Linksys SLM248G4S (G5) User Manual page 25

Chapter 
Unt No.
The unit (switch) that you are managing. The
default is the Master unit's number. To manage a different
unit, select its number from the drop-down menu.
Port The port number (preceded by the unit number).
For example, 2/e1 indicates Unit 2, Ethernet Port 1.
Descrpton
The user-defined port description.
Admnstratve Status Select Down to take the port
offline. When Up is selected, the port can be accessed
normally.
Lnk Status The port's operational status. The value is
either Up (the port has an active connection) or Down
(the port has no active connection, or has been taken
offline by an administrator).
Speed The port's configured rate in Mbps.
Duplex The port's current duplex mode, Half or Full.
MDI/MDIX The port's MDI/MDIX type. The MDI setting is
used if the port is connected to an end station. The MDIX
setting is used if the port is connected to a hub or another
switch.
Flow Control
This is the flow control status of the port. It
is active when the port uses Full Duplex Mode.
Type
Displays the port type.
LAG
This indicates if the port belongs to a LAG.
Port Configuration
The Port Configuration screen lets you configure a port's
settings. To use this screen, click Detal in the Detail
column on the Port Settings screen.
Port Management > Port Settings> Port Configuration
The Port Configuration screen contains the following fields
("Read-only" indicates that a field cannot be edited).
24/48-Port 10/100 + 4-Port Ggabt Reslent Clusterng Smart Swtch wth 2 Combo SFPs
Configuration Using the Web-based Utility
Port
The port number. To edit the information for
another port, select the port from the drop-down menu.
(Port numbers consist of either "e" for Ethernet, or "g" for
Gigabit, followed by the appropriate number.)
Descrpton
The user-defined port description of up to
64 characters. This field is blank by default.
Port Type
(Read-only) The port's connection type and
speed. The types are:
copper The port has a copper connection.
•
ComboC The Gigabit port has a copper connection.
•
ComboF The Gigabit port has a fiber optic
•
connection.
The port speed is prefixed onto the type, for example
10M-copper indicates a 10 Mbps copper connection.
Admn Status The port's administrative status. Select
either Up or Down to enable or disable traffic forwarding
through the port.
Current Port Status (Read-only) The port's connection
status, either Up or Down.
Reactvate Suspended Port
suspended, select this checkbox to reactivate the port.
Operatonal Status
(Read-only) Displays whether the
port is operational or non-operational.
Admn Speed Use this to manually set the port's
configured transmission rate in Mbps. You can select 10M,
100M, or 1000M (Gigabit ports only). Before you change
this setting, make sure that Auto Negotiation is disabled.
Current Port Speed (Read-only) The port's current rate
in Mbps.
Admn Duplex The port's duplex mode, either Full or
Half.
Current Duplex Mode
duplex mode.
Auto Negotaton Select Enable (default) or Dsable
to enable or disable Auto-Negotiation on the port. Auto-
Negotiation allows a port to advertise its transmission rate,
duplex mode, and flow control settings to other ports. If
you are using an SFP module on a port, Auto Negotiation
for that port should be set to Disable.
Current Auto Negotaton
Auto-Negotiation status.
Admn Advertsement
mode(s) that the port will advertise. The available speeds
are determined by the port type. The following capabilities
are supported.
Max Capablty
The port advertises all speeds and
•
duplex mode settings.
If the port has been
(Read-only) The port's current
(Read-only) The port's current
Select the speed(s) and duplex
19