioning Retractable Cargo Area Cover side of the vehicle.
Page 290: Rear Window Features
288 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! A cargo cover that is unsecured in the vehicle could cause injury in a collision. It could become airborne during a sudden stop and strike someone inside the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment.
Page 291 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 289 pump will continue to operate as long as the switch is wiper will resume function at whichever position the held. Upon release, the wiper will cycle three times switch is set at. before returning to the set position. CAUTION! •...
Page 292: Rear Window Defroster
290 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) CAUTION! the blade cannot return to the park position, dam- Failure to follow these cautions can cause damage to age to the rear wiper motor may occur. the heating elements: • Use care when washing the inside of the rear Rear Window Defroster window.
Page 293 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 291 cross rails. In addition, the roof rack does not increase the total load carrying capacity of the vehicle. Be sure the total load of cargo inside the vehicle plus that on the roof rack does not exceed the maximum vehicle load capacity.
Page 294 292 UNDERSTANDING THE FEATURES OF YOUR VEHICLE crossbar and four rearward marks for the rear cross- Check the straps frequently to be sure that the load bar. Make sure the crossbars remain equally spaced or remains securely attached. parallel at any position for proper function. CAUTION! 3.
Page 295 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 293 CAUTION! (Continued) WARNING! 150 lb (68 kg). Always distribute heavy loads as Cargo must be securely tied before driving your evenly as possible and secure the load appropri- vehicle. Improperly secured loads can fly off the ately.
Page 297 UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS ▫ Electronic Vehicle Information Center (EVIC) INSTRUMENT PANEL FEATURES ..298 Displays ......329 INSTRUMENT CLUSTER .
Page 298 296 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Important Notes For Single Video Screen UCONNECT SETTINGS ....336 System ......367 ▫...
Page 299 UNDERSTANDING YOUR INSTRUMENT PANEL 297 ▫ Manual Three Zone Climate Controls With STEERING WHEEL AUDIO CONTROLS ..385 Touchscreen — If Equipped ....388 ▫...
Page 300: Instrument Panel Features
298 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 — Side Window Demist Outlet 6 — Switch Bank 11 — Engine Start/Stop Button 2 — Air Outlet 7 — Uconnect Hard Controls 12 — Hood Release Lever 3 — Instrument Cluster 8 —...
Page 301: Instrument Cluster
UNDERSTANDING YOUR INSTRUMENT PANEL 299 INSTRUMENT CLUSTER Premium Instrument Cluster...
Page 302 300 UNDERSTANDING YOUR INSTRUMENT PANEL 1. Tachometer 5. Temperature Gauge • Indicates the engine speed in revolutions per minute • The temperature gauge shows engine coolant tem- (RPM x 1000). perature. Any reading within the normal range indi- cates that the engine cooling system is operating 2.
Page 303: Warning And Indicator Lights
UNDERSTANDING YOUR INSTRUMENT PANEL 301 WARNING AND INDICATOR LIGHTS CAUTION! (Continued) IMPORTANT: The warning / indicator light switches on remains on the “H”, turn the engine off immediately in the instrument panel together with a dedicated mes- and call an authorized dealer for service. sage and/or acoustic signal when applicable.
Page 304: Red Telltale Indicator Lights
302 UNDERSTANDING YOUR INSTRUMENT PANEL Red Telltale Indicator Lights Seat Belt Reminder Warning Light Red Telltale What It Means Light Seat Belt Reminder Warning Light When the ignition switch is first turned to ON/RUN, this light will turn on for four to eight seconds as a bulb check.
Page 305 UNDERSTANDING YOUR INSTRUMENT PANEL 303 Air Bag Warning Light Red Telltale What It Means Light Air Bag Warning Light This light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to ON/RUN. If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.
Page 306 304 UNDERSTANDING YOUR INSTRUMENT PANEL Brake Warning Light Red Telltale What It Means Light Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake ap- plication. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir.
Page 307 UNDERSTANDING YOUR INSTRUMENT PANEL 305 The light will remain on until the cause is corrected. Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. NOTE: The light may flash momentarily during sharp cornering maneuvers, which change fluid level condi- Operation of the Brake Warning Light can be checked by tions.
Page 308 306 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicle Security Warning Light — If Equipped Red Telltale What It Means Light Vehicle Security Warning Light This light will flash at a fast rate for approximately 15 seconds when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed.
Page 309 UNDERSTANDING YOUR INSTRUMENT PANEL 307 Engine Temperature Warning Light Red Warning What It Means Light Engine Temperature Warning Light This light warns of an overheated engine condition. As engine coolant temperatures rise and the gauge approaches H, this indicator will illuminate and a single chime will sound after reaching a set threshold.
Page 310 308 UNDERSTANDING YOUR INSTRUMENT PANEL Transmission Temperature Warning Light Red Telltale What It Means Light Transmission Temperature Warning Light This light indicates that the transmission fluid temperature is running hot. This may occur with severe usage. If this light turns on, safely pull over and stop them vehicle. Then, shift the trans- mission into NEUTRAL and run the engine at idle or faster until the light turns off.
Page 311 UNDERSTANDING YOUR INSTRUMENT PANEL 309 Charging System Warning Light Red Telltale What It Means Light Charging System Warning Light This light shows the status of the electrical charging system. If the light stays on or comes on while driving, turn off some of the vehicle’s nonessential electrical devices or increase engine speed (if at idle).
Page 312 310 UNDERSTANDING YOUR INSTRUMENT PANEL Oil Pressure Warning Light Red Telltale What It Means Light Oil Pressure Warning Light This light indicates low engine oil pressure. If the light turns on while driving, stop the ve- hicle and shut off the engine as soon as possible. A chime will sound when this light turns Do not operate the vehicle until the cause is corrected.
Page 313 UNDERSTANDING YOUR INSTRUMENT PANEL 311 Electronic Throttle Control (ETC) Warning Light Red Telltale What It Means Light Electronic Throttle Control (ETC) Warning Light This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a problem is detected while the engine is running, the light will either stay on or flash de- pending on the nature of the problem.
Page 314 312 UNDERSTANDING YOUR INSTRUMENT PANEL Electric Power Steering Fail Warning — If Equipped Red Telltale What It Means Light Electric Power Steering Fail Warning This light is used to manage the electrical warning of the EPS (Power Steering System). Re- fer to “Power Steering”...
Page 315 UNDERSTANDING YOUR INSTRUMENT PANEL 313 Liftgate Open Warning Light Red Telltale What It Means Light Liftgate Open Warning Light This indicator will turn when the liftgate is open. NOTE: If the vehicle is moving there will also be a single chime.
Page 316: Yellow Telltale Indicator Lights
314 UNDERSTANDING YOUR INSTRUMENT PANEL Yellow Telltale Indicator Lights Engine Check/Malfunction Indicator Light (MIL) Yellow Telltale What It Means Light Engine Check/Malfunction Indicator Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems. The light will illuminate when the ignition is in the ON position before engine start.
Page 317 UNDERSTANDING YOUR INSTRUMENT PANEL 315 CAUTION! WARNING! Prolonged driving with the Malfunction Indicator A malfunctioning catalytic converter, as referenced Light (MIL) on could cause damage to the engine above, can reach higher temperatures than in normal control system. It also could affect fuel economy and operating conditions.
Page 318 316 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Stability Control (ESC) Indicator Light — If Equipped Yellow Telltale What It Means Light Electronic Stability Control (ESC) Indicator Light The “ESC Indicator Light” in the instrument cluster will come on when the ignition switch is turned to the ON/RUN position.
Page 319 UNDERSTANDING YOUR INSTRUMENT PANEL 317 Electronic Stability Control (ESC) OFF Indicator Light — If Equipped Yellow Telltale What It Means Light Electronic Stability Control (ESC) OFF Indicator Light This light indicates the Electronic Stability Control (ESC) is off. With Drive Modes the ESC OFF indicator will be lit any time the Traction modes is set to Sport, Track or Full OFF.
Page 320 318 UNDERSTANDING YOUR INSTRUMENT PANEL Tire Pressure Monitoring Indicator Light Yellow Telltale What It Means Light Tire Pressure Monitoring Indicator Light The warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recommended value and/or that slow pressure loss is occurring. In these cases, optimal tire duration and fuel consumption may not be guaranteed.
Page 321 UNDERSTANDING YOUR INSTRUMENT PANEL 319 on the vehicle placard or tire inflation pressure label, you Your vehicle has also been equipped with a TPMS should determine the proper tire inflation pressure for malfunction indicator to indicate when the system is not those tires.
Page 322 320 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! CAUTION! (Continued) type, and/or style. Aftermarket wheels can cause The TPMS has been optimized for the original sensor damage. Using aftermarket tire sealants may equipment tires and wheels. TPMS pressures and cause the Tire Pressure Monitoring System (TPMS) warning have been established for the tire size sensor to become inoperable.
Page 323 UNDERSTANDING YOUR INSTRUMENT PANEL 321 Anti-Lock Brake (ABS) Indicator Light Yellow Telltale What It Means Light Anti-Lock Brake (ABS) Indicator Light This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the igni- tion switch is placed in the ON/RUN position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required.
Page 324 322 UNDERSTANDING YOUR INSTRUMENT PANEL Low Fuel Indicator Light Yellow Telltale What It Means Light Low Fuel Indicator Light When the fuel level reaches approximately 3.0 gal (11.0 L) this light will turn on, and remain on until fuel is added. Low Washer Fluid Indicator Light —...
Page 325: Green Telltale Indicator Lights
UNDERSTANDING YOUR INSTRUMENT PANEL 323 Green Telltale Indicator Lights Park/Headlight ON Indicator Light Green Telltale What It Means Light Park/Headlight ON Indicator Light This indicator will illuminate when the park lights or headlights are turned on. Front Fog Indicator Light — If Equipped Green Telltale What It Means Light...
Page 326 324 UNDERSTANDING YOUR INSTRUMENT PANEL Turn Signal Indicator Lights Green Tell- What It Means tale Light Turn Signal Indicator Lights The instrument cluster arrow will flash independently for the LEFT or RIGHT turn signal as se- lected, as well as the exterior turn signal lamp(s) (front and rear) as selected when the multi- function lever is moved down (LEFT) or up (RIGHT).
Page 327: White Telltale Indicator Light
UNDERSTANDING YOUR INSTRUMENT PANEL 325 Electronic Speed Control SET Indicator Light Green Telltale What It Means Light Electronic Speed Control SET Indicator Light This light will turn on when the electronic speed control is SET. Refer to “Electronic Speed Control” in “Understanding The Features Of Your Vehicle” for further information. White Telltale Indicator Light Electronic Speed Control ON Indicator Light White Telltale...
Page 328: Blue Telltale Indicator Light
326 UNDERSTANDING YOUR INSTRUMENT PANEL Blue Telltale Indicator Light High Beam Indicator Light Blue Telltale What It Means Light High Beam Indicator Light This indicator shows that the high beam headlights are on. Push the multifunction control lever away from you to switch the headlights to high beam. Pull the lever toward you to switch the headlights back to low beam.
Page 329: Electronic Vehicle Information Center (Evic)
UNDERSTANDING YOUR INSTRUMENT PANEL 327 ELECTRONIC VEHICLE INFORMATION CENTER This system allows the driver to select a variety of useful (EVIC) information by pushing the switches mounted on the steering wheel. The EVIC consists of the following: The Electronic Vehicle Information Center (EVIC) fea- •...
Page 330 328 UNDERSTANDING YOUR INSTRUMENT PANEL • DOWN Arrow Button The system allows the driver to select information by pushing the following buttons mounted on the steering Push and release the DOWN button to scroll wheel: downward through the main menus and submenus.
Page 331: Electronic Vehicle Information Center (Evic) Displays
UNDERSTANDING YOUR INSTRUMENT PANEL 329 • Five Second Stored Messages Electronic Vehicle Information Center (EVIC) Displays When the appropriate conditions occur, this type of The EVIC display consists of three sections: message takes control of the main display area for five seconds and then returns to the previous screen.
Page 332 330 UNDERSTANDING YOUR INSTRUMENT PANEL • Unstored Messages Until RUN When the appropriate conditions exist, the EVIC displays the following messages: These messages deal primarily with the Remote Start • Remote Start aborted — Door ajar feature. This message type is displayed until the ignition is in the RUN state.
Page 333: Oil Change Due
UNDERSTANDING YOUR INSTRUMENT PANEL 331 • Turn Signal On (with a continuous warning chime if • Channel # Transmit the vehicle is driven more than 1 mile [1.6 km] with • Channel # Training either turn signal on) • Channel # Trained •...
Page 334: Fuel Economy
332 UNDERSTANDING YOUR INSTRUMENT PANEL system is duty cycle based, which means the engine oil NOTE: If the indicator message illuminates when you change interval may fluctuate dependent upon your start the vehicle, the oil change indicator system did not personal driving style.
Page 335 UNDERSTANDING YOUR INSTRUMENT PANEL 333 show dashes for two seconds. Then, the history informa- determined by a weighted average of the instantaneous tion will be erased, and the averaging will continue from and average fuel economy, according to the current fuel the last fuel average reading before the reset.
Page 336: Vehicle Speed
334 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicle Speed selected feature to reset individually. The three features can only be reset individually. The following Trip func- Push and release the UP or DOWN button until “Vehicle tions display in the EVIC: Speed” displays highlighted in the EVIC. Push the •...
