Do you have a question about the StitchFold and is the answer not in the manual?
Questions and answers
DORA RUIZ
May 27, 2025
MY MBM BOOKLET MAKER IS NOT STITCHING. IT WILL FOLD BUT NOT STITCH. I HAVE CHECKED EVERYTHING IN TROUBLESHOOTING. THE 2 LITTLE CYLINDER POLES WILL NOT GO DOWN.
Improved Productivity: With StitchFold, you can jog, stitch, and fold more than 65,000 booklets at a maximum speed of 2,300 finished booklets per hour - without stopping to reload staples. StitchFold's variable work thickness capacity handles from 2 sheets to a one hundred page booklet with no setup changes or adjustments.
StitchFold SAFETY SAFETY PRECAUTIONS AND PROCEDURES 1 . Make sure electrical power is turned off 4 . A well maintained machine is a safer ma- before performing any adjustment or main- chine. Clean and lubricate the machine at tenance.
http://www.monomachines.com/ ASSEMBLY DRAWING Main Table C. Right Side Cover Right Side Guide A. Front Guard Jog Fingers B. Top Guard Main Table Belt Delivery Table F. Rear Cover Secondary Table G. Roller Guard D. Left Side Cover E. Front Cover Left Side Guide Hand Crank For More Info...
LUBRICATION: CLEANING: Disconnect electrical power. Next, remove the front Use MBM Roller Wash (#0735) to clean the belts. cover and both side covers. Use MBM Roller Wash (#0735) to clean the folding Use SAE-20 oil to lubricate porous bronze bearings, rollers.
http://www.monomachines.com/ MAIN CONTROL PANEL POWER STITCH COUNTS A. Pilot Light: Glows to indicate that electrical power D. Counter: Digital counter records the number of is turned on. sets that pass through the machine. A manual reset button returns the counter to zero after each B.
StitchFold OPERATION & SETUP and pull it to the left until it stops at the fully jogged position. In this position, the paper must fit perfectly between the side guides. If there is a gap or the BOOKLETMAKING paper buckles, loosen the thumb screw on the right- hand side guide and move it in the correct direction.
http://www.monomachines.com/ OPERATION: SIDE STITCHING Turn on power and select "STITCH ON". Square up a set of paper sheets by hand, and lay the front edge on the table between the side guides. Push until the front edge is under the ski, and then let go. Side stitching can be done with 5.5"...
StitchFold fingers. If the standard fold gate returns early and CORNER STITCHING causes a jam or double stitch, turn the gate timer clockwise enough to prevent the problem. Lower the folding gate by pressing the toggle switch located on the secondary table. The side stitched...
http://www.monomachines.com/ ADJUSTMENTS GATE TIMER BOOKLET SQUARENESS The adjusting knob for the gate timer is located on Check the finished booklet. If the stitches are prop- the back of the machine's left side cover. It controls erly located on the fold, but the fold is off center, the amount of time that the stop gate is held down adjust the gates by turning the hand crank until sets each cycle after the stitches have been driven into the...
2. Spray furniture polish or wax on the entry and through the machine. Caution: Do not get polish or wax on paper drive belt. 4. Inconsistent fold. 1. Use MBM Roller Wash (#0735) to clean all four folding rollers. 2. Use MBM Roller Wash (#0735) to clean paper drive belt.
Page 13
http://www.monomachines.com/ PROBLEM: SOLUTION: 6. Stitch heads won't cycle. 1. Make sure that Stitch on/off switch is in "on" position. 7. Loud banging/clicking noise when stitch 1. Lubricate head per the "External Lubrication Sheet" pro- heads cycle. vided with the stitch heads. (Lubrication instructions also appear in the EZ Thread Owners Manual.) Pay special attention to the rotator lubrication.
Page 14
http://www.monomachines.com/ 3134 Industry Dr. N. Charleston, SC 29418 1-800-223-2508 1-843-552-2700 Fax: 1-843-552-2974 www.mbmcorp.com FORM QF96 6-9-05 http://www.monomachines.com/...
Need help?
Do you have a question about the StitchFold and is the answer not in the manual?
Questions and answers
MY MBM BOOKLET MAKER IS NOT STITCHING. IT WILL FOLD BUT NOT STITCH. I HAVE CHECKED EVERYTHING IN TROUBLESHOOTING. THE 2 LITTLE CYLINDER POLES WILL NOT GO DOWN.