Page 337: Tire Pressure
UNDERSTANDING YOUR INSTRUMENT PANEL 335 Trip B the RIGHT button to view a graphic of the vehicle with a tire pressure value at each corner of the graphic. • Shows the total distance traveled for Trip B since the last reset. Vehicle Info (Customer Information Features) •...
Page 338: Messages
336 UNDERSTANDING YOUR INSTRUMENT PANEL • Engine Hours UCONNECT SETTINGS The Uconnect system uses a combination of buttons on Displays the number of hours of engine operation. the touchscreen and buttons on the faceplate located on Messages the center of the instrument panel that allows you to Push and release the UP or DOWN button until “Mes- access and change the customer programmable features.
Page 339: Buttons On The Touchscreen
UNDERSTANDING YOUR INSTRUMENT PANEL 337 Buttons On The Touchscreen Buttons on the touchscreen are accessible on the Uconnect Touchscreen. CAUTION! Do not attach any object to touchscreen, doing so can result in damage to the touchscreen. Customer Programmable Features — Uconnect 4.3 Settings In this mode the Uconnect system allows you to access 1 —...
Page 340 338 UNDERSTANDING YOUR INSTRUMENT PANEL setting buttons on the touchscreen or by selecting any point on the scale between the “+” and “–” buttons on the touchscreen. Then press the back arrow button on the touchscreen. • Mode Press the “Mode” button on the touchscreen to change this display.
Page 341 UNDERSTANDING YOUR INSTRUMENT PANEL 339 • Touchscreen Beep the language preferred. Then press the back arrow button on the touchscreen. As you continue, the information will Press the “Touchscreen Beep” button on the touchscreen display in the selected language. to turn on or shut off the sound heard when a button on •...
Page 342 340 UNDERSTANDING YOUR INSTRUMENT PANEL • Show Time Status Safety & Driving Assistance • Park Assist — If Equipped Press the “Show Time Status” button on the touchscreen to change this display. When in this display, you may Press the “Park Assist” button on the touchscreen to turn on or shut off the digital clock in the status bar.
Page 343 UNDERSTANDING YOUR INSTRUMENT PANEL 341 • Headlights With Wipers Brake Control System” in “Starting And Operating” for system function and operating information. To make Press the “Headlights With Wipers” button on the touch- your selection, press the “Hill Start Assist” button on the screen to change this display.
Page 344 342 UNDERSTANDING YOUR INSTRUMENT PANEL touchscreen. Refer to “Automatic Headlights — If the “Steering Directed Lights” button on the touchscreen Equipped” in “Understanding The Features Of Your and select “ON” or ‘OFF.” Then press the back arrow Vehicle” for further information. button on the touchscreen.
Page 345 UNDERSTANDING YOUR INSTRUMENT PANEL 343 • Flash Lamps With Lock Doors & Locks • Auto Unlock On Exit Press the “Flash Lamps With Lock” button on the touch- screen to change this display. When this feature is se- Press the “Auto Unlock On Exit” button on the touch- lected, the exterior lamps will flash when the doors are screen to change this display.
Page 346 344 UNDERSTANDING YOUR INSTRUMENT PANEL • Sounds Horn With Lock passenger’s doors. When Unlock All Doors On 1st Press is selected, all of the doors will unlock on the first press Press the “Sounds Horn With Lock” button on the of the RKE transmitter UNLOCK button.
Page 347 UNDERSTANDING YOUR INSTRUMENT PANEL 345 • Passive Entry (Keyless Enter-N-Go) — If Equipped Seats” button on the touchscreen and select “ON” or “OFF.” Then press the back arrow button on the touch- Press the “Passive Entry” button on the touchscreen to screen.
Page 348 346 UNDERSTANDING YOUR INSTRUMENT PANEL equipped), power sunroof (if equipped), and power NOTE: Keep magnetic materials away from the top of the outlets will remain active for up to 10 minutes after the instrument panel, such as iPod’s, Mobile Phones, Lap- ignition is cycled to OFF.
Page 349 UNDERSTANDING YOUR INSTRUMENT PANEL 347 • Calibration Audio • Equalizer Press the “Calibration” button on the touchscreen to change this setting. This compass is self-calibrating, Press the “Equalizer” button on the touchscreen to which eliminates the need to manually reset the compass. change this display.
Page 350 348 UNDERSTANDING YOUR INSTRUMENT PANEL • Speed Adjusted Volume “Surround Sound” button on the touchscreen and select “ON” or “OFF.” Then press the back arrow button on the Press the “Speed Adjusted Volume” button on the touch- touchscreen. screen to change this display. This feature increases or decreases volume relative to vehicle speed.
Page 351: Customer Programmable Features - Uconnect System 8.4 Settings
UNDERSTANDING YOUR INSTRUMENT PANEL 349 • Subscription Info Customer Programmable Features — Uconnect System 8.4 Settings New vehicle purchasers or lessees will receive a free Press the “More” button on the touchscreen, then press limited time subscription to SIRIUS Satellite Radio with the “Settings”...
Page 352 350 UNDERSTANDING YOUR INSTRUMENT PANEL • Display Brightness With Headlights ON Once the setting is complete press the Back Arrow button on the touchscreen to return to the previous menu or When in this display, you may select the brightness with press the “X”...
Page 353 UNDERSTANDING YOUR INSTRUMENT PANEL 351 functions and the navigation system (if equipped). Press Length, press the “Brief” or “Detailed” button on the the “Set Language” button on the touchscreen and then touchscreen until a check-mark appears next to the press the desired language button on the touchscreen setting, showing that setting has been selected.
Page 354 352 UNDERSTANDING YOUR INSTRUMENT PANEL • Sync With GPS Time — If Equipped Cluster” button on the touchscreen, until a check-mark appears next to the setting, showing that setting has been When in this display, you may automatically have the selected.
Page 355 UNDERSTANDING YOUR INSTRUMENT PANEL 353 • Set Time Minutes • Show Time In Status Bar — If Equipped When in this display, you may adjust the minutes. The When in this display, you may turn on or shut off the “Sync with GPS Time”...
Page 356 354 UNDERSTANDING YOUR INSTRUMENT PANEL Assist status, press and release the “OFF,” “Sound Only” setting, showing that setting has been selected. Press the or “Sounds and Display” button. Then press the back back arrow button on the touchscreen to return to the arrow button on the touchscreen.
Page 357 UNDERSTANDING YOUR INSTRUMENT PANEL 355 • Headlights Off Delay • Headlights With Wipers — If Equipped When this feature is selected, it allows the adjustment of When this feature is selected, and the headlight switch is the amount of time the headlights remain on after the in the AUTO position, the headlights will turn on ap- engine is shut off.
Page 358 356 UNDERSTANDING YOUR INSTRUMENT PANEL to the previous menu. Refer to “Automatic Headlights — to setting, showing that setting has been selected. Press If Equipped” in “Understanding The Features Of Your the back arrow button on the touchscreen to return to the Vehicle”...
Page 359 UNDERSTANDING YOUR INSTRUMENT PANEL 357 • Auto Unlock On Exit • Flash Headlights With Lock When this feature is selected, all doors will unlock when When this feature is selected, the signal lights will flash the vehicle is stopped and the transmission is in the when the doors are locked with the Remote Keyless PARK or NEUTRAL position and the driver’s door is Entry (RKE) transmitter.
Page 360 358 UNDERSTANDING YOUR INSTRUMENT PANEL • Sound Horn With Remote Start NOTE: If the vehicle is programmed to Unlock All Doors 1st Press, all doors will unlock no matter which Passive When this feature is selected, the horn will sound when Entry equipped door handle is grasped.
Page 361 UNDERSTANDING YOUR INSTRUMENT PANEL 359 • Auto-On Driver Heated Seat With Vehicle Start — If arrow button on the touchscreen to return to the previous menu. Refer to “Keyless Enter-N-Go” in “Things To Equipped Know Before Starting Your Vehicle.” When this feature is selected the driver’s heated seat will Auto-On Comfort &...
Page 362 360 UNDERSTANDING YOUR INSTRUMENT PANEL • Variance after the ignition is cycled to OFF. Opening either front door will cancel this feature. To change the Engine Off Compass Variance is the difference between Magnetic Power Delay status press the “0 seconds,” “45 seconds, North and Geographic North.
Page 363 UNDERSTANDING YOUR INSTRUMENT PANEL 361 the compass by pressing the “ON” button on the touch- screen and completing one or more 360-degree turns (in an area free from large metal or metallic objects) until the CAL indicator displayed in the EVIC turns off. The compass will now function normally.
Page 364 362 UNDERSTANDING YOUR INSTRUMENT PANEL point on the scale between the “+” and “–” buttons on the Phone/Bluetooth touchscreen. Then press the back arrow button on the After pressing the “Phone/Bluetooth” button on the touchscreen. touchscreen the following settings will be available. NOTE: Bass/Mid/Treble allow you to simply slide your •...
Page 365: Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 363 touchscreen, select the channels you would like to skip UCONNECT MULTIMEDIA — VIDEO followed by pressing the back arrow button on the ENTERTAINMENT SYSTEM (VES) — IF EQUIPPED touchscreen. Your rear seat Video Entertainment System (VES) is •...
Page 366: Single Video Screen
364 UNDERSTANDING YOUR INSTRUMENT PANEL • When the Video Screen is open and a DVD is inserted into the radio, the screen turns on automatically, the headphone transmitters turn on and playback begins. Single Video Screen NOTE: Typically there are two different ways to operate the features of the Video Entertainment System (VES).
Page 367: Play Video Games
UNDERSTANDING YOUR INSTRUMENT PANEL 365 3. Ensure the VES Remote Control and the Headphone Play Video Games switch is on Channel 1. Connect the video game console to the Auxiliary RCA input jacks located on the back of the center console. Using The Remote Control Audio/Video RCA Jacks (AUX Jacks) 1.
Page 368: Listen To An Audio Source On Channel 2 While A Video Is Playing On Channel 1
366 UNDERSTANDING YOUR INSTRUMENT PANEL When connecting an external source to the AUX input, be Using The Touchscreen Radio Controls sure to follow the standard color coding for the VES 1. Press the “MORE” button on the touchscreen. jacks: 2. Press the “Rear Entertainment” button on the touch- NOTE: Certain high-end video games, such as Playsta- screen to display the Rear Entertainment Controls.
Page 369: Important Notes For Single Video Screen System
UNDERSTANDING YOUR INSTRUMENT PANEL 367 Using The Remote Control 4. Press the “1” or “2” button on the touchscreen for the channel desired and press the “Source” button on the 1. Push the MODE button on the Remote Control and the touchscreen to select the desired mode.
Page 370: Play A Dvd Using The Touchscreen Radio
368 UNDERSTANDING YOUR INSTRUMENT PANEL Play A DVD Using The Touchscreen Radio be stopped, and the shift lever must be in the PARK position for vehicles with automatic transmission. In 1. Insert the DVD with the label facing up. The radio vehicles with manual transmission the parking brake automatically selects the appropriate mode after the must be engaged even when the vehicle is parked.
Page 371: Ves Remote Control - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 369 VES Remote Control — If Equipped audio while the screen is closed, push the Power button to turn the headphone transmitter on. 2. Channel Selector Indicators – When a button is pushed, the currently affected channel or channel button is illuminated momentarily.
Page 372 370 UNDERSTANDING YOUR INSTRUMENT PANEL – In radio modes, push to seek the next tunable 10. PROG Up/Down – When listening to a radio mode, station. In disc modes, push and hold to fast forward pushing PROG Up selects the next preset and push- through the current audio track or video chapter.
Page 373: Remote Control Storage
UNDERSTANDING YOUR INSTRUMENT PANEL 371 selected and the disc is stopped, push the SETUP Remote Control Storage button to access the DVD Setup menu. (see the DVD The video screen(s) come with a built in storage compart- Setup Menu of this manual.) ment for the remote control which is accessible when the screen is opened.
Page 374: Locking The Remote Control
372 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Press the “Rear Entertainment” button on the touch- screen to display the Rear Entertainment Controls. 3. Press the “Lock-out” button on the touchscreen to lock the remote control. Pressing the “Lock-out” button on the touchscreen a second time will unlock the remote control.
Page 375: Ves Headphones Operation
UNDERSTANDING YOUR INSTRUMENT PANEL 373 3. Replace the battery compartment cover. VES Headphones Operation The headphones receive two separate channels of audio using an infrared transmitter from the video screen. If no audio is heard after increasing the volume control, verify that the screen is turned on and in the down position and that the channel is not muted and the headphone channel selector switch is on the desired...
Page 376: Replacing The Headphone Batteries
374 UNDERSTANDING YOUR INSTRUMENT PANEL Replacing The Headphone Batteries NOTE: The rear video system must be turned on before sound can be heard from the headphones. To conserve Each set of headphones requires two AAA batteries for battery life, the headphones will automatically turn off operation.
Page 377: Unwired Stereo Headphone Lifetime Limited Warranty
UNDERSTANDING YOUR INSTRUMENT PANEL 375 3. If the video screen is displaying a video source (such particular Unwired Technology LLC ( Unwired ) wireless as a DVD Video), pushing STATUS shows the status headphone ( Product ). The warranty is not transferable. on a popup banner at the bottom of the screen.
Page 378 376 UNDERSTANDING YOUR INSTRUMENT PANEL INCIDENTAL, CONSEQUENTIAL, EXEMPLARY, PU- EXCLUSIVE REMEDY REGARDING DEFECTIVE NITIVE OR OTHER DAMAGES OF ANY KIND OR PRODUCTS, AND IS IN LIEU OF ALL OTHER WAR- NATURE WHATSOEVER. Some states and jurisdictions RANTIES (EXPRESS OR IMPLIED), INCLUDING ANY may not allow the exclusion or limitation of incidental or WARRANTY OR MERCHANTABILITY OR FITNESS consequential damages, so the above limitation may not...
Page 379: System Information
UNDERSTANDING YOUR INSTRUMENT PANEL 377 System Information to the items called out by number, the remaining infor- mation displays the current status of the source (such as Information Mode Display station frequency, name, preset or track number, song title, artist name, album name, etc.). 1.
Page 380 378 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Channel 2 Mode — Displays the current source for Numeric Keypad Menu Channel 2. 5. Remote Locked Out — When the icon is displayed, the remote control functions are disabled. 6. Clock — Displays the time. 7.
Page 381 UNDERSTANDING YOUR INSTRUMENT PANEL 379 1. Push the remote control’s navigation buttons ( , , , Disc Menu ) to navigate to the desired digit. When listening to a CD Audio or CD Data disc, pushing the remote control’s MENU button displays a list of all 2.
Page 382 380 UNDERSTANDING YOUR INSTRUMENT PANEL on the screen. The factory default settings are already set for optimum viewing, so there is no need to change these settings under normal circumstances. To change the settings, push the remote control’s naviga- tion buttons to select an item, then push the remote control’s navigation buttons to change the value for the currently selected item.
Page 383 UNDERSTANDING YOUR INSTRUMENT PANEL 381 • CD Data discs with MP3 and WMA compressed audio 3. To change the current audio mode, push the remote control’s MODE button. This will automatically select format files the next available audio mode without using the •...
Page 384 382 UNDERSTANDING YOUR INSTRUMENT PANEL • For multi-session CDs that contain only multiple CD- increase the volume level to account for this change in level, remember to lower the volume before changing the Audio sessions, the player will renumber the tracks so disc or to another mode.
Page 385 UNDERSTANDING YOUR INSTRUMENT PANEL 383 The recommended method for labeling recordable discs “.m4a”. To prevent incorrect playback, do not use (CD-R, CD-RW, DVD-R and DVD-RW) is with a perma- these extensions for any other types of files. nent marker. Do not use adhesive labels as they may •...
Page 386 384 UNDERSTANDING YOUR INSTRUMENT PANEL between 64 and 192Kbps. Variable bit rates are also If a disc has a damaged track which results in audible or supported. For both formats, the recommended visible errors that persists for 2.0 seconds, the DVD sample rate is either 44.1kHz or 48kHz.
Page 387: Ipod/Usb/Mp3 Control
UNDERSTANDING YOUR INSTRUMENT PANEL 385 technology must be authorized by Macrovision, and is iPod control supports Mini, 4G, Photo, Nano, 5G iPod intended for home or other limited viewing uses other- and iPhone devices. Some iPod software versions may wise authorized by Macrovision. Reverse engineering or not fully support the iPod control features.
Page 388: Right-Hand Switch Functions
386 UNDERSTANDING YOUR INSTRUMENT PANEL Left-Hand Switch Functions For Radio Operation • Push the top of the switch to SEEK the next listenable station up from the current setting. • Push the bottom of the switch to SEEK the next listenable station down from the current setting.
Page 389: Cd/Dvd Disc Maintenance
UNDERSTANDING YOUR INSTRUMENT PANEL 387 • Push the switch up or down twice to listen to the 4. Do not use solvents such as benzene, thinner, cleaners, second track, three times to listen to the third track, or anti-static sprays. and so forth.
Page 390: Climate Controls
388 UNDERSTANDING YOUR INSTRUMENT PANEL not harmful to the radio. If your radio performance does Manual Three Zone Climate Controls With not satisfactorily “clear” by the repositioning of the Touchscreen — If Equipped antenna, it is recommended that the radio volume be Buttons On The Faceplate turned down or off during mobile device operation when Buttons on the faceplate are located on the left and right...
Page 391 UNDERSTANDING YOUR INSTRUMENT PANEL 389 Uconnect 4.3 Manual with Touchscreen Climate Button Manual Temperature Controls — Buttons On The On The Faceplate Faceplate Buttons On The Touchscreen Buttons on the touchscreen are accessible on the Uconnect system screen.
Page 392 390 UNDERSTANDING YOUR INSTRUMENT PANEL Uconnect 4.3 Manual 3 — Zone Temperature Controls — Uconnect 8.4 Manual 3 — Zone Temperature Controls — Buttons On The Touchscreen Buttons On The Touchscreen...
Page 393 UNDERSTANDING YOUR INSTRUMENT PANEL 391 Button Descriptions (Applies To Both Buttons On The 4. Front Defrost Button Faceplate And Buttons On The Touchscreen) Press and release to change the current airflow setting to 1. MAX A/C Button Defrost mode. The indicator illuminates when this fea- ture is ON.
Page 394 392 UNDERSTANDING YOUR INSTRUMENT PANEL 6. Rear Climate Button — If Equipped CAUTION! Press and release this button to turn on the rear climate Failure to follow these cautions can cause damage to controls. The indicator will illuminate when the rear the heating elements: climate controls are ON.
Page 395 UNDERSTANDING YOUR INSTRUMENT PANEL 393 NOTE: Pressing this button while in Sync mode will Blower Control Knob On The Faceplate automatically exit Sync. The blower speed increases as you turn the blower control knob clockwise from the lowest blower setting. 9.
Page 396 394 UNDERSTANDING YOUR INSTRUMENT PANEL • Panel Mode • Floor Mode Air comes from the outlets in the instrument Air comes from the floor outlets. A slight panel. Each of these outlets can be individu- amount of air is directed through the defrost ally adjusted to direct the flow of air.
Page 397 UNDERSTANDING YOUR INSTRUMENT PANEL 395 NOTE: In Sync mode, this button will also automatically temperatures. Driver and passenger have independent adjust the passenger temperature setting at the same temperature control if Sync mode is not illuminated. time. Climate Control Functions 14.
Page 398 396 UNDERSTANDING YOUR INSTRUMENT PANEL • If fog or mist appears on the windshield or side glass, In MAX A/C, the blower level and mode position can be select Defrost mode and adjust blower speed if adjusted to desired user settings. Pressing other settings needed.
Page 399: Rear Manual Temperature Control (Mtc) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 397 NOTE: In cold weather, use of Recirculation mode may Rear Manual Temperature Control (MTC) — If lead to excessive window fogging. The recirculation Equipped feature may be unavailable (soft button greyed out) if The rear MTC system has floor air outlets at the rear right conditions exist that could create fogging on the inside of side of the 3rd Row seats and overhead outlets at each the windshield.
Page 400 398 UNDERSTANDING YOUR INSTRUMENT PANEL Uconnect 4.3 Manual Rear Climate Buttons On The Uconnect 8.4 Manual Rear Climate Button On The Touchscreen Controls Screen Touchscreen Controls Screen 1 — Blower Up Button 5 — Done Button 1 — Rear Lock Button 5 —...
Page 401 UNDERSTANDING YOUR INSTRUMENT PANEL 399 Controlling The Rear Climate Controls From The a lock symbol in the rear display. The rear temperature Front Uconnect Touchscreen and air source are controlled from the front Uconnect system. The Three-Zone climate control system allows for adjust- •...
Page 402 400 UNDERSTANDING YOUR INSTRUMENT PANEL to high. This allows the rear seat occupants to control the volume of air circulated in the rear of the vehicle. CAUTION! Interior air enters the Rear Automatic Temperature Control System through an intake grille, located in the right side trim panel.
Page 403: Automatic Three Zone Temperature Control (Atc) With Touchscreen - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 401 When rear controls are locked by the Uconnect system, Floor Mode the Rear Temperature Lock symbol on the temperature Air comes from the floor outlets. knob is illuminated and any rear overhead adjustments are ignored. Automatic Three Zone Temperature Control (ATC) With Touchscreen —...
Page 404 402 UNDERSTANDING YOUR INSTRUMENT PANEL Uconnect 4.3 Automatic Climate Button On The Automatic Temperature Controls — Buttons On The Faceplate Faceplate Buttons On The Touchscreen Buttons On The Touchscreen are accessible on the Uconnect system screen.
Page 405 UNDERSTANDING YOUR INSTRUMENT PANEL 403 Uconnect 4.3 Automatic 3 — Zone Temperature Controls Uconnect 8.4 Automatic 3 — Zone Temperature Controls — Buttons On The Touchscreen — Buttons On The Touchscreen...
Page 406 404 UNDERSTANDING YOUR INSTRUMENT PANEL Button Descriptions (Applies To Both Buttons On The 4. AUTO Operation Button Faceplate And Buttons On The Touchscreen) Automatically controls the interior cabin temperature by 1. MAX A/C Button adjusting airflow distribution and amount. Performing this function will cause the ATC to switch between Press and release to change the current setting, the manual mode and automatic modes.
Page 407 UNDERSTANDING YOUR INSTRUMENT PANEL 405 6. Rear Defrost Button CAUTION! (Continued) Press and release this button to turn on the rear window • Do not use scrapers, sharp instruments, or abrasive defroster and the heated outside mirrors (if equipped). window cleaners on the interior surface of the An indicator will illuminate when the rear window window.
Page 408 406 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Pressing this button while in Sync mode will 11. Blower Control automatically exit Sync. Blower control is used to regulate the amount of air forced 9. Passenger Temperature Control Down Button through the climate system. There are seven blower speeds (Uconnect 8.4) available.
Page 409 UNDERSTANDING YOUR INSTRUMENT PANEL 407 12. Modes NOTE: BI-LEVEL mode is designed under comfort con- ditions to provide cooler air out of the panel outlets and The airflow distribution mode can be adjusted so air warmer air from the floor outlets. comes from the instrument panel outlets, floor outlets •...
Page 410 408 UNDERSTANDING YOUR INSTRUMENT PANEL 14. Driver Temperature Control Down Button (Uconnect the passenger compartment. Moving the temperature bar 8.4) into the red area, indicates warmer temperatures. Mov- ing the temperature bar into the blue area indicates cooler Provides the driver with independent temperature con- temperatures.
Page 411 UNDERSTANDING YOUR INSTRUMENT PANEL 409 NOTE: If fog or mist appears on the windshield or side Recirculation Control glass, select Defrost mode and adjust blower speed if needed. When outside air contains smoke, odors, or high humidity, or if rapid cooling is desired, MAX A/C you may wish to recirculate interior air by MAX A/C sets the control for maximum cooling perfor-...
Page 412 410 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: In cold weather, use of Recirculation mode may 2. Next, adjust the temperature you would like the lead to excessive window fogging. The recirculation system to maintain by adjusting the driver and pas- feature may be unavailable (soft button greyed out) if senger temperature buttons on the touchscreen or conditions exist that could create fogging on the inside of buttons on the faceplate.
Page 413: Rear Automatic Temperature Control (Atc) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 411 • The temperature can be displayed in U.S. or Metric The operator can also select the direction of the airflow units by selecting the US/M customer-programmable by selecting one of the available mode settings. A/C feature.
Page 414 412 UNDERSTANDING YOUR INSTRUMENT PANEL Uconnect 4.3 Automatic Rear Climate Buttons On The Uconnect 8.4 Automatic Rear Climate Buttons On The Touchscreen Touchscreen 1 — Blower Up Button 5 — Done Button 1 — Rear Auto Button 6 — Blower Up Button 2 —...
Page 415 UNDERSTANDING YOUR INSTRUMENT PANEL 413 Controlling The Rear Climate Controls From The Rear second row occupants can only adjust the rear ATC Front ATC Panel control when the Rear Temperature Lock button is turned off. The Three-Zone ATC system allows for adjustment of the rear climate controls from the front ATC panel.
Page 416 414 UNDERSTANDING YOUR INSTRUMENT PANEL level, it is not necessary to change the settings. You will experience the greatest efficiency by simply allowing the system to function automatically. NOTE: It is not necessary to move the temperature settings for cold or hot vehicles. The system automati- cally adjusts the temperature, mode and fan speed to provide comfort as quickly as possible.
Page 417 UNDERSTANDING YOUR INSTRUMENT PANEL 415 to high. This allows the rear seat occupants to control the the temperature, and clockwise to increase the tempera- volume of air circulated in the rear of the vehicle. ture. The rear temperature settings are displayed in the Uconnect system.
Page 418 416 UNDERSTANDING YOUR INSTRUMENT PANEL Bi-Level Mode A solution of 50% OAT (Organic Additive Technology) coolant that meets the requirements of FCA Material Air comes from both the headliner outlets and the Standard MS.90032 and 50% water is recommended. floor outlets. Refer to “Maintenance Procedures”...
Page 419 UNDERSTANDING YOUR INSTRUMENT PANEL 417 Window Fogging Outside Air Intake Interior fogging on the windshield can be quickly re- Make sure the air intake, located directly in front of the moved by turning the mode selector to Defrost. The windshield, is free of obstructions such as leaves. Leaves Defrost/Floor mode can be used to maintain a clear collected in the air intake may reduce airflow, and if they windshield and provide sufficient heating.
Page 420 418 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Control Setting Suggestions For Various Weather Conditions...
Page 421 STARTING AND OPERATING CONTENTS ▫ Key Ignition Park Interlock....431 STARTING PROCEDURES ....424 ▫...
Page 422 420 STARTING AND OPERATING ▫ Traction ......442 ▫ Brake Assist System (BAS) ....453 ▫...
Page 423 STARTING AND OPERATING 421 ▫ Tire Pressure ......475 TIRE PRESSURE MONITOR SYSTEM (TPMS) . .490 ▫ Tire Inflation Pressures ....476 ▫...
Page 424 422 STARTING AND OPERATING ▫ E-85 General Information ....502 ▫ Vehicle Certification Label ....508 ▫...
Page 425 STARTING AND OPERATING 423 ▫ Towing This Vehicle Behind Another RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) ....523 Vehicle ......523...
Page 426: Starting Procedures
424 STARTING AND OPERATING STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust the fatally injured. Children should be warned not to inside and outside mirrors, fasten your seat belt, and if touch the parking brake, brake pedal or the gear present, instruct all other occupants to buckle their seat selector.
Page 427: Keyless Enter-N-Go
STARTING AND OPERATING 425 Keyless Enter-N-Go CAUTION! Damage to the transmission may occur if the follow- This feature allows the driver to oper- ing precautions are not observed: ate the ignition switch with the push • Do not shift from REVERSE, PARK, or NEUTRAL of a button, as long as the Remote into any forward gear when the engine is above Start/Keyless Enter-N-Go Key Fob is...
Page 428 426 STARTING AND OPERATING 4. If you wish to stop the cranking of the engine prior to position. If the shift lever/gear selector is not in PARK the engine starting, push the button again. and the ENGINE START/STOP button is pushed once, the EVIC (if equipped) will display a “Vehicle NOTE: Normal starting of either a cold or a warm engine Not In Park”...
Page 429: Extreme Cold Weather (Below -22°F Or −30°C)
STARTING AND OPERATING 427 and START. To change the ignition positions without Extreme Cold Weather (Below –22°F Or −30°C) starting the vehicle and use the accessories follow these To ensure reliable starting at these temperatures, use of steps: an externally powered electric engine block heater (avail- •...
Page 430 428 STARTING AND OPERATING Clearing A Flooded Engine (Using ENGINE WARNING! (Continued) START/STOP Button) • Do not attempt to push or tow your vehicle to get it If the engine fails to start after you have followed the started. Vehicles equipped with an automatic trans- “Normal Starting”...
Page 431: After Starting
STARTING AND OPERATING 429 After Starting WARNING! The idle speed is controlled automatically and it will Remember to disconnect the engine block heater decrease as the engine warms up. cord before driving. Damage to the 110-115 Volt electrical cord could cause electrocution. ENGINE BLOCK HEATER —...
Page 432 430 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Unintended movement of a vehicle could injure • Never leave children alone in a vehicle, or with those in or near the vehicle. As with all vehicles, access to an unlocked vehicle. Allowing children to you should never exit a vehicle while the engine is be in a vehicle unattended is dangerous for a running.
Page 433: Key Ignition Park Interlock
STARTING AND OPERATING 431 before the engine can be turned OFF. This helps the CAUTION! driver avoid inadvertently leaving the vehicle without placing the transmission in PARK. Damage to the transmission may occur if the follow- ing precautions are not observed: This system also locks the transmission in PARK when- •...
Page 434 432 STARTING AND OPERATING out of PARK (refer to “Brake/Transmission Shift Inter- (-/+) position (below the Drive position) activates lock System” in this section). To drive, move the shift Autostick mode, providing manual shift control and lever from PARK or NEUTRAL to the DRIVE position. displaying the current gear in the instrument cluster.
Page 435: Gear Ranges
STARTING AND OPERATING 433 Gear Ranges the transmission locking mechanism may make it diffi- cult to move the shift lever out of PARK. As an added DO NOT race the engine when shifting from PARK or precaution, turn the front wheels toward the curb on a NEUTRAL into another gear range.
Page 436 434 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • It is dangerous to shift out of PARK or NEUTRAL or the manual transmission into REVERSE. Always if the engine speed is higher than idle speed. If make sure the keyless ignition node is in the “OFF” your foot is not firmly pressing the brake pedal, the mode, remove the Key Fob from the vehicle and vehicle could accelerate quickly forward or in re-...
Page 437 STARTING AND OPERATING 435 • When shifting into PARK, firmly move the shift lever WARNING! (Continued) all the way forward and to the left until it stops and is leave the ignition in the ACC or ON/RUN mode. A fully seated. child could operate power windows, other controls, •...
Page 438 436 STARTING AND OPERATING DRIVE (D) WARNING! This range should be used for most city and highway Do not coast in NEUTRAL and never turn off the driving. It provides the smoothest upshifts and down- ignition to coast down a hill. These are unsafe shifts, and the best fuel economy.
Page 439 STARTING AND OPERATING 437 transmission shift schedule and expand the range of Transmission Limp Home Mode torque converter clutch engagement. This is done to Transmission function is monitored electronically for prevent transmission damage due to overheating. abnormal conditions. If a condition is detected that could result in transmission damage, Transmission Limp Home During cold temperatures, transmission operation may Mode is activated.
Page 440 438 STARTING AND OPERATING 3. Turn the ignition switch to the OFF position. Overdrive Operation The automatic transmission includes an electronically 4. Wait approximately 10 seconds. controlled Overdrive (top gear). The transmission will 5. Restart the engine. automatically shift into Overdrive if the following con- ditions are present: 6.
Page 441: Autostick
STARTING AND OPERATING 439 A clutch within the torque converter engages automati- braking, eliminate undesirable upshifts and downshifts, cally at calibrated speeds. This may result in a slightly and improve overall vehicle performance. This system different feeling or response during normal operation in can also provide you with more control during passing, the upper gears.
Page 442 440 STARTING AND OPERATING • The transmission will automatically upshift when nec- • Transmission shifting will be more noticeable when essary to prevent engine over-speed. AutoStick is engaged. • The transmission will automatically downshift as the • The system may revert to automatic shift mode if a vehicle slows (to prevent engine lugging) and will fault or overheat condition is detected.
Page 443: All Wheel Drive (Awd) - If Equipped
STARTING AND OPERATING 441 ALL WHEEL DRIVE (AWD) — IF EQUIPPED CAUTION! This feature provides on-demand All-Wheel Drive All wheels must have the same size and type tires. (AWD). The system is automatic with no driver inputs or Unequal tire sizes must not be used. Unequal tire additional driving skills required.
Page 444: Traction
442 STARTING AND OPERATING 2. Slow down if the road has standing water or puddles. WARNING! 3. Replace the tires when tread wear indicators first Rapid acceleration on slippery surfaces is dangerous. become visible. Unequal traction can cause sudden pulling of the 4.
Page 445: Flowing/Rising Water
STARTING AND OPERATING 443 Flowing/Rising Water WARNING! • Driving through standing water limits your vehi- WARNING! cle’s traction capabilities. Do not exceed 5 mph Do not drive on or across a road or path where water (8 km/h) when driving through standing water. is flowing and/or rising (as in storm run-off).
Page 446: Power Steering
444 STARTING AND OPERATING CAUTION! (Continued) CAUTION! (Continued) damage is not covered by the New Vehicle Limited standing water that is deeper than the bottom of Warranty. the tire rims mounted on the vehicle. • Determine the condition of the road or the path •...
Page 447: Power Steering Fluid Check
STARTING AND OPERATING 445 Programmable Features” within “Uconnect Settings” in NOTE: “Understanding Your Instrument Panel” for further • Even if the power steering assistance is no longer information. operational, it is still possible to steer the vehicle. Under these conditions there will be a substantial WARNING! increase in steering effort, especially at low speeds and during parking maneuvers.
Page 448: Parking Brake
446 STARTING AND OPERATING PARKING BRAKE WARNING! Before leaving the vehicle, make sure that the parking Fluid level should be checked on a level surface and brake is fully applied. Also, be certain to leave the with the engine off to prevent injury from moving transmission in PARK.
Page 449 STARTING AND OPERATING 447 NOTE: • When the parking brake is applied and the transmis- sion is placed in gear, the “Brake Warning Light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle.
Page 450 448 STARTING AND OPERATING WARNING! WARNING! (Continued) • Be sure the parking brake is fully disengaged • Never use the PARK position as a substitute for the before driving; failure to do so can lead to brake parking brake. Always apply the parking brake failure and a collision.
Page 451: Brake System
STARTING AND OPERATING 449 BRAKE SYSTEM WARNING! • Riding the brakes can lead to brake failure and Your vehicle is equipped with dual hydraulic possibly a collision. Driving with your foot resting brake systems. If either of the two hydraulic or riding on the brake pedal can result in abnor- systems loses normal capability, the remaining mally high brake temperatures, excessive lining...
Page 452: Electronic Brake Control System
450 STARTING AND OPERATING ELECTRONIC BRAKE CONTROL SYSTEM overslip of the rear wheels to avoid vehicle instability, and to prevent the rear axle from entering ABS before the Your vehicle is equipped with an advanced Electronic front axle. Brake Control system (EBC). This system includes Elec- tronic Brake Force Distribution (EBD), Anti-Lock Brake Brake System Warning Light System (ABS), Brake Assist System (BAS), Hill Start...
Page 453 STARTING AND OPERATING 451 • A slight drop of the brake pedal at the end of the stop. braking conditions. The system automatically prevents wheel lock, and enhances vehicle control during braking. These are all normal characteristics of ABS. The ABS performs a self-check cycle to ensure that the ABS is working properly each time the vehicle is started WARNING! and driven.
Page 454: Anti-Lock Brake Warning Light
452 STARTING AND OPERATING Anti-Lock Brake Warning Light WARNING! (Continued) The amber “Anti-Lock Brake Warning Light” will turn on • The ABS cannot prevent the natural laws of phys- when the ignition switch is turned to the ON position ics from acting on the vehicle, nor can it increase and may stay on for as long as four seconds.
Page 455: Brake Assist System (Bas)
STARTING AND OPERATING 453 Brake Assist System (BAS) WARNING! The BAS is designed to optimize the vehicle’s braking The Brake Assist System (BAS) cannot prevent the capability during emergency braking maneuvers. The natural laws of physics from acting on the vehicle, system detects an emergency braking situation by sens- nor can it increase the traction afforded by prevailing ing the rate and amount of brake application and then...
Page 456 454 STARTING AND OPERATING does not apply the throttle before this time expires, the is in PARK or NEUTRAL. For vehicles equipped with system will release brake pressure and the vehicle will a manual transmission if the clutch is pressed HSA will roll down the hill as normal.
Page 457 STARTING AND OPERATING 455 Towing With HSA WARNING! (Continued) HSA will also provide assistance to mitigate roll back • Failure to follow these warnings can result in a while towing a trailer. collision or serious personal injury. WARNING! Disabling And Enabling HSA •...
Page 458: Traction Control System (Tcs)
456 STARTING AND OPERATING For vehicles not equipped with the EVIC, perform the 8. Turn the ignition switch to the OFF position and then following steps: back to the ON position. If the sequence was com- pleted properly, the “ESC Off Indicator Light” will 1.
Page 459: Electronic Stability Control (Esc)
STARTING AND OPERATING 457 • Understeer - when the vehicle is turning less than to the wheel that is not spinning. BLD may remain enabled even if TCS and ESC are in a reduced mode. appropriate for the steering wheel position. The “ESC Activation/Malfunction Indicator Light”...
Page 460 458 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) ESC performance. Improperly inflated and un- accidents, including those resulting from excessive evenly worn tires may also degrade ESC perfor- speed in turns, driving on very slippery surfaces, or hydroplaning. ESC also cannot prevent accidents mance.
Page 461 STARTING AND OPERATING 459 Partial Off NOTE: • When in “Partial Off” mode, the TCS functionality of The “Partial Off” mode is intended for times when a more spirited driving experience is desired. This mode ESC, (except for the limited slip feature described in may modify TCS and ESC thresholds for activation, the TCS section), has been disabled and the “ESC Off which allows for more wheel spin than normally al-...
Page 462 460 STARTING AND OPERATING speeds greater than 30 mph (48 km/h), see your autho- WARNING! (Continued) rized dealer as soon as possible to have the problem accidents, including those resulting from excessive diagnosed and corrected. speed in turns, driving on very slippery surfaces, or The “ESC Activation/Malfunction Indicator Light”...
Page 463: Trailer Sway Control (Tsc)
STARTING AND OPERATING 461 NOTE: Trailer Sway Control (TSC) • The “ESC Activation/Malfunction Indicator Light” TSC uses sensors in the vehicle to recognize an exces- sively swaying trailer and will take the appropriate and the “ESC OFF Indicator Light” come on momen- actions to attempt to stop the sway.
Page 464: Electronic Roll Mitigation (Erm)
462 STARTING AND OPERATING Electronic Roll Mitigation (ERM) WARNING! This system anticipates the potential for wheel lift by Many factors, such as vehicle loading, road condi- monitoring the driver’s steering wheel input and the tions and driving conditions, influence the chance speed of the vehicle.
Page 465: Tire Safety Information
STARTING AND OPERATING 463 follow the trailer tongue weight recommendations. Refer TIRE SAFETY INFORMATION to “Trailer Towing” in this section for further informa- Tire Markings tion. When TSC is functioning, the “ESC Activation/ Malfunction Indicator Light” will flash, the engine power may be reduced and you may feel the brakes being applied to individual wheels to attempt to stop the trailer from swaying.
Page 466 464 STARTING AND OPERATING NOTE: tires is the same as for P-Metric tires except for the letters “LT” that are molded into the sidewall preced- • P (Passenger) — Metric tire sizing is based on U.S. ing the size designation. Example: LT235/85R16. design standards.
Page 467 STARTING AND OPERATING 465 Tire Sizing Chart EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on U.S. design standards, or ..blank..= Passenger car tire based on European design standards, or LT = Light truck tire based on U.S.
Page 468 466 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index – A numerical code associated with the maximum load a tire can carry H = Speed Symbol – A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions –...
Page 469: Tire Identification Number (Tin)
STARTING AND OPERATING 467 Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on The TIN may be found on one or both sides of the tire, the outboard side, then you will find it on the inboard however, the date code may only be on one side.
Page 470: Tire Terminology And Definitions
468 STARTING AND OPERATING EXAMPLE: DOT MA L9 ABCD 0301 01 = Number representing the year in which the tire was manufactured (two digits) – 01 means the year 2001 – Prior to July 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured.
Page 471 STARTING AND OPERATING 469 Term Definition Maximum Inflation Pressure The maximum inflation pressure is the maximum permissible cold tire inflation pressure for this tire. The maximum inflation pressure is molded into the sidewall. Recommended Cold Tire Inflation Pres- Vehicle manufacturer’s recommended cold tire inflation pressure sure as shown on the tire placard.
Page 472: Tire Loading And Tire Pressure
470 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Example Tire Placard Location (Door)
Page 473 STARTING AND OPERATING 471 Tire And Loading Information Placard Example Tire Placard Location (B-Pillar) Tire And Loading Information Placard This placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry.
Page 474 472 STARTING AND OPERATING 3. Tire size designed for your vehicle. To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of 4. Cold tire inflation pressures for the front, rear, and occupants and cargo should never exceed XXX lbs or spare tires.
Page 475 STARTING AND OPERATING 473 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if • If your vehicle will be towing a trailer, load from your “XXX” amount equals 1,400 lbs (635 kg) and there will trailer will be transferred to your vehicle.
Page 476 474 STARTING AND OPERATING...
Page 477: Tires - General Information
STARTING AND OPERATING 475 Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause collisions. recommended load capacity for your vehicle.
Page 478: Tire Inflation Pressures
476 STARTING AND OPERATING Fuel Economy WARNING! (Continued) Underinflated tires will increase tire rolling resistance • Unequal tire pressures from one side of the vehicle resulting in higher fuel consumption. to the other can cause the vehicle to drift to the right or left.
Page 479 STARTING AND OPERATING 477 At least once a month: mile (1.6 km) after sitting for a minimum of three hours. The cold tire inflation pressure must not exceed the • Check and adjust tire pressure with a good quality maximum inflation pressure molded into the tire side- pocket-type pressure gauge.
Page 480: Tire Pressures For High Speed Operation
478 STARTING AND OPERATING Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) WARNING! during operation. DO NOT reduce this normal pressure build up or your tire pressure will be too low. High speed driving with your vehicle under maxi- mum load is dangerous.
Page 481: Tire Types
STARTING AND OPERATING 479 Tire Repair Tire Types If your tire becomes damaged, it may be repaired if it All Season Tires — If Equipped meets the following criteria: All Season tires provide traction for all seasons (Spring, • The tire has not been driven on when flat. Summer, Fall and Winter).
Page 482 480 STARTING AND OPERATING Summer tires do not contain the all season designation or Snow Tires mountain/snowflake symbol on the tire sidewall. Use Some areas of the country require the use of snow tires Summer tires only in sets of four; failure to do so may during the Winter.
Page 483: Run Flat Tires - If Equipped
STARTING AND OPERATING 481 While studded tires improve performance on ice, skid See the tire pressure monitoring section for more infor- and traction capability on wet or dry surfaces may be mation. poorer than that of non-studded tires. Some states pro- Spare Tires —...
Page 484 482 STARTING AND OPERATING Spare Tire Matching Original Equipped Tire And T, S = Temporary Spare Tire Wheel — If Equipped Since this tire has limited tread life, the original equip- Your vehicle may be equipped with a spare tire and ment tire should be repaired (or replaced) and reinstalled wheel equivalent in look and function to the original on your vehicle at the first opportunity.
Page 485 STARTING AND OPERATING 483 limited-use spare wheel. This label contains the driving WARNING! (Continued) limitations for this spare. This tire may look like the replaced. Be sure to follow the warnings, which original equipped tire on the front or rear axle of your apply to your spare.
Page 486: Tire Spinning
484 STARTING AND OPERATING WARNING! (Continued) WARNING! equipment tire at the first opportunity and reinstall it Fast spinning tires can be dangerous. Forces gener- on your vehicle. Failure to do so could result in loss ated by excessive wheel speeds may cause tire dam- of vehicle control.
Page 487: Life Of Tire
STARTING AND OPERATING 485 worn to the tread wear indicators, the tire should be replaced. Refer to “Replacement Tires” in this section for further information. Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: •...
Page 488: Replacement Tires
486 STARTING AND OPERATING tread life. Rotation of these tires per the vehicle main- wear and correct cold tire inflation pressures. The manu- tenance schedule is highly recommended. facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance WARNING! when replacement is needed.
Page 489 STARTING AND OPERATING 487 you may have on tire specifications or capability. Failure WARNING! (Continued) to use equivalent replacement tires may adversely affect • Never use a tire with a smaller load index or the safety, handling, and ride of your vehicle. capacity, other than what was originally equipped on your vehicle.
Page 490: Tire Chains (Traction Devices)
488 STARTING AND OPERATING TIRE CHAINS (TRACTION DEVICES) CAUTION! Use of traction devices require sufficient tire-to-body To avoid damage to your vehicle or tires, observe the clearance. Follow these recommendations to guard following precautions: against damage. • Because of restricted traction device clearance be- •...
Page 491: Tire Rotation Recommendations
STARTING AND OPERATING 489 tires. Rotation will increase tread life, help to maintain CAUTION! (Continued) mud, snow and wet traction levels, and contribute to a • Observe the traction device manufacturer’s instruc- smooth, quiet ride. tions on the method of installation, operating Refer to the “Maintenance Schedule”...
Page 492: Tire Pressure Monitor System (Tpms)
490 STARTING AND OPERATING The tire pressure will vary with temperature by about 1 psi (7 kPa) for every 12°F (6.5°C). This means that when the outside temperature decreases, the tire pressure will de- crease. Tire pressure should always be set based on cold inflation tire pressure.
Page 493 STARTING AND OPERATING 491 The TPMS will continue to warn the driver of low tire For example, your vehicle may have a recommended cold pressure as long as the condition exists, and will not turn (parked for more than three hours) placard pressure of 33 off until the tire pressure is at or above the recommended psi (227 kPa).
Page 494 492 STARTING AND OPERATING NOTE: CAUTION! (Continued) • The TPMS is not intended to replace normal tire care warnings have been established for the tire size and maintenance, or to provide warning of a tire equipped on your vehicle. Undesirable system op- failure or condition.
Page 495: Premium System
STARTING AND OPERATING 493 • Seasonal temperature changes will affect tire pressure, and the TPMS will monitor the actual tire pressure in the tire. Premium System The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels.
Page 496 494 STARTING AND OPERATING • Various Tire Pressure Monitoring System messages, which display in the Electronic Vehicle Information Center (EVIC) • Tire Pressure Monitoring Telltale Light Tire Pressure Monitoring Low Pressure Warnings The “Tire Pressure Monitoring Telltale Light” will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires.
Page 497 STARTING AND OPERATING 495 update, the graphic display in the EVIC will change color seconds and then display dashes (- -) in place of the back to the original color, and the “Tire Pressure Moni- pressure value to indicate which sensor is not being toring Telltale Light”...
Page 498 496 STARTING AND OPERATING • If you install the compact spare tire in place of a road 4. Using tire chains on the vehicle. tire that has a pressure below the low-pressure warn- 5. Using wheels/tires not equipped with TPMS sensors. ing limit, upon the next ignition switch cycle, the “Tire The EVIC will also display a SERVICE TPM SYSTEM Pressure Monitoring Telltale Light”...
Page 499: General Information
STARTING AND OPERATING 497 solid, and the EVIC will display a SERVICE TPM General Information SYSTEM message for a minimum of five seconds and This device complies with Part 15 of the FCC rules and then display dashes (- -) in place of the pressure value. RSS-210 of Industry Canada.
Page 500: Fuel Requirements
498 STARTING AND OPERATING FUEL REQUIREMENTS Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations. If you experience these symptoms, try another brand of gasoline before consid- This engine is designed to meet all emis- ering service for the vehicle. sions regulations and provide optimum fuel economy and performance when us- Reformulated Gasoline...
Page 501: Gasoline/Oxygenate Blends
STARTING AND OPERATING 499 Gasoline/Oxygenate Blends are not the responsibility of the manufacturer and may void or not be covered under New Vehicle Limited Some fuel suppliers blend unleaded gasoline with oxy- Warranty. genates such as ethanol. E-85 Usage In Non-Flex Fuel Vehicles CAUTION! Non-Flex Fuel Vehicles (FFV) are compatible with gaso- line containing up to 15% ethanol (E-15).
Page 502: Mmt In Gasoline
500 STARTING AND OPERATING MMT In Gasoline that have these additives will help improve fuel economy, reduce emissions, and maintain vehicle perfor- Methylcyclopentadienyl Manganese Tricarbonyl (MMT) mance. Designated TOP TIER Detergent Gasoline con- is a manganese-containing metallic additive that is tains a higher level of detergents to further aide in blended into some gasoline to increase octane.
Page 503: Fuel System Cautions
STARTING AND OPERATING 501 Fuel System Cautions CAUTION! (Continued) • The use of fuel additives, which are now being CAUTION! sold as octane enhancers, is not recommended. Follow these guidelines to maintain your vehicle’s Most of these products contain high concentrations performance: of methanol.
Page 504: Carbon Monoxide Warnings
502 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! (Continued) time the vehicle is raised. Have any abnormal WARNING! conditions repaired promptly. Until repaired, drive Carbon monoxide (CO) in exhaust gases is deadly. with all side windows fully open. Follow the precautions below to prevent carbon monoxide poisoning: FLEXIBLE FUEL (3.6L ENGINE ONLY) —...
Page 505: Ethanol Fuel (E-85)
STARTING AND OPERATING 503 Fuel Requirements CAUTION! If your vehicle is E-85 compatible, it will operate on Only vehicles with the E-85 fuel filler door label or a unleaded gasoline with any octane rating, or solely E-85 yellow gas cap can operate on E-85. fuel, or any mixture of these fuels.
Page 506: Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles
504 STARTING AND OPERATING NOTE: FCA Material Standard MS-6395. It is recommended that engine oils that are API Certified and meet the require- • Use seasonally adjusted E-85 fuel (ASTM D5798). With ments of Material Standard MS-6395 be used. MS-6395 non-seasonally adjusted E-85 fuel, hard starting and contains additional requirements, developed during ex- rough idle following start up may be experienced even...
Page 507: Cruising Range
STARTING AND OPERATING 505 Cruising Range Maintenance Because E-85 fuel contains less energy per gallon/liter CAUTION! than gasoline, an increase in fuel consumption will be experienced. The miles per gallon (mpg)/kilometers per Do not use ethanol mixture greater than 85% in your liter and the driving range will decrease by approxi- vehicle.
Page 508 506 STARTING AND OPERATING WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being filled. • Never add fuel to the vehicle when the engine is running.
Page 509: Loose Fuel Filler Cap Message
STARTING AND OPERATING 507 properly. The MIL in the instrument cluster may turn CAUTION! on if the gas cap is not secured properly. Make sure • Damage to the fuel system or emissions control that the gas cap is tightened each time the vehicle is refueled.
Page 510: Vehicle Loading
508 STARTING AND OPERATING • Gross Axle Weight Rating (GAWR) rear VEHICLE LOADING • Vehicle Identification Number (VIN) The load carrying capacity of your vehicle is shown on the “Vehicle Certification Label”. This information • Type of Vehicle should be used for passenger and luggage loading as •...
Page 511: Overloading
STARTING AND OPERATING 509 Figure out the weight on the front and rear of the vehicle WARNING! separately. It is important that you distribute the load evenly over the front and rear axles. Because the front wheels steer the vehicle, it is important that you do not exceed the maximum front Overloading can cause potential safety hazards and or rear GAWR.
Page 512: Trailer Towing
510 STARTING AND OPERATING TRAILER TOWING exceed the GVWR. Refer to “Vehicle Loading/Vehicle Certification Label” in “Starting And Operating” for In this section you will find safety tips and information further information. on limits to the type of towing you can reasonably do with your vehicle.
Page 513 STARTING AND OPERATING 511 Gross Axle Weight Rating (GAWR) is 10% to 15% of the vehicle’s GTW for a conventional hitch. You must consider this as part of the load on your The GAWR is the maximum capacity of the front and rear vehicle.
Page 514: Trailer Hitch Classification
512 STARTING AND OPERATING Weight-Carrying Hitch equalizing) hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle A weight-carrying hitch supports the trailer tongue weight, and trailer configuration/loading to comply with Gross just as if it were luggage located at a hitch ball or some other Axle Weight Rating (GAWR) requirements.
Page 515 STARTING AND OPERATING 513 Trailer Hitch Classification Definitions Class Max. Trailer Hitch Industry Standards Class I - Light Duty 2,000 lbs (907 kg) Class II - Medium Duty 3,500 lbs (1 587 kg) Class III - Heavy Duty 5,000 lbs (2 268 kg) Class IV - Extra Heavy Duty 10,000 lbs (4 540 kg) Refer to the “Trailer Towing Weights (Maximum Trailer Weight Ratings)”...
Page 516: Trailer Towing Weights (Maximum Trailer Weight Ratings)
514 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain: GCWR (Gross Com- Max. GTW (Gross Max. Tongue Engine/Transmission Frontal Area bined Wt. Rating) Trailer Wt.) 2.4L/Automatic 6,000 lbs (2 721 kg) 22 sq ft...
Page 517: Trailer And Tongue Weight
STARTING AND OPERATING 515 NOTE: which will cause loss of control of the vehicle and trailer. Failure to load trailers heavier in front is the cause of • The trailer tongue weight must be considered as part many trailer collisions. of the combined weight of occupants and cargo, and Never exceed the maximum tongue weight stamped on should never exceed the weight referenced on the Tire...
Page 518: Towing Requirements
516 STARTING AND OPERATING Consider the following items when computing the Towing Requirements weight on the rear axle of the vehicle: To promote proper break-in of your new vehicle drive- • The tongue weight of the trailer. train components the following guidelines are recom- mended: •...
Page 519 STARTING AND OPERATING 517 information. When towing a trailer, never exceed the WARNING! (Continued) GAWR, or GCWR, ratings. • When hauling cargo or towing a trailer, do not overload your vehicle or trailer. Overloading can WARNING! cause a loss of control, poor performance, or dam- Improper towing can lead to a collision.
Page 520 518 STARTING AND OPERATING “Tires – General Information” in “Starting And Oper- WARNING! (Continued) ating” for proper tire inflation procedures. • Total weight must be distributed between the tow • Check the trailer tires for proper tire inflation pres- vehicle and the trailer such that the following four sures before trailer usage.
Page 521 STARTING AND OPERATING 519 Towing Requirements — Trailer Brakes WARNING! • Do not interconnect the hydraulic brake system or • Do not connect trailer brakes to your vehicle’s vacuum system of your vehicle with that of the trailer. hydraulic brake lines. It can overload your brake This could cause inadequate braking and possible system and cause it to fail.
Page 522 520 STARTING AND OPERATING CAUTION! (Continued) could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Towing Requirements — Trailer Lights And Wiring Whenever you pull a trailer, regardless of the trailer size, stoplights and turn signals on the trailer are required for motoring safety.
Page 523: Towing Tips
STARTING AND OPERATING 521 Towing Tips Before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Automatic Transmission The DRIVE range can be selected when towing. How- ever, if frequent shifting occurs while in DRIVE, use the AutoStick shift control to manually select a lower gear.
Page 524 522 STARTING AND OPERATING or frequent trailer towing”. Refer to the “Maintenance AutoStick Schedule” for the proper maintenance intervals. • When using the AutoStick shift control, select the NOTE: Check the four-speed automatic transmission highest gear that allows for adequate performance and fluid level before towing.
Page 525 STARTING AND OPERATING 523 Cooling System Highway Driving To reduce potential for engine and transmission over- Reduce speed. heating, take the following actions: Air Conditioning City Driving Turn off temporarily. When stopped for short periods, shift the transmission into NEUTRAL and increase engine idle speed. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition...
Page 526 524 STARTING AND OPERATING Recreational Towing — Front-Wheel Drive (FWD) CAUTION! Models • DO NOT flat tow this vehicle. Damage to the Recreational towing is allowed ONLY if the front wheels drivetrain will result. If this vehicle requires tow- are OFF the ground. This may be accomplished using a ing, make sure the drive wheels are OFF the tow dolly or vehicle trailer.
Page 527 STARTING AND OPERATING 525 Recreational Towing — All-Wheel Drive (AWD) CAUTION! Models Towing this vehicle with ANY of its wheels on the Recreational towing (with all four wheels on the ground, ground can cause severe transmission and/or power or using a towing dolly) is NOT ALLOWED. The only transfer unit damage.
Page 529 WHAT TO DO IN EMERGENCIES CONTENTS ▫ Spare Tire Removal ....534 HAZARD WARNING FLASHERS ...529 ▫...
Page 530 528 WHAT TO DO IN EMERGENCIES ▫ Front-Wheel Drive (FWD) Models ..555 TOWING A DISABLED VEHICLE ...552 ▫ All-Wheel Drive (AWD) Models ...554...
Page 531: Hazard Warning Flashers
WHAT TO DO IN EMERGENCIES 529 HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located in the In any of the following situations, you can reduce the instrument panel switch bank, above the climate controls. potential for overheating by taking the appropriate action.
Page 532: 2.4L Engine - If Equipped
530 WHAT TO DO IN EMERGENCIES 2.4L Engine — If Equipped CAUTION! On hot days the engine oil temperature may become too Driving with a hot cooling system could damage hot during sustained high-speed driving or if towing a your vehicle. If the temperature gauge reads “H,” trailer up long grades.
Page 533: Torque Specifications
WHAT TO DO IN EMERGENCIES 531 Torque Specifications Lug Nut/Bolt Torque **Lug Nut/ Lug Nut/ Bolt Size Bolt Socket Size 100 Ft-Lbs (135 N·m) M12 x 1.5 19 mm **Use only your Authorized Dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.
Page 534: Jacking And Tire Changing
532 WHAT TO DO IN EMERGENCIES WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. JACKING AND TIRE CHANGING WARNING! •...
Page 535: Jack Location
WHAT TO DO IN EMERGENCIES 533 WARNING! (Continued) under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • Never start or run the engine while the vehicle is on a jack.
Page 536: Preparations For Jacking
534 WHAT TO DO IN EMERGENCIES Preparations For Jacking 6. Block both the front and rear of the wheel diagonally opposite of the jacking position. For ex- 1. Park the vehicle on a firm, level surface as far from the ample, if changing the right front tire, edge of the roadway as possible.
Page 537 WHAT TO DO IN EMERGENCIES 535 NOTE: Assemble components 2 and 3 by seating the small ball at the end of component 2 in the small hole at the end of component 3. This will lock these components together. Assemble components 1 and 2 so that the wheel nut socket at the end of component 1 faces upward when seated on component 2.
Page 538: Spare Tire Stowage
536 WHAT TO DO IN EMERGENCIES 3. Pull the spare tire out from underneath the vehicle and Spare Tire Stowage raise it upright so the tire’s tread is on the ground. NOTE: Refer to “Spare Tire Removal” for information on 4.
Page 539: Jacking Instructions
WHAT TO DO IN EMERGENCIES 537 Jacking Instructions WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a WARNING! jack. • Do not get under the vehicle when it is on a jack. If Carefully follow these tire changing warnings to help prevent personal injury or damage to your you need to get under a raised vehicle, take it to a...
Page 540 538 WHAT TO DO IN EMERGENCIES Jack Warning Label CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. Jacking Locations 1. Remove the spare tire, jack, and jack-handle from stowage.
Page 541 WHAT TO DO IN EMERGENCIES 539 3. Place the jack in the notches underneath the lift area that is closest to the flat tire. Center the jack saddle between the drain flute formations on the sill flange. Turn the jack screw clockwise to firmly engage the jack saddle with the lift area of the sill flange.
Page 542 540 WHAT TO DO IN EMERGENCIES Rear Jacking Location Rear Jack Engaged With Jack Handle 4. Raise the vehicle by turning the jack screw clockwise with the jack handle. Raise the vehicle until the tire just clears the road surface and enough clearance is obtained to install the spare tire.
Page 543 WHAT TO DO IN EMERGENCIES 541 WARNING! CAUTION! Raising the vehicle higher than necessary can make Be sure to mount the spare tire with the valve stem the vehicle less stable. It could slip off the jack and facing outward. The vehicle could be damaged if the hurt someone near it.
Page 544 542 WHAT TO DO IN EMERGENCIES NOTE: 8. Lower the vehicle by turning the jack screw counter- clockwise with the jack handle. • For vehicles so equipped, do not attempt to install a center cap or wheel cover on the compact spare. 9.
Page 545: Road Tire Installation
WHAT TO DO IN EMERGENCIES 543 12. To stow the winch cable and retainer, fit the as- the lug nuts with the cone shaped end of the nut sembled jack-handle over the winch drive nut. Rotate toward the wheel. Lightly tighten the lug nuts. the jack-handle assembly clockwise until you hear the winch mechanism click three times.
Page 546 544 WHAT TO DO IN EMERGENCIES snapping the cover over the two lug nuts. Do not use a hammer or excessive force to install the cover. 4. Install the remaining lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts.
Page 547 WHAT TO DO IN EMERGENCIES 545 nut torque refer to Torque Specifications in this sec- WARNING! tion. If in doubt about the correct tightness, have them checked with a torque wrench by your authorized To avoid the risk of forcing the vehicle off the jack, dealer or service station.
Page 548: Jump-Starting
546 WHAT TO DO IN EMERGENCIES 5. After 25 miles (40 km) check the lug nut torque with a CAUTION! torque wrench to ensure that all lug nuts are properly seated against the wheel. Do not use a portable battery booster pack or any other booster source with a system voltage greater JUMP-STARTING than 12 Volts or damage to the battery, starter motor,...
Page 549 WHAT TO DO IN EMERGENCIES 547 WARNING! • Take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is ON. You can be injured by moving fan blades. • Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.
Page 550: Jump-Starting Procedure
548 WHAT TO DO IN EMERGENCIES 3. Remove the protective cover over the remote positive Jump-Starting Procedure (+) battery post. To remove the cover, push the locking tab and pull upward on the cover. WARNING! 4. If using another vehicle to jump-start the battery, park Failure to follow this jump-starting procedure could the vehicle within the jumper cables reach, set the result in personal injury or property damage due to...
Page 551 WHAT TO DO IN EMERGENCIES 549 3. Connect the negative end (-) of the jumper cable to the 6. Once the engine is started, remove the jumper cables negative (-) post of the booster battery. in the reverse sequence: Disconnecting The Jumper Cables 4.
Page 552: Freeing A Stuck Vehicle
550 WHAT TO DO IN EMERGENCIES If frequent jump-starting is required to start your vehicle, and REVERSE while gently pressing the accelerator you should have the battery and charging system in- pedal. Use the least amount of accelerator pedal pressure spected at your authorized dealer.
Page 553: Shift Lever Override
WHAT TO DO IN EMERGENCIES 551 NOTE: Push the ESC Off switch, to place the Electronic WARNING! Stability Control (ESC) system in ESC Partial Off mode, before rocking the vehicle. Refer to Fast spinning tires can be dangerous. Forces gener- “Electronic Brake Control”...
Page 554 552 WHAT TO DO IN EMERGENCIES 3. Open the center console and remove the shift lever 4. Push and maintain firm pressure on the brake pedal. override access cover (located in the front lower right 5. Insert a screwdriver or similar small tool into the corner of the console storage bin).
Page 555 WHAT TO DO IN EMERGENCIES 553 Towing Condition Wheel OFF the Ground FWD MODELS AWD MODELS Flat Tow NONE IF transmission is oper- NOT ALLOWED able: Wheel Lift Or Dolly Tow Rear NOT ALLOWED • Transmission in NEU- TRAL • 25 mph (40 km/h) max speed •...
Page 556 554 WHAT TO DO IN EMERGENCIES If the key fob is unavailable, or the vehicle’s battery is All-Wheel Drive (AWD) Models discharged, refer to “Shift Lever Override” in this section The manufacturer requires towing with all four wheels for instructions on shifting the transmission out of PARK OFF the ground.
Page 557 WHAT TO DO IN EMERGENCIES 555 Front-Wheel Drive (FWD) Models CAUTION! The manufacturer recommends towing your vehicle with Towing faster than 25 mph (40 km/h) or farther than all four wheels OFF the ground using a flatbed. 15 mi (24 km) with front wheels on the ground can If flatbed equipment is not available, and the transmis- cause severe transmission damage.
Page 559 MAINTAINING YOUR VEHICLE CONTENTS ▫ Engine Oil Filter ..... .568 ENGINE COMPARTMENT — 2.4L ..559 ▫...
Page 560 558 MAINTAINING YOUR VEHICLE ▫ Brake System ......585 REPLACEMENT BULBS ....606 ▫...
Page 561: Engine Compartment - 2.4L
MAINTAINING YOUR VEHICLE 559 ENGINE COMPARTMENT — 2.4L 1 — Engine Coolant Reservoir 7 — Power Distribution Center (Fuses) 2 — Power Steering Fluid Reservoir 8 — Air Cleaner Filter 3 — Engine Oil Fill 9 — Automatic Transmission Dipstick (4–Speed Only) 4 —...
Page 562: Engine Compartment - 3.6L
560 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 3.6L 1 — Engine Coolant Reservoir 5 — Air Cleaner Filter 2 — Power Steering Fluid Reservoir 6 — Washer Fluid Reservoir 3 — Brake Fluid Reservoir 7 — Engine Oil Dipstick 4 — Power Distribution Center (Fuses) 8 —...
Page 563: Onboard Diagnostic System - Obd Ii
MAINTAINING YOUR VEHICLE 561 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBD II. This system monitors further damage to the emission control system. It the performance of the emissions, engine, and automatic could also affect fuel economy and driveability.
Page 564: Emissions Inspection And Maintenance Programs
562 MAINTAINING YOUR VEHICLE A loose, improperly installed, or damaged fuel filler cap Your vehicle has a simple ignition actuated test, which may also turn on the MIL. you can use prior to going to the test station. To check if your vehicle’s OBD II system is ready, you must do the EMISSIONS INSPECTION AND MAINTENANCE following:...
Page 565: Replacement Parts
MAINTAINING YOUR VEHICLE 563 the ignition or start the engine. This means that your before going to the I/M station. The I/M station can fail vehicle’s OBD II system is not ready and you should your vehicle because the MIL is on with the engine not proceed to the I/M station.
Page 566: Maintenance Procedures
564 MAINTAINING YOUR VEHICLE NOTE: Intentional tampering with emissions control Besides those maintenance items specified in the fixed systems may void your warranty and could result in civil “Maintenance Schedule”, there are other components penalties being assessed against you. which may require servicing or replacement in the future. WARNING! CAUTION! •...
Page 567: Engine Oil
MAINTAINING YOUR VEHICLE 565 Checking the oil while the vehicle is on level ground and CAUTION! (Continued) only when the engine is hot, will improve the accuracy of transmission, or air conditioning. Such damage is the oil level readings. Maintain the oil level between the not covered by the New Vehicle Limited Warranty.
Page 568 566 MAINTAINING YOUR VEHICLE Change Engine Oil American Petroleum Institute (API) Engine Oil Identification Symbol The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to the “Maintenance Schedule” for further informa- This symbol means that the oil has tion.
Page 569 MAINTAINING YOUR VEHICLE 567 Engine Oil Viscosity — 2.4L Engine equivalent is recommended for all operating tempera- tures. This engine oil improves low temperature starting MOPAR SAE 5W-20 engine oil or equivalent Pennzoil or and vehicle fuel economy. Shell Helix is recommended for all operating tempera- tures.
Page 570: Engine Oil Filter
568 MAINTAINING YOUR VEHICLE Synthetic Engine Oils indiscriminately discarded, can present a problem to the environment. Contact your authorized dealer, service You may use synthetic engine oils provided the recom- station or governmental agency for advice on how and mended oil quality requirements are met, and the recom- where used oil and oil filters can be safely discarded in mended maintenance intervals for oil and filter changes your area.
Page 571: Engine Air Cleaner Filter
MAINTAINING YOUR VEHICLE 569 Engine Air Cleaner Filter Engine Air Cleaner Filter Selection Refer to the “Maintenance Schedule” in the “Mainte- The quality of replacement engine air cleaner filters nance Schedules” section for the proper maintenance varies considerably. Only high quality filters should be intervals.
Page 572 570 MAINTAINING YOUR VEHICLE To access the battery, turn the steering wheel fully to the WARNING! (Continued) right and remove the access panel from the inner fender • Battery posts, terminals, and related accessories shield. contain lead and lead compounds. Wash hands after handling.
Page 573: Air Conditioner Maintenance
MAINTAINING YOUR VEHICLE 571 Air Conditioner Maintenance WARNING! (Continued) For best possible performance, your air conditioner • The air conditioning system contains refrigerant should be checked and serviced by an authorized dealer under high pressure. To avoid risk of personal at the start of each warm season.
Page 574: A/C Air Filter - If Equipped
572 MAINTAINING YOUR VEHICLE manufacturer recommends that air conditioning service 2. Push the retaining tab on each side of the glove be performed by authorized dealer using recovery and compartment inward while gently pulling the glove recycling equipment. compartment door outward until both tabs clear the door opening in the instrument panel.
Page 575: Body Lubrication
MAINTAINING YOUR VEHICLE 573 4. Disengage the two retaining tabs that secure the filter 6. Install the A/C air filter with the arrow on the filter cover to the HVAC housing and remove the cover. pointing toward the floor. When installing the filter cover, make sure the retaining tabs fully engage the cover.
Page 576: Windshield Wiper Blades
574 MAINTAINING YOUR VEHICLE such as MOPAR Spray White Lube to assure quiet, easy Operation of the wipers on dry glass for long periods operation and to protect against rust and wear. Prior to may cause deterioration of the wiper blades. Always use the application of any lubricant, the parts concerned washer fluid when using the wipers to remove salt or dirt should be wiped clean to remove dust and grit;...
Page 577 MAINTAINING YOUR VEHICLE 575 3. Grab the bottom of the wiper blade and rotate it forward to unsnap the blade pivot pin from the wiper blade holder. 1 — Wiper Arm 2 — Pivot Cap NOTE: The rear wiper arm cannot be raised fully up- 1 —...
Page 578: Adding Washer Fluid
576 MAINTAINING YOUR VEHICLE 4. Install the wiper blade pivot pin into the wiper blade To prevent freeze-up of your windshield washer system holder at the end of the wiper arm, and firmly press in cold weather, select a solution or mixture that meets or the wiper blade until it snaps into place.
Page 579: Exhaust System
MAINTAINING YOUR VEHICLE 577 Exhaust System WARNING! The best protection against carbon monoxide entry into • Exhaust gases can injure or kill. They contain the vehicle body is a properly maintained engine exhaust carbon monoxide (CO), which is colorless and system.
Page 580 578 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- CAUTION! verter will not require maintenance. However, it is im- • The catalytic converter requires the use of un- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst leaded fuel only.
Page 581: Cooling System
MAINTAINING YOUR VEHICLE 579 To minimize the possibility of catalytic converter dam- Cooling System age: WARNING! • Do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in • When working near the radiator cooling fan, dis- motion.
Page 582 580 MAINTAINING YOUR VEHICLE applicable). If the engine coolant (antifreeze) is dirty or If the engine coolant (antifreeze) is dirty or contains rusty in appearance, the system should be drained, visible sediment, have an authorized dealer clean and flushed, and refilled with fresh engine coolant (anti- flush with OAT coolant (antifreeze) (conforming to freeze).
Page 583 MAINTAINING YOUR VEHICLE 581 CAUTION! (Continued) CAUTION! (Continued) • This vehicle has not been designed for use with Organic Additive Technology (OAT) engine cool- propylene glycol-based engine coolant (antifreeze). ant is different and should not be mixed with Use of propylene glycol-based engine coolant (an- Hybrid Organic Additive Technology (HOAT) en- tifreeze) is not recommended.
Page 584 582 MAINTAINING YOUR VEHICLE that meets the requirements of FCA Material Standard Please note that it is the owner’s responsibility to main- MS.90032. When adding engine coolant (antifreeze): tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where •...
Page 585 MAINTAINING YOUR VEHICLE 583 Cooling System Pressure Cap WARNING! (Continued) The cap must be fully tightened to prevent loss of engine pressure cap while the system is hot or under coolant (antifreeze), and to ensure that engine coolant pressure. (antifreeze) will return to the radiator from the coolant •...
Page 586 584 MAINTAINING YOUR VEHICLE Coolant Level additional engine coolant (antifreeze) is needed to main- tain the proper level, it should be added to the coolant 2.4L Engine — The coolant bottle provides a quick visual bottle. Do not overfill. method for determining that the coolant level is ad- equate.
Page 587: Brake System
MAINTAINING YOUR VEHICLE 585 • Check the coolant freeze point in the radiator and in • Do not change the thermostat for Summer or Winter the coolant expansion bottle. If engine coolant (anti- operation. If replacement is ever necessary, install freeze) needs to be added, the contents of the coolant ONLY the correct type thermostat.
Page 588 586 MAINTAINING YOUR VEHICLE Fluid level can be expected to fall as the brake pads wear. WARNING! (Continued) Brake fluid level should be checked when pads are high brake temperatures, excessive lining wear, and replaced. However, low fluid level may be caused by a possible brake damage.
Page 589: Automatic Transmission
MAINTAINING YOUR VEHICLE 587 WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or • Do not allow petroleum based fluid to contaminate moisture, use only new brake fluid or fluid that has the brake fluid. Brake seal components could be been in a tightly closed container.
Page 590 588 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! Using a transmission fluid other than the manufac- Do not use chemical flushes in your transmission as turer’s recommended fluid may cause deterioration the chemicals can damage your transmission compo- in transmission shift quality and/or torque converter nents.
Page 591 MAINTAINING YOUR VEHICLE 589 4. Place the shift lever momentarily into each gear posi- 7. Wipe the dipstick clean and reinsert it until seated. tion (allowing time for the transmission to fully en- Then, remove the dipstick and note the fluid level on gage in each position), ending with the transmission in both sides.
Page 592 590 MAINTAINING YOUR VEHICLE NOTE: If it is necessary to check the transmission below CAUTION! the operating temperature, the fluid level should be • Using a transmission fluid other than the manufac- between the two COLD (lower) holes on the dipstick with the fluid at approximately 80°F (27°C).
Page 593: Rear Drive Assembly (Rda) - Awd Models Only
MAINTAINING YOUR VEHICLE 591 Routine fluid level checks are not required, therefore the In addition, change the fluid and filter if the fluid transmission filler tube is capped and no dipstick is becomes contaminated (with water, etc.), or if the trans- provided.
Page 594: Power Transfer Unit (Ptu) - Awd Models Only
592 MAINTAINING YOUR VEHICLE Frequency Of Fluid Change Frequency Of Fluid Change Refer to the “Maintenance Schedule” for the proper Refer to the “Maintenance Schedule” for the proper maintenance intervals. maintenance intervals. Power Transfer Unit (PTU) – AWD Models Only Appearance Care And Protection From Corrosion Lubricant Selection Protection Of Body And Paint From Corrosion...
Page 595 MAINTAINING YOUR VEHICLE 593 The following maintenance recommendations will enable Washing you to obtain maximum benefit from the corrosion • Wash your vehicle regularly. Always wash your ve- resistance built into your vehicle. hicle in the shade using MOPAR Car Wash, or a mild car wash soap, and rinse the panels completely with What Causes Corrosion? clear water.
Page 596 594 MAINTAINING YOUR VEHICLE • If you detect any stone chips or scratches in the paint, CAUTION! touch them up immediately. The cost of such repairs is • Do not use abrasive or strong cleaning materials considered the responsibility of the owner. such as steel wool or scouring powder that will •...
Page 597 MAINTAINING YOUR VEHICLE 595 Wheel And Wheel Trim Care CAUTION! • All wheels and wheel trim, especially aluminum and Do not use scouring pads, steel wool, a bristle brush, chrome plated wheels, should be cleaned regularly or metal polishes. Do not use oven cleaner. These with a mild soap and water to prevent corrosion.
Page 598 596 MAINTAINING YOUR VEHICLE • For tough stains, apply MOPAR Total Clean, or a mild can act as an abrasive and damage the leather upholstery soap solution to a clean, damp cloth and remove stain. and should be removed promptly with a damp cloth. Use a fresh, damp towel to remove soap residue.
Page 599 MAINTAINING YOUR VEHICLE 597 Cleaning Headlights CAUTION! Your vehicle is equipped with plastic headlights and fog Direct contact of air fresheners, insect repellents, lights that are lighter and less susceptible to stone break- suntan lotions, or hand sanitizers to the plastic, age than glass headlights.
Page 600 598 MAINTAINING YOUR VEHICLE cleaner. Use caution when cleaning the inside rear win- Seat Belt Maintenance dow equipped with electric defrosters or windows Do not bleach, dye, or clean the belts with chemical equipped with radio antennas. Do not use scrapers or solvents or abrasive cleaners.
Page 601: Cleaning The Cupholders
MAINTAINING YOUR VEHICLE 599 WARNING! (Continued) WARNING! (Continued) disassemble or modify the system. Seat belt assem- to use proper fuses may result in serious personal blies must be replaced after a collision if they have injury, fire and/or property damage. •...
Page 602 600 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini-Fuse Description F100 30 Amp Pink – 110V AC Inverter – If Equipped F101 – 10 Amp Red Interior Lights F102 – 20 Amp Yellow Cigar Lighter in Instrument Panel/Left Rear Power Outlet F103 –...
Page 603 MAINTAINING YOUR VEHICLE 601 Cavity Cartridge Fuse Mini-Fuse Description F116 30 Amp Pink – Rear Defroster (EBL) F117 – 10 Amp Red Heated Mirrors F118 – 10 Amp Red Occupant Restraint Controller F119 – 10 Amp Red Steering Column Control Module F120 –...
Page 604: Underhood Fuses (Power Distribution Center)
602 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini-Fuse Description F131 – 10 Amp Red Passenger Assistance/Hands Free System – If Equipped F132 – 10 Amp Red Tire Pressure Module F133 – 10 Amp Red Spare Underhood Fuses (Power Distribution Center) The power distribution center is located in the engine compartment.
Page 605 MAINTAINING YOUR VEHICLE 603 Cavity Cartridge Fuse Mini-Fuse Description F101 60 Amp Yellow – Interior Power Distribution Center Rail F102 60 Amp Yellow – Interior Power Distribution Center Rail F103 60 Amp Yellow – Interior Power Distribution Center Rail F105 60 Amp Yellow –...
Page 606 604 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini-Fuse Description F147 30 Amp Pink – Spare F148 40 Amp Green – Radiator Fan Motor F149 30 Amp Pink – Starter Solenoid F150 – 25 Amp Clear Powertrain Control Modules F151 30 Amp Pink –...
Page 607 MAINTAINING YOUR VEHICLE 605 Cavity Cartridge Fuse Mini-Fuse Description F163 50 Amp Red – Cabin Heater #2 – If Equipped F164 – 25 Amp Clear Powertrain Auto Shutdown F165 – 20 Amp Yellow Powertrain Shutdown F166 – 20 Amp Yellow Spare F167 –...
Page 608: Replacement Bulbs
606 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini-Fuse Description F178 – 25 Amp Clear Sunroof – If Equipped F179 – 10 Amp Red Battery Sensor F181 100 Amp Blue – Electrohydraulic Steering (EHPS) – If Equipped F182 50 Amp Red –...
Page 609 MAINTAINING YOUR VEHICLE 607 Exterior Bulbs Bulb Number Low Beam Headlamp 9006 High Beam Headlamp 9005 Front Park/Turn Signal 3757AK Side Marker Lamp Front Fog Lamp PSX24W or 2504 Center High Mounted Stop Lamp (CHMSL) LED (Serviced at Authorized Dealer) License Lamp Exterior Bulbs –...
Page 610: Bulb Replacement
608 MAINTAINING YOUR VEHICLE Exterior Bulbs – Rear (Bulb Version) Bulb Number Rear Tail/Stop/Turn Signal Lamp P27/7W or 3157 Rear Tail (Liftgate) Lamp P27/7W or 3157 Backup Lamp P27/7W or 3157 NOTE: It may be necessary to remove the air cleaner BULB REPLACEMENT filter housing and position the Totally Integrated Power NOTE: Lens fogging can occur under certain atmo-...
Page 611: Front Fog Lamp
MAINTAINING YOUR VEHICLE 609 CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. 4. Install the bulb and connector assembly into the headlamp housing and rotate it ¼...
Page 612: Rear Turn Signal And Backup Lamp
610 MAINTAINING YOUR VEHICLE 2. Remove the electrical connector from the fog lamp CAUTION! housing. Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol.
Page 613 MAINTAINING YOUR VEHICLE 611 Changing The Rear Turn Signal Lamp 3. Carefully insert a trim stick (plastic flat-blade tool) between the body panel and the outboard side of the 1. Open the liftgate. tail lamp housing with one hand and grasp the flange 2.
Page 614 612 MAINTAINING YOUR VEHICLE Changing The Backup Lamp 3. Carefully insert a trim stick (plastic flat-blade tool) between the tail lamp housing and the liftgate. Use the 1. Open the liftgate. trim stick and hand pressure together to disengage the 2.
Page 615: License Plate Lamp
MAINTAINING YOUR VEHICLE 613 5. Remove the bulb from the connector socket and install the replacement bulb. 6. Install the bulb and connector assembly into the housing and rotate the connector ¼ turn clockwise to lock it in place. 7. Reinstall the tail lamp housing and fasteners. License Plate Lamp 1.
Page 616: Fluid Capacities
614 MAINTAINING YOUR VEHICLE 3. Hold the lens with one hand and rotate the bulb’s 5. Install the bulb and connector assembly into the lens electrical connector ¼ turn counterclockwise with the and rotate the connector ¼ turn clockwise to lock it in other hand and then separate the bulb and connector place.
Page 617 MAINTAINING YOUR VEHICLE 615 U.S. Metric Cooling System* 2.4L Engine and Single or Dual-Zone Climate Control System 10.7 Quarts 10.1 Liters (MOPAR Antifreeze/Engine Coolant 10 Year/150,000 Mile For- mula) 2.4L Engine and Three-Zone Climate Control System (MOPAR 11.6 Quarts 11 Liters Antifreeze/Engine Coolant 10 Year/150,000 Mile Formula) 3.6L Engine and Single or Dual-Zone Climate Control System 13.1 Quarts...
Page 618: Fluids, Lubricants, And Genuine Parts
616 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend you use MOPAR Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology). Engine Oil We recommend you use API Certified SAE 5W-20 En- gine Oil, meeting the requirements of FCA Material Standard MS-6395 such as MOPAR, Pennzoil, and Shell Helix.
Page 619 MAINTAINING YOUR VEHICLE 617 CAUTION! CAUTION! (Continued) • Do not use water alone or alcohol-based engine • Mixing of engine coolant (antifreeze) other than coolant (antifreeze) products. Do not use additional specified Organic Additive Technology (OAT) en- rust inhibitors or antirust products, as they may not gine coolant (antifreeze), may result in engine be compatible with the radiator engine coolant and damage and may decrease corrosion protection.
Page 620: Chassis
618 MAINTAINING YOUR VEHICLE Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission Use only ATF+4 Automatic Transmission Fluid. Failure to use ATF+4 fluid may affect the function or performance of your transmission. We recommend MOPAR ATF+4 fluid. Power Transfer Unit (PTU) We recommend you use MOPAR Gear Lubricant 75W- Rear Drive Assembly (RDA) We recommend you use MOPAR Gear Lubricant 75W-...
Page 621: Maintenance Schedules
MAINTENANCE SCHEDULES CONTENTS ▫ Maintenance Chart.....622 MAINTENANCE SCHEDULE ....620...
Page 622 620 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE scheduled oil change is performed by someone other than your authorized dealer, the message can be reset by Your vehicle is equipped with an automatic oil change referring to the steps described under “Electronic Vehicle indicator system.
Page 623 MAINTENANCE SCHEDULES 621 Once A Month Or Before A Long Trip: At Every Oil Change Interval As Indicated By Oil • Check engine oil level. Change Indicator System: • Change oil and filter. • Check windshield washer fluid level. • Rotate the tires. Rotate at the first sign of irregu- •...
Page 624 622 MAINTENANCE SCHEDULES Maintenance Chart Refer to the Maintenance Schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Inspections Inspect the CV joints. Inspect front suspension, tie rod ends, and replace if necessary.
Page 625 MAINTENANCE SCHEDULES 623 Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Maintenance Replace engine air filter. Replace air conditioning filter. Replace spark plugs (2.4L En- gine). ** Replace spark plugs (3.6L En- gine). ** Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first.
Page 626 624 MAINTENANCE SCHEDULES Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Change the automatic transmis- sion fluid and filter. Change the automatic transmis- sion fluid and filter if using your vehicle for any of the following: police, taxi, fleet, or frequent trailer towing.
Page 627 MAINTENANCE SCHEDULES 625 ** The spark plug change interval is mileage based only, yearly intervals do not apply. WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
Page 629 IF YOU NEED CONSUMER ASSISTANCE CONTENTS ▫ Customer Assistance For The Hearing Or SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE ..... . .629 Speech Impaired (TDD/TTY) .
Page 630 628 IF YOU NEED CONSUMER ASSISTANCE ▫ Traction Grades ..... . .635 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES ....635 ▫...
Page 631: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 629 SUGGESTIONS FOR OBTAINING SERVICE FOR Be Reasonable With Requests YOUR VEHICLE If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with Prepare For The Appointment the service advisor and list the items in order of priority.
Page 632: Fca Us Llc Customer Center
630 IF YOU NEED CONSUMER ASSISTANCE • Authorized dealer name facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed • Vehicle Identification Number (VIN) correctly and in a timely manner. • Vehicle delivery date and mileage This is why you should always talk to an authorized FCA US LLC Customer Center dealer service manager first.
Page 633: In Mexico Contact
IF YOU NEED CONSUMER ASSISTANCE 631 In Mexico Contact Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) Av. Prolongacion Paseo de la Reforma, 1240 To assist customers who have hearing difficulties, the Sante Fe C.P. 05109 manufacturer has installed special TDD (Telecommuni- Mexico, D.
Page 634 632 IF YOU NEED CONSUMER ASSISTANCE Warranty expires. The manufacturer stands behind only We appreciate that you have made a major investment the manufacturer’s service contracts. If you purchased a when you purchased the vehicle. An authorized dealer manufacturer’s service contract, you will receive Plan has also made a major investment in facilities, tools, and Provisions and an Owner Identification Card in the mail training to assure that you are absolutely delighted with...
Page 635: Warranty Information
IF YOU NEED CONSUMER ASSISTANCE 633 WARRANTY INFORMATION If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in See the Warranty Information Booklet, located on the a group of vehicles, it may order a recall and remedy DVD, for the terms and provisions of FCA US LLC campaign.
Page 636: Publication Order Forms
634 IF YOU NEED CONSUMER ASSISTANCE defect to the Canadian government should contact Trans- complete working knowledge of the vehicle, system, port Canada, Motor Vehicle Defect Investigations and and/or components is written in straightforward lan- Recalls at 1-800-333-0510 or go to http://www.tc.gc.ca/ guage with illustrations, diagrams, and charts.
Page 637: Department Of Transportation Uniform Tire Quality Grades
IF YOU NEED CONSUMER ASSISTANCE 635 starting, operating, emergency and maintenance proce- All passenger vehicle tires must conform to Federal dures as well as specifications, capabilities and safety tips. safety requirements in addition to these grades. Call toll free at: Treadwear •...
Page 638: Temperature Grades
636 IF YOU NEED CONSUMER ASSISTANCE specified government test surfaces of asphalt and concrete. passenger vehicle tires must meet under the Federal A tire marked C may have poor traction performance. Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory WARNING! test wheel, than the minimum required by law.
Page 639 INDEX...
Page 640 638 INDEX About Your Brakes .....446, 449 Knee Impact Bolsters .....67 Adding Engine Coolant (Antifreeze) .
Page 641 INDEX 639 Alterations/Modifications, Vehicle ....7 Special Additives ..... . .588 Antifreeze (Engine Coolant).
Page 642 640 INDEX Body Mechanism Lubrication ....573 Caps, Filler B-Pillar Location ......470 Fuel .
Page 643 INDEX 641 Chains, Tire ......488 Seating Positions ......88 Changing A Flat Tire .
Page 644 642 INDEX Cooling System......579 Dealer Service......563 Adding Coolant (Antifreeze) .
Page 645 INDEX 643 Remote Keyless Entry (RKE) ....30 Electronic Throttle Control Warning Light ..311 Door Locks, Automatic ..... .32 Electronic Vehicle Information Center Door Opener, Garage.
Page 646 644 INDEX Compartment Identification ....560 Entry System, Illuminated ....21 Coolant (Antifreeze) .
Page 647 INDEX 645 Flexible Fuel Vehicles Fog Lights ......227, 609 Cruising Range ......505 Fog Light Service .
Page 648 646 INDEX Tank Capacity ......614 GVWR ....... . .508 Fuel, Flexible .
Page 649 INDEX 647 Heated Mirrors ......123 Instrument Panel Lens Cleaning ....598 Heater, Engine Block .
Page 650 648 INDEX Key-In Reminder ......14 Lights ......111, 224 Keyless Enter-N-Go .
Page 651 INDEX 649 High Beam ......229, 608 Service ......606, 608 High Beam/Low Beam Select .
Page 652 650 INDEX Luggage Rack (Roof Rack) ....290 Exterior Folding ......123 Lug Nuts .
Page 653 INDEX 651 Oil, Engine ......565, 616 Operating Precautions ..... .561 Capacity .
Page 654 652 INDEX Distribution Center (Fuses) ....602 Pretensioners Door Locks ......31 Seat Belts .
Page 655 INDEX 653 Rear Window Features .....288 Remote Starting Rear Wiper/Washer......288 Exit Remote Start Mode .
Page 656 654 INDEX Safety Checks Inside Vehicle ....109 Seat Belts ......48, 109 Safety Checks Outside Vehicle .
Page 657 INDEX 655 Rear Folding ..... . .213, 220 Snow Tires ......480 Reclining .
Page 658 656 INDEX Steering Taillights .......610 Column Controls ..... . .228 Telescoping Steering Column .
Page 659 INDEX 657 Pressure Monitor System (TPMS) ... .490 Guide .......514 Pressure Warning Light .
Page 660 658 INDEX Transmission Screen Activated Features ....22, 336 Automatic ......429, 587 Things You Should Know About Your Filter .
Page 661 INDEX 659 Making A Second Call While Current Call Is In Vanity Mirrors ......123 Progress .
Page 662 660 INDEX Water Windshield Washers ....231, 234 Driving Through ......442 Fluid .
Page 663 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.

This manual is also suitable for:

Journey 2016

Dodge 2016 Journey Owner's Manual

Introduction

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

Quick Links

Chapters

Related Manuals for Dodge 2016 Journey

Summary of Contents for Dodge 2016 Journey